Yamaha-HTR3063-avr-sm 维修电路原理图.pdf

1 0 11 6 7SERVICE MANUALIMPORTANT NOTICEThis manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.It has been assumed that basic service procedures inherent to the industry, and more specifi cally YAMAHA Products, are already known and understood by the users, and have therefore not been restated.WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specifi ed. For these reasons, we advise all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representative.IMPORTANT: The presentation or sale of this manual to any individual or fi rm does not constitute authorization, certifi cation or recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and specifi cations are subject to change without notice or obligation to retrofi t. Should any discrepancy appear to exist, please contact the distributors Service Division.WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit. CONTENTSTO SERVICE PERSONNEL .2FRONT PANELS .34REAR PANELS .510REMOTE CONTROL PANELS .11SPECIFICATIONS .1216INTERNAL VIEW .17DISASSEMBLY PROCEDURES .1820UPDATING FIRMWARE .2123SELF-DIAGNOSTIC FUNCTION .2448DISPLAY DATA .4950IC DATA .5162BLOCK DIAGRAM .63PRINTED CIRCUIT BOARDS .6477PIN CONNECTION DIAGRAMS .78SCHEMATIC DIAGRAMS .7987REPLACEMENT PARTS LIST .8997REMOTE CONTROL .98102ADVANCED SETUP . 103104AV RECEIVER10.03RX-V367/HTR-3063Copyright 2010 All rights reserved.This manual is copyrighted by YAMAHA and may not be copied orredistributed either in print or electronically without permission.When the following parts are replaced, the model name and the destination MUST be written to the back-up IC (EEPROM: IC222 of the DIGITAL P.C.B.) to have proper operation. (See No. 22 SOFT SWITCH menu of the self-diagnostic function.) EEPROM (IC222) of DIGITAL P.C.B. DIGITAL P.C.B.P.O.Box 1, Hamamatsu, JapanRX-V367/HTR-3063This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive harm.DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHATSOEVER!Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor!If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food.1. Critical Components InformationComponents having special characteristics are marked and must be replaced with parts having specifications equal to those originally installed.2. Leakage Current Measurement (For 120V Models Only)When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated from supply circuits. Meter impedance should be equivalent to 1500 ohms shunted by 0.15 F.All of the P.C.B.s installed in this unit and solder joints are soldered using the lead free solder.Among some types of lead free solder currently available, it is recommended to use one of the following types for the repair work. Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc + bismuth)Caution:As the melting point temperature of the lead free solder is about 30C to 40C (50F to 70F) higher than that of the lead solder, be sure to use a soldering iron suitable to each solder. TO SERVICE PERSONNEL Leakage current must not exceed 0.5mA. Be sure to test for leakage with the AC plug in both polarities.WARNING: CHEMICAL CONTENT NOTICE!About lead free solderFor U model“CAUTION”“F1501: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 6A, 125V FUSE.”For C modelCAUTIONF1501: REPLACE WITH SAME TYPE 6A, 125V FUSE.ATTENTIONF1501: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE 6A, 125V.WALLOUTLETEQUIPMENTUNDER TESTAC LEAKAGETESTER OREQUIVALENTINSULATINGTABLE2RX-V367/HTR-3063RX-V367/HTR-3063 FRONT PANELS3RX-V367/HTR-3063RX-V367/HTR-3063Top viewFront viewRX-V367 (R, K, A, B, G, F, L models)RX-V367 (U, C, T models)RX-V367 / HTR-30634RX-V367/HTR-3063RX-V367/HTR-3063HTR-3063 (U, C, T models)HTR-3063 (R, K, A, G, F, L models) REAR PANELS5RX-V367/HTR-3063RX-V367/HTR-3063RX-V367 (U model)RX-V367 (C model)RX-V367 (R model)6RX-V367/HTR-3063RX-V367/HTR-3063RX-V367 (T model)RX-V367 (K model)RX-V367 (A model)7RX-V367/HTR-3063RX-V367/HTR-3063RX-V367 (B, G, F models)RX-V367 (L model)HTR-3063 (U model)8RX-V367/HTR-3063RX-V367/HTR-3063HTR-3063 (T model)HTR-3063 (C model)HTR-3063 (R model)9RX-V367/HTR-3063RX-V367/HTR-3063HTR-3063 (K model)HTR-3063 (A model)HTR-3063 (G, E, F models)10RX-V367/HTR-3063RX-V367/HTR-3063HTR-3063 (L model) REMOTE CONTROL PANELSSheet (T model)11RX-V367/HTR-3063RX-V367/HTR-3063RAV331(U, C models)RAV332(R, T, K, A, L models)RAV333(B, G, E, F models) SPECIFICATIONS Audio SectionMinimum RMS Output Power (Power Amp. Section)(1 kHz, 0.9 % THD)U, C models (8 ohms)FRONT L/R .100 W/chCENTER .100 WSURROUND L/R .100 W/chR, T, K, A, B, G, F, L models (6 ohms)FRONT L/R .100 W/chCENTER .100 WSURROUND L/R .100 W/chMaximum Power (JEITA) (1 kHz, 10 % THD, 6 ohms)R, T, K, L modelsFRONT L/R .135 W/chCENTER .135 WSURROUND L/R .135 W/chMax. Power Per Channel (1 kHz, 0.7 % THD, 4 ohms)B, G, F, L modelsFRONT L/R .120 W/chCENTER .120 WSURROUND L/R .120 W/chIEC Power (1 kHz, 0.9 % THD, 8 ohms) B, G, F, L modelsFRONT L/R .95 W/chDynamic Power Per Channel (IHF) (FRONT L/R drive)U, C models(8/6/4/2 ohms) .110/130/160/180 WR, T, K, A, B, G, F, L models (6/4/2 ohms) .105/130/150 WDynamic Headroom U, C models(8 ohms) .0.23 dBInput Sensitivity/Input ImpedanceAV5, etc. . 200 mV / 47 k-ohmsMaximum Input Signal (1 kHz, 0.5 % THD, Effect on)AV5, etc. .2.3 V or moreOutput Level/Output ImpedanceAUDIO OUT (REC) . 200 mV / 1.2 k-ohmsSUBWOOFER (2 ch STEREO and FRONT SP: Small) . 1 V / 1.2 k-ohmsHeadphone Jack Rated Output/ImpedanceAV5, etc. (1 kHz, 50 mV, 8 ohms) . 100 mV / 470 ohmsFrequency Response (10 Hz to 100 kHz)AV5, etc. to FRONT L/R .0 / -3.0 dBTotal Harmonic Distortion (1 kHz, 50 W)AV5, etc. (straight) to FRONT L/R SP OUTU, C models(8 ohms) .0.06 % or lessR, T, K, A, B, G, F, L models(6 ohms) .0.06 % or lessSignal to Noise Ratio (IHF-A Network)AV5, etc. (STEREO) (Input shorted) to SP OUT250 mV . 98 dB or moreResidual Noise (IHF-A Network)FRONT L/R SP OUT .150 V or lessChannel SeparationAV5, etc. (Input 5.1 k-ohms shorted, 1 kHz / 10 kHz) . 60 dB or more / 45 dB or moreVolume Control .MUTE / -80 dB to +16.5 dB / 0.5 dB stepTone Control CharacteristicsBASSBoost/Cut . 10 dB / 2 dB step / 50 HzTurnover frequency .350 HzTREBLEBoost/Cut .10 dB / 2 dB step / 20 kHzTurnover frequency .3.5 kHzFilter CharacteristicsFRONT, CENTER, SURROUND (H.P.F.) .fc=40/60/80/90/100/110/120/160/200 Hz, 12 dB/oct.SUBWOOFER (L.P.F.) .fc=40/60/80/90/100/110/120/160/200 Hz, 24 dB/oct. Video SectionComposite Video Signal Level .1 Vp-p / 75 ohmsComponent Signal LevelY .1 Vp-p / 75 ohmsPB/PR .0.7 Vp-p / 75 ohmsVideo Maximum Input Level (VIDEO COMV. OFF) .1.5 Vp-p or moreSignal to Noise Ratio (IHF) . 50 dB or moreMonitor Out Frequency Response Component video signal .5 Hz to 60 MHz, 3 dB FM SectionTuning RangeU, C models .87.5 to 107.9 MHzR, L models .87.5 to 108.0 / 87.50 to 108.00 MHzT, K, A, B, G, F models .87.50 to 108.00 MHz50 dB Quieting Sensitivity (IHF) (1 kHz, 100 % Mod.)Mono .3 V (20.8 dBf)Signal to Noise Ratio (IHF)Mono .74 dBStereo .69 dBHarmonic Distortion (1 kHz)Mono .0.3 %Stereo .0.3 %Antenna Input . 75 ohms unbalanced12RX-V367/HTR-3063RX-V367/HTR-3063Front viewTop view435 (17-1/8)315 (12-3/8)274 (10-3/4)170 (6-5/8)59(2-3/8)45(1-3/4)23(7/8)18(3/4)130 (5-1/8)21(7/8)151 (5-7/8)335 (13-1/4) 6050(2) DIMENSIONSUnit: mm (inch)Manufactured under license from Dolby Laboratories.“Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories.“SILENT CINEMA” is a trademark of Yamaha Corporation.“HDMI”, the “HDMI” logo and “High-Definition Multimedia Interface” are trademarks, or registered trademarks of HDMI Licensing LLC.“iPod” is a trademark of Apple Inc., registered in the U.S. and other countries. “iPhone” is a trademark of Apple Inc. Bluetooth is a registered trademark of the Bluetooth SIG and is used by Yamaha in accordance with a license agreement.DTS and DTS Digital Surround are registered trademarks and the DTS logos and Symbol are trademarks of DTS, Inc. U .U.S.A. model C .Canadian modelR .General model T.Chinese modelK .Korean model A .Australian modelB .British model G .European modelF. Russian modelL.Singapore model AM SectionTuning RangeU, C models .530 to 1,710 kHzR, L models .530 to 1,710 / 531 to 1,611 kHzT, K, A, B, G, F models .531 to 1,611 kHzAntenna Input .Loop antenna GeneralPower SupplyU, C models .AC 120 V, 60 HzR model .AC 110-120/220-240 V, 50/60 HzT model .AC 220 V, 50 HzK model .AC 220 V, 60 HzA model .AC 240 V, 50 HzB, G, F models .AC 230 V, 50 HzL model .AC 220-240 V, 50/60 HzPower ConsumptionU, C models .250 W / 320 VAR, T, K, A, B, G, F, L models .250 WStandby Power ConsumptionU, C, T, K, A, B, G, F models .0.5 W or lessR model .1.0 W or lessMaximum Power Consumption .440 WDimensions (W x H x D) .435 x 151 x 315 mm (17-1/8 x 5-7/8 x 12-3/8)Weight .7.5 kg (16.5 lbs.)FinishRX-V367T model .Gold colorU, C, R, T, K, A, B, G, F, L models . Black colorR, G, F, L models .Titanium colorSilver colorHTR-3063T model .Gold colorU, C, R, T, K, A, G, F, L models . Black colorR, G models .Silver colorAccessoriesRemote control .x 1Batteries (R03, AAA, UM-4) .x 2Indoor FM antenna (1.4 m) .x 1AM loop antenna (1.0 m) .x 1Optimizer microphone (6.0 m) .x 1Sheet (T model) .x 1* Specifications are subject to change without notice.13RX-V367/HTR-3063RX-V367/HTR-306314RX-V367/HTR-3063RX-V367/HTR-3063MOVIEStandardSpectacleSci-FiAdventureDramaMono MovieSportsAction GameRoleplaying GameMUSICHall in MunichHall in ViennaChamberCellar ClubThe Roxy TheatreThe Bottom LineMusic VideoSTEREO2ch Stereo5ch StereoMUSIC ENHANCERStraight Enhancer5ch EnhancerSUR. DECODESurround Decoder*1STRAIGHT*1 Decode TypeDecode TypePro LogicPL II MoviePL II MusicPL II Game : Setting is possible only when Pro Logic II Music is selected using decode type.Decode Type Pro Logic II Music 選択時設定可Decode TypeDSP Level: -6dB to +3dBCenter Level: 0 to 100%Surround L Level: 0 to 100%Surround R Level: 0 to 100%Direct: Auto/OffEffect Level: High/LowPanorama: On/OffInitializeParameterCategoryProgram SELECT MENUSound field parameters15RX-V367/HTR-3063RX-V367/HTR-3063MAIN MENUSUB-MENUPARAMETERVALUE INITIAL VALUE1 Speaker Setup1 ConfigSubwooferYes / NoneFront speakerSmall / LargeCenter speakerNone / Small / LargeSurround speaker L/RCrossover40 / 60 / 80 / 90 / 100 / 110 / 120 / 160 / 200 HzSubwoofer PhaseNRM / REVExtra BassOn / Off2 LevelFL (Front speaker L)-10.0 to +10.0 dB, 0 dB, 0.5 dB stepFR (Front speaker R)C (Center speaker)-10.0 to +10.0 dB, -1.0 dB, 0.5 dB stepSL (Surround speaker L)SR (Surround speaker R)SWFR (Subwoofer)-10.0 to +10.0 dB, 0 dB, 0.5 dB step3 DistanceUnitmeters (m) / feet (ft)Front L0.30 to 24.00 m, 3.00 m, 0.1 m step1.0 to 80.0 ft, 10.0 ft, 0.5 ft stepFront RCenter0.30 to 24.00 m, 2.60 m, 0.1 m step1.0 to 80.0 ft, 8.5 ft, 0.5 ft stepSur. L0.30 to 24.00 m, 2.40 m, 0.1 m step1.0 to 80.0 ft, 8.0 ft, 0.5 ft stepSur. RSWFR0.30 to 24.00 m, 3.00 m, 0.1 m step1.0 to 80.0 ft, 10.0 ft, 0.5 ft step4 EqualizerEQ Type SelectGEQ / OffGEQ* “GEQ” is available only when “EQ Type Select” is set to “GEQ” .Front L63 Hz | 0 dB-6.0 to +6.0 dB, 0 dB, 0.5 dB stepFront R160 Hz | 0 dBCenter400 Hz | 0 dBSur. L1 kHz | 0 dBSur. R2.5 kHz | 0 dB6.3 kHz | 0 dB16 kHz | 0 dB5 Test ToneOff / On2 Sound Setup1 LipsyncHDMI AutoOff / OnAuto0 to 240 ms, 1 ms stepManual0 to 240 ms, 0 ms, 1 ms step2 Adaptive DRCAuto / Off3 D.RangeMax / STD / Min4 Max Volume-30.0 to +15.0 dB / +16.5 dB (Maximum volume), +16.5 dB, 5.0 dB step5 Init. VolumeOff, Mute, -80 dB to +16.5 dB Off, 0.5 dB step6 HDMI Audio OutAmp / TV / Amp+TV3 Function Setup1 Input RenameInput is possible to 9 charactersInput possible Character typeCapital : A to ZSmall : a to zFigure : 0 to 9Symbols : # * + , - etc.Space2 Auto Power DownOff / 4 hours / 8 hours / 12 hours3 Dimmer-4 to 0, 0 SET MENU TABLE16RX-V367/HTR-3063RX-V367/HTR-3063MAIN MENUSUB-MENUPARAMETERVALUE INITIAL VALUE4 DSP ParameterMOVIE Standard2, 9SpectacleSci-FiAdventureDramaMono MovieSportsAction GameRoleplaying GameMUSIC Hall in Munich2, 9Hall in ViennaChamberCellar ClubThe Roxy TheatreThe Bottom LineMusic VideoSTEREO 2ch Stereo6, 95ch Stereo3, 4, 5, 9MUSIC ENHANCER Straight Enhancer7, 95ch Enhancer7, 9SUR. DECODE Sur. Decoder1, 8, 9STRAIGHT5 Memory GuardOff / On1Decode TypePro Logic, PL II Movie, PL II Music, PL II Game2DSP Level-6 to +3 dB, 0 dB3Center Level4Surround L Level0 to 100 %, 100 %5Surround R Level6DirectAuto / Off7Effect LevelHigh / Low8PanoramaOff / On9InitializeOPERATION (3) P.C.B.MAIN (3) P.C.B. (R model)MAIN (1) P.C.B.AM/FM TUNERDIGITAL P.C.B.MAIN (2) P.C.B.OPERATION (4) P.C.B.MAIN (4) P.C.B.OPERATION (9) P.C.B. OPERATION (2) P.C.B.OPERATION (8) P.C.B.POWER TRANSFORMEROPERATION (7) P.C.B.OPERATION (1) P.C.B.OPERATION (6) P.C.B.OPERATION (5) P.C.B.123456789101112131415169111612108113141535246717RX-V367/HTR-3063RX-V367/HTR-3063 INTERNAL VIEWCableRemove CB136UnlockedCableConnect CB136LockedConnected Top cover Front panel unitHook CB166 CB193 CB221 CB13618RX-V367/HTR-3063RX-V367/HTR-3063Fig. 1 DISASSEMBLY PROCEDURES(Remove parts in the order as numbered.)Disconnect the power cable from the AC outlet.1. Removal of Top Covera. Remove 5 screws () and 4 screws (). (Fig. 1)b. Slide the top cover rearward to remove it. (Fig. 1)2. Removal of Front Panel Unita. Remove 7 screws (). (Fig. 1)b. Remove CB166, CB193 and CB221. (Fig. 1)c. Unlock and remove CB136. (Fig. 1)d. Release hook and then remove the front panel unit. (Fig. 1)DIGITAL P.C.B.DIGITAL P.C.BOPERATION (4) P.C.B.OPERATION (4) P.C.B.MAIN (1) P.C.B.CB222CB223CB262CB22CB191CB192CB195CB196CB264CB263CB21? ?(U, C models)19RX-V367/HTR-3063RX-V367/HTR-3063Fig. 3Fig. 23. Removal of DIGITAL P.C.B.a. Remove CB222223 and CB262. (Fig. 2)b. Remove 2 screws (U, C models)/1 screw (R, T, K, A, B, G, L models) () and 5 screws (). (Fig. 3)c. Remove the DIGITAL P.C.B. which is connected directly to the OPERATION (4) P.C.B. with boa