EMI-REDD47-pre-sm维修电路原理图.pdf

RadioFans.CN 收音机爱 好者资料库Home | R.47 | Audio Demo | Technical & Historical | News | Contact | Terms We are not accepting orders for the R.47 MkII at this time Revolution Recording Equipment R.47 MkIIThe Classic British Vacuum-Tube Microphone AmplifierThe Revolution Recording Equipment Microphone Amplifier Type: R.47 is a single channel microphone and line valveamplifier based on a true classic. The Class A circuitry utilizes a pentode to triode configuration that provides up to 46dBof effective gain between an incoming signal and the balanced line level output.While derived from a vintage design, many refinements have been employed which take advantage of contemporaryelectronic technology. The signal-to-noise ratio is extremely good, and the equivalent hum and noise can be taken asequal to or better than 130 dBu referred to the input when the amplifier is set for maximum gain. The unit is capable ofan output level of +23 dBu on overload peaks before severe audible distortion becomes apparent.The vacuum-tube circuitry adds warmth and colour to the bass and the low-mid range of the frequency spectrum,resulting in a distinct richness to vocals, drums and bass. The frequency response is relatively flat through the upper endof the audio spectrum, with a wonderfully ethereal and open high end not typically associated with valve designs. Theamplifier circuitry has a very fast response that captures every delicate dynamic nuance of vocals and instrumenttransients. What truly distinguishes the R.47 is the way signals acquire a clarity and presence that floats them to thefront of the mix, this characteristic is consistent through a wide range of sources, from inexpensive dynamic microphonesto classic valve types.John Hinson, acclaimed for his achievements with Universal Audio, is the engineer behind the Revolution equipmentdesign and development. For this very special endeavor, John embraced two important principles in his designphilosophy: simplicity and uncompromising standards. The signal path requires only the essentials, especially for theactive amplification circuitry. The audio signal path uses only the highest quality commercial components, and customtransformers that meet rigorous standards. The painted steel chassis and engraved front panel complement the sturdyselectors and switches, and the solid construction is built to service studios for decades to come.Partial List Of UsersAbbey Road StudiosBrian Kehew (Recording The Beatles)East West Studios (Formerly Cello)Billy Corgan (Smashing Pumpkins)Marc Streitenfeld (Film Composer)Steve Kempster (Film Score Engineer/Mixer)05/03/2009Revolution Recording Equipment R 收音机爱 好者资料库FeaturesHand assembled using only the finest components (Hovland, Caddock, Mills)Selected New Old Stock (NOS) vacuum tubesCustom made gold plated switches (ELMA)Massive, custom-wound input and output transformersFully regulated, over-designed H.T. & L.T. power suppliesSwitched gain and attenuator controls for repeatabilityCardas and Kimber chassis wiringNo silk-screen! - front panels are engraved and paintedThick, welded steel chassis for extreme durabilitySpecificationsSource Impedance: 200ohmsInput Loading Impedance: 2K ohms (attenuator off)Maximum Input Level 20 Hz: +7dBu (attenuator & pad off)Minimum Gain: -4dBMaximum Gain: +46dBFrequency Response: +/- 0.25dB 20Hz to 20kHz (high end -3dB point 48 kHz)Signal to Noise Ratio: 80dBEquivalent Input Noise: -130dBInternal Output Impedance: 50 ohmsSuggested Minimum Load: 450 ohmsMaximum Output Level: +23 dBuPower Requirements: 120 or 240 VAC, 50/60 HzDimensions: 19 W, 3.5 H, 7 DWeight: 19lbs DetailsStandard Single Channel R.47 MSRP: $3000.00 USDCustom Matched R.47 Units: Please InquireThe R.47 Microphone Amplifier is available only by special order at this timeDelivery Time: Please InquireR.47 SIGNAL DIAGRAM05/03/2009Revolution Recording Equipment R INPUTBalanced Microphone Input. Pin 2 + with switchable Phantom Power. 200 ohm Impedance.MIC. ATTEN.Eleven Position Input Attenuator Network (Pad) with a range from -20dB to 0dB in 2dBincrements. The Microphone Attenuator is a Pad network that will change the impedance of theinput load. Subsequently, the increased impedance will change the character of the microphoneresponse changing the colour of the signal.10dB PADOn/Off Switch for fixed 10 dB input pad.BASS LIFTA unique passive filter circuit to compensate for a loss in low frequencies when usingmicrophones with a figure-of-eight pick-up pattern.AMPLIFIERThe amplifier consists of two valve stages, resistance-capacitance coupled with two loops ofnegative feedback. In the block diagram, the input and output transformers are nested in theamplifier section.GAINCONTROLSFour Position Rotary Selector to control amplifier gain (frequency compensated) fixed at 34dB,40dB, and 46dB. The optimal setting for the Gain control is 40dB. Not only does this conform tothe original specifications, but it has the best colour for general purposes from vocal to instrumentrecording. POLARITYThe Polarity reverse switch reverses the output phase from Pin 2 + to Pin 3 +OUTPUTFloating Balanced Line Level output. Pin 2 +R.47 CONTROLS1. MIC. ATTEN. (dB)Eleven Position Input Attenuator Network (Pad) with a range from -20dB to 0dB in 2dBincrements.2. 10dB PADOn/Off Switch for fixed 10 dB input pad.3. GAINFour Position Rotary Selector to control amplifier gain (frequency compensated) fixed at34dB, 40dB, and 46dB. 4. POLARITYOn/Off Switch for polarity (phase) reversal of the output signal.5. +48VOn/Off Switch for supplying phantom power (48V) to non-valve condenser microphones.6. BASS LIFTOn/Off Switch for a unique passive filter circuit to compensate for a loss in low frequencieswhen using microphones with a figure of 8 pick-up pattern.7. GAIN TRIMLocked fine gain adjustment control for balancing gains of matched pairs of R.47 amplifiers. The range of adjustment depends on the setting of the main gain control (# 3 above) but isapprox. +/- 1 dB.05/03/2009Revolution Recording Equipment R STUDIOREGISTRATIONCustom units require component and tube matching. These are issued with the Studio Nameand Serial Number engraved on the front panel.9. POWEROn/Off switch for main AC power.05/03/2009Revolution Recording Equipment R 05/03/2009 19:22:55http:/ 05/03/2009 19:22:32