Vertex_FTL-1011_2011_7011_user.pdf

FM Land Mobile Transceivers Operating Manual YAESU MUSEN CO., Ltd. CP.0. Box 1500, Tokyo, Japan YAESU U.S.A. 17210 Edwards Rd., Cerritos, CA 90701, U.S.A. YAESU EUROPE B.V. Snipweg 3,1118AA Schiphol, The Netherlands Congratulations! You now have at your fingertips a valuable communications tool - a Yaesu two-way radio! Rugged, reliable and easy to use, i your Yaesu radio will keep you in constant touch with your I colleagues for years to come, with negligible maintenance down time. Please take a few minutes to read this manual carefully. The information presented here will allow you to derive maximum performance from your radio. After reading it, keep the manual handy for quick reference, in case questions arise later on. Were glad you joined the Yaesu team. Call on us any time, because our business is communications. Let us help you get your message across. NOTICE There are no user-servicable points inside this trans- ceiver. All service jobs must be referred to your Authorized Service Center or Network Administrator. FTH-1011, FTL-2011 VHF and FTL-7011 UHF FM Land Mobile Transceivers The 60-watt VHF Low-Band FTL-1011, 40-watt VHF High- Band FTL-2011 and 25-watt UHF FTL-7011 are rugged, full-fea- tured FM transceivers designed for flexible mobile and base station business communications. Each model is available with either a -4 or -12 suffix, with a capacity of either 4 or 12 channels, respectively . Reliability is assured by a highly integrated surface mount circuit design and a die-cast aluminum chassis. Important chan- nel frequency data is stored in EEPROM, and is easily program- mable by dealers using a personal computer and the Yaesu FRB-2 Interface Box, T9101410 Cable and CE-5 or VPL-1 Soft- ware. Special features include a built-in CTCSS (Continuous Tone Coded Squelch System) and in the 12-channel versions, two sets of scanning channels, one set preselectable by the dealer and another operator selectable. The operator can select which set to scan, and also two priority channels. Dealers can program Busy Channel Lockout, transmitter time out timers and scan stop activities for talkback on the paused channel, priority channel or the home channel (on which scanning was initiated). Scanning is not provided in the 4-channel versions. Each transceiver is supplied with a mobile bracket and hand microphone. Options include the FP-711 Power Supply for op- eration from the AC mains, the FDS-1 Digitally Coded Squelch Unit and F2D-4 2-Tone Decoder programmable by your dealer. Please take a few minutes to read this manual carefully. The information presented will help you derive maximum perform- ance from the equipment. After reading, keep it handy near the radio for quick reference. Controls nal on the channel (the yellow MON indicator be lit). kou can get the same result without lifting the micro- xe, by pressing the MON button momentarily. To avoid listening lnecessary chatter, keep the microphone in its hanger, and press tne MON button when necessary to turn the yellow indicator off unless you want to listen to other calls. Holding the MON button for two seconds defeats not only coded squelch, but also the noise squelch, so background noise can be heard (the MON indicator blinks). This is useful for setting the vol- ume when no signals are present. Press MON momentarily to return the J to its prc ate (off, or steadily on). dica tor , , 7er quiet ignals Vertex FTL-1011, FTL-2011 t 3 FTL-7011 Operating Manual Setting the Volume If no signals are heard and the BUSYrrX indicator is not glowing green (so you can adjust the volume on a signal), press and hold the MON button for two seconds until a beep is heard and the yellow indicator above the button blinks. Then adjust the volume control for a comfortable level on a signal or background noise, Press MON again momentarily so the yellow indicator stops blinking. See the box on the previous page for more information on controlling the squelch system. Transmitting To transmit, wait until the BUSYrrX indicator is off (the channel is not in use), and press the PTT (Push-To-Talk) switch on the side of the microphone (the BUSYITX lamp glows red). While holding the PTT switch, speak across the face of the microphone in a clear, normal voice, and then release the PTT switch to receive. The box below describes some other features that may be programmed to affect your transmissions. Remaining instructions apply to 12-channel versions only. Scanning Four scanning modes are available when the SCAN button has been pressed. Oncea scan mode is selected, it remains selected If th out, yoL ting, a beep sc . * T . a momc )ur trans itter will e selecte 1 must lii beep sol xtt, and pecial . not acti . r d chann mit the 1t lnds ten the timt . . then prc Trans; s progra vate wh ,- I . .el has b c q t h of second: ?-out pel . . !ss it aga ock-out, ssed ud . . a CI Functions If yc mmed for busy channel 1 transm: en the PTT switch is pre: the BUSYlTX lamp is orr (to prevent interference to other stations). een programmed for atitolnafic time- your transmissions. While transmit- ; before time-out, and then another riod expires: the BUSYRX irdicator will turn orr ana transmission will cease. Release the MT, listen for in to res - ume trai nsmittin, Vertex FTL-1011, FTL-2011 -l.A p (p 1) t ? E (Scan Enable) Indic Jhen a channel number is displayed, either during manual ning) operation, lg is pau i indi- rs at the top of t be lit. TT at the nel has been seleLLCU LV VC IILLILLJed in uscl scalLlL11L6 llrvces (Ur and UP). If the P indicator is blinking nnel is the 1st (highest priority) channel for the UP mode. If tl )t blinking but steadily on, the channel is the 2nd priority C I I I I I . 30th priority channels serve as ordinary user-selected scan channels in the Ur mode. , the cha le P is nc . 1 1 P and E licate th (non- Vertex FTL-1011, FTL-2011 e resul page 12 Specifications General Frequency Range (version) FTL- 101 1: 37 - 48 MHz FTL-2011: 134 - 1601148 - 174 MHz (vers. A/C, resp.) FTL-7011: 400 - 440 MHz (A), 420 - 460 MHz (B), 450 - 490 MHz (D) or 480 - 5 12 MHz (F) N r . of Channels & Spacing 4 (-4 models), 12 (-12 models, 24 chs optional) 25-kHz spacing (12.5-kHz optional) Mode of Emission 16KOF3E (direct frequency modulation) Antenna Requirement 5042, unbalanced (SO-239 socket) Voltage Requirement 10.8 to 15.6 V DC, negative ground Current Consumption (approx.) 300 mA Stby, 700 mA Rx, 7.0 A Tx (FTL-1011: 9A) Operating Temperature Range -30 to +60 O C (-22 to +I40 OF) Size (WHD, approx.) 160 x 50 x 180 mm (6-1/4 x 2 x 7-h) Weight (approx.) 1.5 kg (3.3 lbs.) Receiver Receiver Circuit Type Intermediate Frequencies Sensitivity Hum & Noise Ratio Adjacent Channel Selectivity Intermodulation Distortion Spurious Rejection Audio Output Power Double Conversion Superheterodyne 16.9 MHz (FTL-101 I), 21.4 MHz (FTL-2011) or 47.9 MHz (FTL-701 l), and 455 kHz (all models) 0.2510.3 pV for 12 dB SINAD, 0.3510.45 pV for 20 dB QN (VHFIUHF, resp.) Better than 45 dB 80/75 or 70 dB (FTL-loll/-2011 and -701 1, resp.) Better than 70 dB (3-signal) Better than 80 dB (VHF), or 70 dB (FTL-7011) 5 watts into 4 ohms with <lo% THD Transmitter Power Output FTL-1011: 60 watts (fixed) FTL-2011: 4015 watts (highllow, programmable) FTL-7011: 2512 watts (highllow, programmable) Modulation TypeBeviation Frequency Modulation, f 5 kHz (+ 2.5 kHz optl) Hum & Noise Ratio Better than 45 dB Modulation Distortion Less than 5% Spurious Emissions Better than 70 dB (below carrier) Microphone Impedance 600 SZ Specifications subject to change without notice or obligation. page 13 Supplied Accessories MH-5j8 Microphone (optional in North America) Fused DC Cable: T9017910A w/two 10-A fuses (15-A in FTL-1011) MMB-48 Mobile Mounting Bracket Optional Accessories FDS-1 Digitally Coded Squelch Unit F2D-4 Sequential 2-Tone Decoder FRB-2 Programming Interface Box CE-5 Programming Software (for IBM PC/compatibles only) VPL-1 Programming Software (for IBM PC/compatibles only) T9 10141 0 Programming Connection Cable T9101411 Radio-to-Radio Cloning Connection Cable FP-711 AC (Base Station) Power Supply page 14 YAE SU Perfdrmance without compromise E02561101(405m-ZT) Printed in Japan.