Bogen-MT125B-pa-sm维修电路原理图.pdf

A DIVISION OF LEAR SIEGLER, INC.BOOSTER AMPLIFIERS MODELS MT-60A & MT-125BUNPACKING INPUT CONNECTIONSThe amplifier was thoroughly checked before leaving thefactory. Inspect the amplifier and shipping container carefullyfor evidence of improper handling during shipment. In case ofdamage, make an immediate claim to the dealer or distributorfrom whom the unit was purchased. If the amplifier was shippedto you, notify the carrier without delay and file a claim.Keep input leads away from the output leads and AC powercables. Unless the driving source provides a low-impedanceoutput, keep the input lead under ten feet in length. Refer to“Companion Units and Accessories” for Bogen preamplifierssuitable for use with the amplifier.TECHNICAL SPECIFICATIONSMT60A MT125BRATED OUTPUT POWER 60W 125WTOTAL HARMONIC DISTORTION Less than 2% at rated output 50 to 15,000 HzFREQUENCY RESPONSE 2 dB 20 to 20,000 HzHUM & NOISE -85 dB below rated outputREGULATION Better than 2 dB no load to full loadINPUT SENSITIVITY 200mV for rated outputINPUT IMPEDANCE Hi-Z 50K ohm; Lo-Z 500/600 ohm with TL600 xfmr; Bridging input 1:1 with TL 100 xfmrCONTROLS AND INDICATORS Level control, illuminated power switch, speech filtersOUTPUT LOADS (Const. Volt.) 25V CT, 25V, 7OV, 11OVOUTPUT LOADS (Spkr. Imp.) 8 and 16 ohms 4, 8 and 16 ohms(See chart for other impedances) (See chart for other impedances)SEMICONDUCTORS 6 Transistors, 7 Diodes 10 Transistors, 6 DiodesPOWER CONSUMPTION I20VAC, 60Hz, 180 watts Rated 120VAC 60Hz, 360 watts Ratedoutput output120VAC 60Hz, 25 watts Quiescent 120VAC 60Hz, 45 watts Quiescent(no output) (no output)48-56 VDC, 3 Amp Rated 48-56 VDC, 6 Amps Ratedoutput output48-56 VDC, 350 mA Quiescent 48-56 VDC, 600 mA Quiescent(no output) (no output)AC Circuit BreakerOVERLOAD PROTECTION Thermal Circuit BreakerTransient Protection DiodesDIMENSIONS 3.1” x 8.5” x 14” (8 x 21.5 x 36 cm)WEIGHT 18% lbs. (8.40 kg.)5.25” x 8.5” x 15” (13 x 21.5 x 38 cm)27 lbs. (12.3 kg.)Printed in USA 8111 54469148RadioFans.CN 收音机爱 好者资料库COMPANION UNITS AND ACCESSORIESModelCAMCDMCSMCFC-1RPK-37TL100TL600Description and InputsMixer-Preamplifier, 4 Hi-Z/Lo-Z Bal MIC, 1 AUXMixer-Preamplifier, 6 Lo-Z Bal MICStudio Mixer, 4 Lo-Z Bal MIC2/ 3 Octave EqualizerRack Mounting Kit 19” x 5” (48.26cm x 17.78cm; mounts 2 units)1: 1 Bridging Input TransformerLine Input Transformer, plug-in, 500/600-ohmimpedanceHigh impedance inputThe amplifier can be driven to full output from any sourcedeveloping 200 mV across one of the Hi-Z inputs. Wire a single-conductor, low-capacity shielded input cable to a standardphono plug (Cinch 18A, or equivalent) and connect to one of theHi-Z jacks on the rear of the chassis. Amplifiers may also beconnected in parallel by connecting a patch cord from Hi-Zinput to Hi-Z input of the amplifiers without loss of gain.Low impedance inputThe amplifier will match a low-impedance (500/600 ohm)source if a Bogen Model TL-600 transformer is installed insocket Xl on the circuit board. Connect a twisted, shielded pair(Bogen BB-8450, or equiv.) input cable to the BAL INPUTLOW Z terminal strip on the rear of the unit. Use the twooutside terminals on the strip for input and connect the cableshield to the GND terminal. If an unbalanced input is required,connect a jumper from the GND terminal to an adjacent inputterminal.CA UTIONRemove all power from unittransformers.before installingOUTPUTTERMINALSTRIP OFDRIVERAMPLIFIERn74-0736-AAT 70V RI - IOK, WA T 25V RI = 3.3K,WFigure 1 -Input from another amplifierBalanced bridging inputThe inputs for two or more amplifiers may be paralleledwithout loss of gain. To do this, install a Bogen Model TLlOOtransformer in socket Xl. Connect the 6OOa source to the BALLOW Z terminal strip on the rear of the unit. Use the twooutside terminals on the strip and connect the cable shields tothe GND terminal. If an unbalanced input is required, connect ajumper from the GND terminal to an adjacent input terminal.Input from another amplifierThe amplifier can be driven from a standard public addressamplifier that provides a 25-volt or 70-volt constant voltageoutput. To do this, connect the output of the amplifier to one ofthe Hi-Z INPUT jacks via a resistor network (see figure 1). Theresistors shown in figure 1 are in addition to the normalloudspeaker load on the output of the public address amplifier.OUTPUTCONNECTIONSCA UTIONBe sure to foIlow 1ocaI electrical codes whenconnecting amplifier output.A variety of outputs is provided from the amplifier, eitherbalanced or unbalanced. Refer to Table 1 for appropriateconnections. Generally, the ground link does not need to beconnected unless an unbalanced output is especially desired.TABLE 1- Output Connections*110V 2607ov 83.350V 4245V -32.5V-31v 1625v 8to 10.5* 13v 2.812.5V 2.5*Unbalanced output only*Disconnect link between COM and GNDOUTPUTIMPEDANCE (ohms)VOLTAGE MT 60A MT 125B11254020168to 10-4 to 51.41.251 2 3 4 5 6 7*JUMPER1 to3OUTPUT2-7OUTPUT 3-7 5-7 36 4-6 3-6 3-5 l-2 342RadioFans.CN 收音机爱 好者资料库Figure 2 -External level control for amplifiers70V constant-voltage outputFor 70V constant voltage operation, connect the speakerleads to the 70V and COM terminals on the rear of the unit. Ifgrounding is required, connect the link from COM to GND.25V constant-voltage outputFor 25V constant-voltage unbalanced operation, connect thespeaker leads to 25V and COM, leaving the link connectedbetween COM and GND. For balanced operation, open the linkbetween COM 1 and GND. If the output transformer center tapmust be grounded, connect a jumper between 25VCT and GND.CONNECTING AMPLIFIERS IN SERIESCAUTIONConnect only amplifiers of the same model inseries; do not mix different amplifier types.Bogen MTl25B or MT60A amplifiers may be connected inseries to increase total power output where absolutely necessaryto a single speaker line. Typical output connections are shown inTable 2. Note: GND straps on all except AMP I must be opened.Input connectionsIf the amplifier Hi-Z inputs are being driven directly, simplyparallel the amplifier Hi-Z inputs with a phono patch cord, andconnect the input line to one amplifier. When a balanced inputtransformer is being used, parallel the inputs at the screwterminals.Level control adjustmentIt is extremely important that the amplifiers have the samegain and produce equal power output. This adjustment is mosteasily accomplished by setting both amplifier level controls tomaximum and then providing an external gain control as shownin figure 2. Make sure speech filter switches are in the sameposition. If an external control cannot be provided, amplifiergain must be set with the use of an external tone source,adjusting the amplifiers to produce the same output with inputsparalleled. Always keep level controls at approximately thesame position even when setting up the amplifiers.CONNECTING AMPLIFIERS IN PARALLELIt is not recommended that amplifiers be connected inparallel. However, this is sometimes unavoidable. If it isnecessary to connect amplifiers in this configuration, consultour Engineering Department for instructions.POWER CONNECTIONSThe booster amplifier may be operated from 120VAC or 48Vto 56VDC.TABLE 2- Amplifier Series ConnectionNo. ofAmplfs.23222MT60A 18OW, 28aMTq;SB375w, 13L?MT60A 120W, 5.2aMT?25B250W, 2.5aMT60A 120W, 12051MT?25B25OW, 58aMT125B 250W 2oaoutput7ov7ov25v120v7ovConnectionsAMP 1 AMP 2+ OUTAMP 1 AM P 2 AMP 3opooooyo= 70Vooyopoo3 Z5V WINDINGS IN SERIES. O U TAMP 1 AMP 20 0 0 0 0“p?=, 25V+ OUTAMP 1 AMP 2?-. 120Vb OUTAMP 1 AMP 2000 0 00 P 7 o vb OUT3Thermal breakerIf the thermal breaker opens, there will be no audio outputbut the AC power lamp will remain on. Wait approximately fiveminutes for the breaker to reset. If the breaker resets and thenopens again, investigate the cause of the high temperatureoverload. This may be due to improper connections at theoutput terminals or to excessive environmental heat withinadequate ventilation. The thermal breaker will open when thetemperature at any one of the output transistors is excessive.Figure 3 -DC connections120VAC sourceConnect the AC power cord to a 12OVAC source. Use a 3-wire receptacle with the center pin connected to earth ground.48V-56VDC sourceConnect the amplifier to a DC source capable of deliveringpower indicated in the Technical Specifications table. Apolarized plug is supplied with the amplifier for making DCconnections. Connect DC cable to source, making certain toobserve proper polarity. An isolation diode should be used inseries with the DC supply as in figure 3.OPERATIONVOLUME CONTROLA volume control located on the rear of the unit is usedprimarily to compensate for variations in preamplifier outputlevels. The VOLUME control permits the gain of the amplifierto be preset so that the preamplifier volume control may beoperated near the center of its range, rather than at an extrememaximum or minimum. The VOLUME control is a screwdriveradjustment which needs to be set only once for any givenpreamplifier input.DC POWER OPERATIONWhen the amplifier is operated from a DC power source, theAC power switch and AC power indicator lamp will beinoperative. Turn the amplifier on and off from the powerswitch on the DC power supply or by inserting and removing theDC power leads on the rear of the unit.AC OPERATIONThere are two overload protective devices used with ACoperation, the circuit breaker and the temperature overloadthermal breaker.AC circuit breakerIf the circuit breaker opens, the AC power lamp will go outand the amplifier will have no output. Set the AC power switchto off and momentarily depress the red button on the circuitbreaker to reset it. Return the AC power switch to on. If thebreaker trips again, do not attempt to reset it but have thetrouble investigated by a qualified technician.MAINTENANCECA UTIONThere are no user-replaceable parts within theunit. Have all internal servicing done by aqualified technician.BOGEN SERVICEWe are interested in your Bogen equipment for as long as youhave it. If trouble ever develops, do not hesitate to ask ouradvice or assistance. Information can be obtained by writing toService Department, Bogen Division, P.O. Box 500, Paramus,N.J. 07652.When communicating with us, give the model and seriesdesignation of your unit. Describe the difficulty and includedetails on the electrical connections to and the types ofassociated equipment, such as preamplifier, speakers, etc. Wewill send you service information if the trouble appears simple.If the trouble requires servicing, we will send you the name andaddress of the nearest authorized Bogen service agency.Before returning any equipment to Bogen, contact the BogenService Department at the above address. If you do ship theunit, pack it carefully to avoid damage in transit. Send the unitfully insured and prepaid. It will be promptly repaired andreturned to you freight collect.REPLACEMENT PARTSMost components used in the amplifier are standard partsavailable through reputable parts suppliers. The parts listedhere may be obtained from Bogen distributors, service agenciesor directly from the factory. When ordering a part, specify thepart number and the description of the part as listed. Specify themodel of the unit and give the series designation, which is a letterfollowed by numbers, stamped on the chassis. For parts oncircuit boards, also give the component board assemblynumber, which begins with “45”.When replacing transistors, use those made by the manu-facturers specified. Transistors from other suppliers may not besatisfactory. Certain resistors must be Allen-Bradley. These aredesignated by “AB” on the schematic diagram.Replacing transistorsIf a transistor must be unsoldered for testing or replacement,be certain to remove all power from the unit to prevent possiblevoltage transients in the circuit which might damage thetransistor. To prevent overheating the transistor when solderingor unsoldering a lead, grip the lead between the point of heatand the case with pliers or tweezers. These will act as a heat sinkto conduct heat away from the transistor. Do not bend atransistor lead closer than 1 / 16” from the transistor case.4Power transistors must be properly mounted to insure goodheat dissipation. Make certain there is no foreign matter on thecontact surfaces between the transistor and the heat sink andbrush a thin coating of heat transfer compound (such as DowCorning No. 340 Compound silicon grease) on both surfaces.Similarly coat any insulators used between the transistor andthe heat sink and secure the transistor firmly to the heat sink.SchematicRef. Part No. DescriptionChassisCl01Cl02Cap, elect, 8800 F, 75V (MT-125B)Cap, elect, 13,000 F, 4OV (MT-125B)C20179-l 18-00479-l 18-00279-509-05sCapacitor, electrolytic, 6000 F, 75V(MT-6OA)C20279- 118-006Cap, elect, 5000 F, 50V (MT-60A)CB20194-0017-09 Circuit breaker, hold, 1.65ACB102CR101CR202,203CR102LlOlQIOI, 10294-0017-1894-0014-0796-52024 1(MT-6OA)Circuit breaker, 3.9A (MT-125B)Thermal breaker, 105CDiode, HVR396-5241-0196-5373-0195-5173-0196-5385-01Diode, 300 piv 3A (MT-60A)Bridge rectifier, 35A (MT-125B)Coil, .5 HTransistor, 2N3055H RCA(MT-60A) orQ101-106 96-5385-01Transistor, 2N3055H RCA(MT-125B)R204 76-114-101Resistor, .1 ohm, 5W (MT-60A)R102, 103,105, 106R104, 107SlOlT201TlOlT202T102FlOlFlOl76-l 14-09976-l 14-10781-100-00183-755-00083-794-00083-450-00083-454-00094-0005- 1894-0005-20Resistor, .22 ohm, 5W (MT-125B)Resistor, 3.3 ohm, 5W (MT-125B)Switch, powerTransformer, power (MT-6OA)Transformer, power (MT-125B)Transformer, output (MT-6OA)Transformer, output (MT-125B)Fuse, 3A slo-blo (MT-60A)Fuse, 6A slo-blo (MT-125B)P.C. board-c2C4c9Cl0CR1-4;:8R3R4R8Rll45-7084-01 Board assembly (MT-125B)45-7048-01Board assembly (MT-60A)79-5 12-040Capacitor, tantalum, 6.8 F, 35V79-008-065Cap, electrolytic, 10 F, 63V79-008-062Cap, elect, 100 F, 50V79-l 12-001Cap, elect, 500 F, 65V96-5333-01Diode, 400 piv 1A 96-5321-01Transistor, MPS-676796-5365-o 1Transistor, MPS-A5696-5316-01Transistor, (2N6107)96-5327-01Transistor, (2N6292)77-001-743Control, 200 kohm, screw-adjust75-l 54-304Resistor, 300 kohm, 1/4W, 1%75-154-104Resistor, 100 kohm, 1/4W, 1%75-154-124Resistor, 120 kohm, 1/4W, 1%76-520-680Resistor, 68 ohm, 1/2W, 5%, fireretardantR16, 1776-107-096 Resistor, .82 ohm, 2WR20 76-l 14-101Resistor, .l ohm, 5W (MT60A)Sl 8 I-003-067Switch, slide DPDT