Maxon CM-10 Schema and User Manual.pdf

User Manual CM10 Page 2 of 14 Contents Specification3 Control and Operation .4-5 Installation 6 Installation of Main Unit 6 Installation of Antenna .6 Operational Test 7 Frequency Bands Table 7 Frequency Band Selection 7 Reset .8 Table of Restrictions .9 Updated Information on National Restrictions .10 Diagrams .11-13 Decleration of Conformity .14 User Statement .15 C C Co o on n nt t te e en n nt t ts s s User Manual CM10 Page 3 of 14 Specification GENERAL Channels. 40 Ch AM/FM 4W Frequency Range.26.565 to 27.99125 MHz Frequency Control.PLL Operating Temperature Range.-10 / +55C DC Input Voltage.13.2 V DC 15% Size.180(L) X 35(H) X 140(D) mm Weight.750 g RECEIVER Receiving System.Dual Conversion Super Heterodyne Intermediate Frequency.1st IF: 10.695 MHz, 2nd IF: 455 MHZ Sensitivity.0.5 V for 20 db SINAD in FM mode Audio Distortion.Less Than 8% 1 KHz Image Rejection.65 dB Adjacent Channel Rejection.65 dB Signal/ Noise Ratio.45 dB Current Drain at standby.150 mA Current Drain at maximum audio.820 mA TRANSMITTER Output Power.4W 13.2 V DC Modulation.FM: 1.8 KHz 0.2 KHz Frequency response.From 400 Hz to 2.5 KHz Output impedance.RF 50 ohm Unbalance Signal/ Noise Ratio.40 dB MIN Current Drain.1100 mA S S Sp p pe e ec c ci iif f fi iic c ca a at t ti iio on n on User Manual CM10 Page 4 of 14 Control during the frequency band selection process, the frequency band display will blink at a faster rate. 5) Press and hold the DN key to confirm and store the new selected frequency band code. User Manual CM10 Page 8 of 14 Reset To restore the original factory settings (CE frequency brand), follows the below process: 1) Turn the radio OFF. 2) Press and hold the DN key, then turn the radio ON using the OFF/VOLUME knob. 3) The CE frequency band code (code 06) will blink on the display for 3 seconds. R R Re e es s se et t et User Manual CM10 Page 9 of 14 Table of Restrictions on the Use of CB Transceivers The following information is only to be used as an indication. They are believed to be correct at the time of printing this manual. It is however the users responsibility to check that, in the country where radio is used, providing the regulations for the use of CB transceivers have not been modified. It is therefore suggested that the user contact the local dealer or local authority, in order to check the current regulations for the use of CB transceivers, before operating this product. The manufacturer does not accept any responsibility if the product is used in violation of the regulations of the country where the product is used. T T Ta a ab b bl lle e e o o of f f R R Re e es s st t tr r ri iic c ct t ti iio o on ns s ns User Manual CM10 Page 10 of 14 Updated information on National Restrictions BELGIUM, UK, SPAIN, SWITZERLAND In order to use this transceiver in Belgium, UK, Spain and Switzerland, users must have an individual licence. Users coming from abroad may freely use the radio in FM mode, while in order to use it in AM mode they must hold a licence issued in their country of residence. ITALY Foreigners arriving in Italy must get an Italian authorisation. AUSTRIA Austria does not allow using multi standard programmable CB radios. It is recommended that users carefully follow this directive and not to use the product in the Austrian territory. GERMANY Along some border areas in Germany, the radio can not be used as a base station from Channel 41 to channel 80. Refer to local authority (notification office) for details. U U Up p pd d da a at t te e ed d d I I In n nf f fo o or r rmm ma a at t ti iio o on n n o o on n n N N Na a at t ti iio o on n na a al ll R R Re e es s st t tr r ri iic c ct t ti iio o on n ns s s User Manual CM10 Page 11 of 14 Diagrams D D Di iia a ag g gr r ra a amm ms s s User Manual CM10 Page 12 of 14 D D Di iia a ag g gr r ra a am m ms s s User Manual CM10 Page 13 of 14 D D Di iia a ag g gr r ra a amm ms s s User Manual CM10 Page 14 of 14 U U Us s se e er r r S S St t ta a at t te e emm me en nt t ent