HarmanKardon-AVR154-avr-sm维修电路原理图.pdf

harman/kardon AVR154 AVR154 5 X 30W 5.1 CHANNEL A/V RECEIVER SERVICE MANUAL CONTENTS ESD WARNING.2 LEAKAGE TESTING.3 BASIC SPECIFICATIONS.4 PACKAGING.5 FRONT PANEL CONTROLS.6 REAR PANEL CONNECTIONS.8 REMOTE CONTROL FUNCTIONS.10 CONNECTIONS/INSTALLATION.13 OPERATION.24 TROUBLESHOOTING GUIDE.29 REMOTE & PROCESSOR RESETS.30 DISASSEMBLY.31 UNIT EXPLODED VIEW.32 EXPLODED VIEW PARTS LIST33 AMP BIAS ADJUSTMENT.34 BLOCK DIAGRAM.35 PCB DRAWINGS36 ELECTRICAL PARTS LIST.42 SEMICONDUCTOR PINOUTS.71 SCHEMATICS.132 WIRING DIAGRAM.140 harman/kardon, Inc. 250 Crossways Park Dr. Released 2008 Woodbury, New York 11797 Rev0 5/2008 Discontinued XXXX RadioFans.CN 收音机爱 好者资料库Eachprecautioninthismanualshouldbefollowedduringservicing.Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in theparts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptablyinsulated from the supply circuit before retuming the product to the customer.Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are calledElectrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors andsemiconductor chip components.The following techniques should be used to help reduce the incidence of component damage caused by static electricity.1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge onyour body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device,which should be removed for potential shock reasons prior to applying power to the unit under test.2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, toprevent electrostatic charge build-up or exposure of the assembly.3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate electrical chargessufficient to damage ES devices.5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacementES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.)7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to thechassis or circuit assembly into which the device will be installed.Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing togetheror your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.CAUTION :AVR154 harman/kardonharman/kardon RadioFans.CN 收音机爱 好者资料库2SAFETY PRECAUTIONSThe following check should be performed for the continuedprotection of the customer and service technician.LEAKAGE CURRENT CHECKMeasure leakage current to a known earth ground (waterpipe, conduit, etc.) by connecting a leakage current testerbetween the earth ground and all exposed metal parts of theappliance (input/output terminals, screwheads, metaloverlays, control shaft, etc.). Plug the AC line cord of theappliance directly into a 120V AC 60Hz outlet and turn theAC power switch on. Any current measured must not exceedo.5mA.ANY MEASUREMENTS NOT WITHIN THE LIMITSOUTLINED ABOVE ARE INDICATIVE OF APOTENTIAL SHOCK HAZARD AND MUST BECORRECTED BEFORE RETURNING THE APPLIANCETO THE CUSTOMER.DeviceundertestTest allexposed metalsurfacesAlso test withplug reversed(Using AC adapterplug as required)AC Leakage TestLeakagecurrenttesterReading shouldnot be above0.5mAEarthgroundAVR154 harman/kardonharman/kardon 3AVR 154 TECHNICAL SPECIFICATIONSAudio SectionStereo Mode Continuous Average Power (FTC)40 Watts per channel, 20Hz20kHz, 0.07% THD, both channels driven into 8 ohmsFive-Channel Surround Modes Power per Individual ChannelFront L&R channels:30 Watts per channel 0.07% THD, 20Hz20kHz into 8 ohmsCenter channel:30 Watts 0.07% THD, 20Hz20kHz into 8 ohmsSurround (L & R Side) channels:30 Watts per channel 0.07% THD, 20Hz20kHz into 8 ohmsInput Sensitivity/ImpedanceLinear (High-Level)200mV/47k ohmsSignal-to-Noise Ratio (IHF-A)100dBSurround System Adjacent Channel SeparationPro Logic I/II 40dBDolby Digital (AC-3)55dBDTS55dBFrequency Response 1W (+0dB, 3dB)10Hz 130kHzHigh Instantaneous Current Capability (HCC)25 AmpsTransient Intermodulation Distortion (TIM)UnmeasurableSlew Rate40V/secFM Tuner SectionFrequency Range87.5108.0MHzUsable SensitivityIHF 1.3V/13.2dBfSignal-to-Noise RatioMono/Stereo 70/68dBDistortionMono/Stereo 0.2/0.3%Stereo Separation40dB 1kHzSelectivity400kHz, 70dBImage Rejection80dBIF Rejection90dBAM Tuner SectionFrequency Range5201720kHzSignal-to-Noise Ratio45dBUsable SensitivityLoop 500VDistortion1kHz, 50% Mod 0.8%Selectivity10kHz, 30dBVideo SectionTelevision FormatNTSCInput Level/Impedance1Vp-p/75 ohmsOutput Level/Impedance1Vp-p/75 ohmsVideo Frequency Response (Composite and S-Video)10Hz8MHz (3dB)Video Frequency Response (Component Video) 10Hz100MHz (3dB)HDMISwitchingGeneralPower RequirementAC 120V/60HzPower Consumption65W idle, 540W maximum (5 channels driven)Dimensions (Product)(Shipping)Width17-5/16 inches (440mm)22 inches (559mm) Height6-1/2 inches (165mm)10-1/2 inches (267mm) Depth15 inches (382mm)18-3/4 inches (476mm)(Product)(Shipping)Weight 20.5 lb (9.3kg)25.3 lb (11.5kg)Depth measurement includes knobs, buttons and terminal connections.Height measurement includes feet and chassis.All features and specifications are subject to change without notice.Harman Kardon and Logic 7 are trademarks of Harman International Industries, Incorporated, registered in the United States and/or other countries. Designed to Entertain is a trademark of Harman InternationalIndustries, Incorporated.Blu-ray Disc is a trademark of the Blu-ray Disc Association.Cirrus Logic is a registered trademark of Cirrus Logic, Inc.Dolby, Pro Logic and the double-D symbol are trademarks of Dolby Laboratories.Manufactured under license from Dolby Laboratories.Manufactured under license under U.S. Patent #s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;6,487,535; 7,003,467 & other U.S. and worldwide patents issued & pending. DTS, DTS Digital Surround,ES, and Neo:6 are registered trademarks and the DTS logos and Symbol are trademarks of DTS, Inc. 1996-2007 DTS, Inc.All rights reserved.HD-DVD is a trademark of the DVD Format/Logo Licensing Corporation (DVD FLLC).HDMI is a trademark or registered trademark of HDMI Licensing LLC.iPod is a trademark of Apple Inc., registered in the U.S. and other countries.SACD is a trademark of Sony Corporation.TiVo is a registered trademark of TiVo Inc.Please register your AVR 154 on our Web site at . Note:Youll need the products serial number.At the same time, you can choose to be notified about our new products and/or special promotions.AVR154 harman/kardonharman/kardon 4POLY BAGNODESCRIPTIONPARTS NO.Q,ty123456711CPB1061WPOLY BAG1. Instruction manual assy - AccessoriesSHEET GUIDE(QUICK START GUIDE)STAPLE108CPL0905CQE1A379Z311CARTAVR154CABR03P3CSA1A020ZREMOCON TRANSMITTER ASSYAM LOOP ANTENNABATTERY113CARD WARRANTYCQE1A172X1INSTRUCTION MANUALFM 1 POL ANT(UL)CQX1A1309ZCSA1A019Z11CARD WARRANTYSHEET GUIDE2BATTERY ASSY4REMOCONTRANSMITTER ASSY873AM LOOP ANTENNA ASSYMANUAL INSTRUCTION5FM 1 POLE ANT(UL)6STAPLESHEET,FRONT COVERCOVER BCOVER ABAG,POLYPAD, COVERCQE1A219ZCGR1A332H63CPS1A676CPB1A176ZCGR1A331H631 11111COVER ASSYCGRAVR154ZA154321COVER ASSY910IMAGE BROCHURES11HQE1A273Z1IMAGE BROCHURES119MANUAL ASSYBOX,OUT CARTON4512DESCRIPTIONNOCPS5A564CQXAVR154CPG1A854Z111Q,tyPARTS NO.CPS5A565SNOW,PAD(R)31SNOW,PAD(L)SET1A2. Package DrawingAVR154SNOW PAD (R)3BOX ,OUT CARTON54SNOW PAD (L)2MANUAL ASSY1AVR154AVR154AVR 154visit 58Main Power Switch:This mechanical switch turns the power supplyon or off. It is usually left pressed in (On position), and cannot be turnedon using the remote control.Standby/On Switch:This electrical switch turns the receiver on for playback, or leaves it in Standby mode for quick turn-on using thisswitch or the remote control.Power Indicator:This LED has four possible modes: Main Power Off: When the AVR is unplugged or the Main PowerSwitch is off, this LED remains unlit. Standby: This LED turns amber, indicating that the AVR is ready to be turned on. On: This LED turns white, and the AVR operates normally. Protect: If this LED ever turns red, turn off the AVR and unplug it.Check all speaker wires for a possible short. If none is found, bringthe unit to an authorized Harman Kardon service center for inspectionand repair before using it again.When the main power is turned off, the LED is dark and the receiverwont respond to any button presses.When the main power is turnedon, but before the Standby/On Switch is used, the LED turns amber toindicate that the receiver is in standby mode and is ready to be turnedon.When the receiver is turned on, the LED turns white.Source Select:Press this button to select a source device, which is a component where a playback signal originates, e.g., DVD, CD,cable TV, satellite or HDTV tuner.The sources name will appear in the Message Display.Volume Knob:Turn this knob to raise or lower the volume, which will be shown in decibels (dB) in the Message Display.Message Display:Various messages appear in this two-line displayin response to commands and changes in the incoming signal. In normal operation, the current source name and the analog or digitalaudio input assigned to it appear on the upper line, while the surroundmode is displayed on the lower line.When the on-screen display menusystem (OSD) is in use, the message OSD ON will appear to remind you to check the video display.Tuner Band:Press this button to select the tuner as the source, or to switch between the AM and FM bands.Tuning:Press either side of this button to tune a radio station.Tuning Mode:This button toggles between manual (one frequencystep at a time) and automatic (seeks frequencies with acceptable signalstrength) tuning mode. It also toggles between stereo and mono modeswhen an FM station is tuned.Preset Stations:Press this button to select a preset radio station.Headphone Jack:Plug a 1/4 headphone plug into this jack for private listening.Surround Mode:Press this button to select a surround sound (e.g., multichannel) mode group. Choose from the Dolby modes,DTS modes, Logic 7 modes, DSP modes or Stereo modes.Surround Select:After you have selected the desired surroundmode group, press this button to select a specific mode.Analog Audio,Video and Digital Audio Inputs:Connect asource component that will only be used temporarily, such as a cameraor game console to these jacks. Use only one type of audio and onetype of video connection.Speaker/Channel Input Indicators:The box icons indicatewhich speaker positions you have configured (see the Initial Setup section), and the size (frequency range) of each speaker.When a digitalaudio input is used, letters will light inside the boxes to indicate whichchannels are present in the incoming signal.Remote IR Sensor:This sensor receives infrared (IR) commandsfrom the remote control. It is important to ensure that it is not blocked.If covering the sensor is unavoidable, such as when the AVR 154 isplaced inside a cabinet, you may use an optional Harman Kardon HE 1000, or other infrared receiver, with an IR emitter (“blaster”) placed directly over this sensor.FRONT-PANEL CONTROLSAVR154 harman/kardonharman/kardon 69SurroundModeTuningPreset StationsSurroundSelectTuner BandTuning ModeSourceSelectHeadphoneJackDigitalAudio Inputs(Optical 3 andCoaxial 3)Video 3Video InputsVideo 3Analog AudioInputsPowerIndicatorMain PowerSwitchStandby/OnSwitchVolumeRemote IR SensorMessage DisplaySpeaker/ChannelInput IndicatorsNOTE: To make it easier to follow the instructions throughout the manual that refer to this illustration, a copy of this page may be downloaded from the Product Support section .AVR154 harman/kardonharman/kardon 710REAR-PANEL CONNECTIONSAM and FM Antenna Terminals:Connect the included AM andFM antennas to their respective terminals for radio reception.Front, Center and Surround Speaker Outputs:Use two-conductor speaker wire to connect each set of terminals to the correctspeaker. Remember to observe the correct polarity (positive and negativeconnections).Always connect the positive lead to the colored terminalon the receiver and the red terminal on the speaker. Connect the negativelead to the black terminal on both the receiver and the speaker. See theConnections section for more information on connecting your speakers.Subwoofer Output:If you have a powered subwoofer with a line-level input, connect it to this jack.Video 1,Video 2 and DVD Audio/Video Inputs:These jacksmay be used to connect your video-capable source components (e.g.,VCR, DVD player, cable TV box) to the receiver.NOTE: If a source is HDMI-capable, it is preferable to connect itto one of the AVRs HDMI Inputs. If HDMI is not available on thesource, then select one of the following types of video connectionfor each source device, in order of preference: componentvideo, S-video or composite video.See the Connections section for more information on audio and videoconnection options.Video 1 Audio/Video Outputs:These jacks may be used to connect your VCR or another recorder.Composite and S-Video Monitor Outputs:If any of yoursources use composite or S-video connections, connect one or both of these monitor outputs to the corresponding inputs on your televisionor video display.CD and Tape Audio Inputs:These jacks may be used to connectaudio-only source components (e.g., CD player, tape deck). Do not connect a turntable to these jacks unless you are using it with a phonopreamp.Tape Outputs:These jacks may be used to connect a CDR oranother audio-only recorder.Coaxial and Optical Digital Audio Inputs:If your source has a compatible digital audio output, connect it to one of these jacksfor improved audio performance. Use only one type of digital audio connection for each source.Coaxial Digital Audio Output:If a source is also a digital audiorecorder, connect the coaxial digital audio output to the recorders coaxial digital input.AUX Input:Enjoy audio from an iPod (not included), CD player orother portable player by connecting its headphone jack