Anritsu 11410-00235 电路图.pdf
The Industry Leader for High Frequency Components Precision RF Made in U.S.A. 11410-00235, Rev: D Data subject to change without notice Precision RF misalignment of the male pin with respect to the female contacts. To solve the problems the K Connector male pin is deliberately made shorter than the SMA or 3.5 mm pin. With this arrangement, the outer housing is properly aligned prior to the mating of the center conductors. Thus a proper, non-destructive alignment before mating is ensured. The effect of pin gap on a connection is often overlooked, but is the dominant source of error in many connection systems. Pin gap is the short length of smaller diameter caused when a connector pair is mated. Pin gap causes a discontinuity at the connector interface. The K Connector has considerably less susceptibility to pin gap than either SMA or 3.5 mm connectors. Many connector manufacturers specify connector performance assuming no pin gap, an unrealistic assumption. K Connectors are specified assuming pin gap to be at its maximum tolerance, to provide you the assurance of real-world specifications. Compatibility The K Connector interfaces electrically and mechanically with 3.5 mm connectors, including SMA and 3.5 mm without degradation in performance. Launcher design At the heart of the K Connector product line are the launchers. As their name implies, the launchers “launch” (make the transition) from a microwave circuit (microstrip, suspended substrate, stripline, or coplanar waveguide) to a coaxial connector and an outside transmission line. The key to making the transition without compromising electrical and mechanical objectives is the glass bead in the launcher assembly. SMA 3.5 0 -10 -20 -30 -40 Pin Gap Return Loss (dB) Frequency (GHz) 203040 K Pin Gap Male Center Pin Female Center Pin SMA/APC-3.5 K Connector Shortened Male Pin Eliminates Damage to Female K Connector Effect of Pin Gap For further information about these products and more,contact us at 1-800-ANRITSU or visit 5 K CONNECTOR DC to 40 GHz Low-reflection bead The K Connectors standard glass bead has a 0.30 mm center conductor and readily connects to fragile devices. The bead is appropriate for most applications employing Duroidand ceramic (Alumina) microstrip, such as the 0.25 mm wide transmission line on a 0.25 mm thick Alumina substrate. Applications using suspended substrate geometry are equally well satisfied. The bead is constructed of Corning 7070 glass and has a gold-plated center conductor and a gold-plated Kovarcollar. The outstanding design of the bead is largely accountable for the excellent performance of the K Connector launchers. Because the small 0.30 mm pin introduces minimal discontinuity, return loss is typically better than 20 dB at 40 GHz and better than 25 dB below 18 GHz. In addition, the design provides for soldering the bead to achieve a hermetic seal. 310C max. soldering temperature is recommended. Both the sparkplug (screw-in) and the flange-mount K Connector launchers offer an additional advantage over existing designs. These launchers do not use an epoxy pin to secure the center conductor, as used in some SMA designs. Without an epoxy pin, the outer conductor remains solid, and thereby eliminates the leakage path common to pin-captivated designs. Furthermore, K launchers have a wall thickness that is four times that of typical launchers (0.8 vs. 0.2 mm). The heavier wall results in superior resistance to over- torquing. Finally, the K Connector launcher can be removed for repair without removal of the glass bead. This ensures that during removal the critical microcircuit-to-glass bead interface is not disturbed, hermeticity is preserved, and the micro-circuit will not be subjected to the additional stress caused by heating to soldering temperature. Hardware locking compound such as “Removable Loctite” should be used to further secure the screw-in launcher in its housing. Complete family Virtually every interface need can be satisfied by one or more of the K Connector items offered. There are six different models of K Connector launchers. Two sparkplug (screw-in) launchers are available, the K102F female version and the K102M male version. Both screw into the housing that encloses the microwave circuit, and, like all Anritsu launchers, they can be easily removed for replacement or repair without unsoldering the glass bead and its interface to the microwave circuit. When the housing that encloses the microwave circuit is not thick enough to support a threaded, screw-in launcher, flush-mounted (flange) launchers are required. Models with two mounting holes are available in both male and female versions, K103M and K103F. Two other models, the K104F and K104M, have four mounting holes. Mounting hole spacing is identical to that of similar SMA flange launchers. The glass bead interface, of course, is the same design used for the sparkplug launcher. Cable connectors Both male and female cable connectors are available. The cable connectors, K101M and K101F, use gold-plated, beryllium- copper center conductors for optimum performance and wear characteristics, Typical return loss at 40 GHz for finished cables exceeds 16 dB (1.35 SWR). 5.3 1/4 X 36 UNS-2A THD 0.00 0.13 0.00 0.10 4.60 4.65 4.65 .22 10.4 1.93 1.27 .97 R .203 R .41 BLEND 1.07 1.60 1.27 7.7 7.9 HEX7.9 FLATS 7.1 1/4-36 UNS-2A 0.13 0.28 4.55 2.92 .91 2.9 0.00 0.10 0.00 0.10 16.2 4.44 4.65 Dimensions in millimeters K Connectorinterface dimensions in metric measurements Frequency (GHz) Return Loss (dB) 25 30 35 40 45 0481216242028323640 WSMA + K 3.5 mm + KSMA + K Return Loss Characteristics Solder Solder or Bond Solder 0.30 mm 1.42 mm 1.98 mm 0.03 Bead Microstrip, Coplanar Waveguide, Suspended Substrate +0.08 0.00 Transition from Microcircuit to External Transmission Line For further information about these products and more,contact us at 1-800-ANRITSU or visit 6 K CONNECTOR DC to 40 GHz Evaluation kit 01-101A Evaluation Kit Kit contains one K120 25 cm Male/Male Cable Assembly, two K102F Female Sparkplug Launcher Connector Assemblies, two K104F Female Flange Launcher Connector Assemblies, five K100 Glass Beads, one 01-102A Test Fixture, one 01-104 Drill and Tap Set, five K110-1 Microstrip Sliding Contacts, and all other parts and fixtures required to assemble launchers with or without sliding contacts. 01-104 Drill and Tap Set for precision machining of concentric holes for mounting K Connectorin microwave housing. (Drill Part No. B14094) (Tap Part No. 783-255) 01-105A Male and Female Sparkplug Torquing Kit 01-106 K Soldering Fixture for flange launcher glass bead, package of 5. 01-107M or 01-107F Cable Sleeve Soldering Fixture for K101M Male and K101F Female Cable Connectors, package of 10. 01-108 Drill and Tap Set For precision machining of concentric holes for mounting K Connectorin microwave housing in applications where stress relief contacts are used. (Drill Part No. B16526) (Tap Part No. 783-255) 3.00 0.81 Dimensions in millimeters K118 Semi-rigid Coaxial Cable 1.5m length of 3.00 mm semi-rigid cable for K101 series connector Semi-rigid coaxial cable Tools and fixtures 01-103 Soldering Fixture for sparkplug launcher glass beads, package of 10 Type Semi-rigid coaxial, tin-plated copper outer conductor, silver-plated copper center conductor. Impedance 50 2 Dielectric typeMicroporous Teflon, 0.24 cm diameter Dielectric constant1.687 Relative velocity0.77 Outside diameter3.00 mm Center conductor diameter0.81 mm Minimum bend radius0.65 cm Attenuation 1.6 dB/m at 10 GHz 2.3 dB/m at 20 GHz 3.3 dB/m at 30 GHz 4.7 dB/m at 40 GHz Anritsu provides two connector tools that make connecting and disconnecting tiny connectors more easily and surely accomplished. These tools are featured below. Features 01-201 Torque wrench: 0.9 N-M (8 in-lb) for standard SMA and 3.5 mm connectors, and for the Anritsu K Connectorand V Connector. 01-204 Handy stainless steel connector wrench for standard SMA, 3.5 mm, and 2.4 mm connectors, and for the Anristu K Connector and V Connector. 01-201 01-204 01-118 K ConnectorCable Assembling Fixture Kit for K118 semi-rigid coaxial cable. For further information about these products and more,contact us at 1-800-ANRITSU or visit 7 K CONNECTOR DC to 40 GHz 7.9 HEX 11.0 8.4 4.06 for K101M 3.05 for K101M-085 3.02 for K101M 2.26 for K101M-085 Dimensions in millimeters K101M K Male In-Line Cable Connector, DC-40 GHz for 3 mm cable K101M-085 for 2.16 mm cable 12.9 5.3 .5 4.65 3.04 1/4-36 UNS-2A 7.9 HEX Dimensions in millimeters K101F K Female In-Line Cable Connector, DC-40 GHz for 3 mm cable 16.2 8.4 .13 .28 4.65 1/4-36 UNS-2A 7.1 FLATS 7.9 HEX Dimensions in millimeters K102M K Male Sparkplug Launcher Connector, DC-40 GHz 10.4 5.33 .15 .30 4.65 5.33 1/4-36 UNS-2A Dimensions in millimeters K102F K Female Sparkplug Launcher Connector, DC-40 GHz 9.6 5.1 .05 .20 5.3 4.1 1.7 1/4-36 UNS-2A 5.7 2.8 15.9 12.2 2X 2.6 THRU Dimensions in millimeters K103F K Female Flange Launcher, two-hole, DC-40 GHz Launchers and cable connectors 13.1 8.4 7.9 HEX .05 .20 4.14 1.7 6.60 1.8 12.215.9 2X 2.6 Dimensions in millimeters K103M K Male Flange Launcher, two-hole, DC-40 GHz Coupling nut tightening torque1.36 N-m max Material Passivated stainless steel with heat-treated beryllium copper center conductors Pin depth 0.000 to -0.13 mm for male and female connectors Temperature range -55C to +125C (200C available; contact factory) Use with 01-104 or 01-108 Drill and Tap Sets Use with 01-103 or 01-106 Soldering Fixtures Use with 01-105A Male and Female Sparkplug Torquing Kit Use with 01-107M Cable Sleeve Fixture Use with 01-107F Cable Sleeve Fixture Use with 01-118 Cable Assembly Fixture Kit 9.6 5.1 .05 .20 5.3 1/4-36 UNS-2A 1.7 4.1 8.6 4X 2.6 THRU 8.6 15.9 12.7 SQ. Dimensions in millimeters K104F K Female Flange Launcher, four-hole, DC-40 GHz 14.7 8.4 .05 .20 7.92 HEX 1.7 4.1 8.6 4X 2.6 THRU 8.6 12.7 15.9 Dimensions in millimeters K104M K Male Flange Launcher, four-hole, DC-40 GHz For further information about these products and more,contact us at 1-800-ANRITSU or visit 8 K CONNECTOR DC to 40 GHz Ordering information Please specify model/order number, name, and quantity when ordering. Model/Order No.Name 01-101AK Connector(evaluation kit) 01-103Soldering fixture for sparkplug launcher glass bead 01-104Drill and tap set 01-105AMale and female sparkplug torquing kit 01-106Soldering fixture for flange launcher glass bead 01-107FCable sleeve soldering fixture, female connector 01-107MCable sleeve soldering fixture, male connector 01-108Drill and tap set 01-118Cable assembling fixture for K118 semi-rigid coax cable 01-201Torque wrench, for SMA, 3.5mm, and K Connector and V Connector 01-204Anritsu stainless steel connector wrench K110-1Microstrip stress relief contact K110-2Stripline stress relief contact K110-3Microstrip stress relief contact K101MK(m) in-line cable connector, DC to 40 GHz for K118 cable K101M-085K(m) in-line cable connector, DC to 40 GHz for V085 cable K101FK(f) in-line cable connector, DC to 40 GHz K102MK(m) sparkplug launcher connector, DC to 40 GHz K102FK(f) sparkplug launcher connector, DC to 40 GHz K103M K(m) flange launcher connector, DC to 40 GHz, 2 mounting holes K103FK(f) flange launcher connector, DC to 40 GHz, 2 mounting holes K104M K(m) flange launcher connector, DC to 40 GHz, 4 mounting holes K104FK(f) flange launcher connector, DC to 40 GHz, 4 mounting holes K118 Coaxial cable, 1.5m of 3.00 mm semi-rigid cable for K101 series connector S110-1 Microstrip and coplaner waveguide stress relief contact for 0.38 mm glass feedthru center conductor S110-3 Microstrip and coplaner waveguide stress relief contact for 0.38 mm glass feedthru center conductor Stress relief contacts Stress Relief Contacts provide an elegant yet simple solution to relieving stress at the interface of the microcircuit and its connecting coaxial conductor. These contacts simply slide onto the standard K100 and K100B glass bead pins. .711 .305 .152 .038 Dimensions in millimeters .711 .305 .038 .410 Dimensions in millimeters .711 .203.305 .406 .038 Dimensions in millimete K110-1Microstrip and Coplaner Waveguide K110-3Microstrip K110-2Stripline Frequency rangeDC to 40 GHz Material0.025 mm heat-treated BeCu PlatingBondable gold over nickel Use with 01-108 Drill and Tap Set 3.18 0.74 1.40 1.93 0.305 DIA. Dimensions in millimeters 3.18 0.74 1.40 1.93 0.305 DIA. Dimensions in millimeters K100 Glass Beads for K102, K103, and K104 connectors Note: Glass Beads can be purchased through recommended vendors. For more information visit . K100B High Hermeticity* Glass Beads for K102, K103, and K104 connectors Note: Glass Beads can be purchased through recommended vendors. For more information visit . *Glass Bead Hermeticity Spec:Hermetic to 1 x 10-8std cc He/sec at 1 atm differential .038 Dimensions in millimeters .229 .152 .711 S110-1 Microstrip and Coplaner Waveguide for 0.38 mm glass feedthru center conductor .038 Dimensions in millimeters .711 .203.305 .406 S110-3 Microstrip and Coplaner Waveguide for 0.38 mm glass feedthru center conductor For further information about these products and more,contact us at 1-800-Anritsu or visit 9 V CONNECTOR DC to 65 GHz The V Connectoris a reliable 1.85 mm device that operates up to 65 GHz. It is compatible with 2.4 mm connectors and is assembled using procedures that are similar to those used on K Connectors. It is well suited to applications in components, systems, or instrumentation. V Connectorfeatures Excellent performance up to 65 GHz Low VSWR Superior reliability Low Loss Exceptional reliability and repeatability Microwave connector reliability is affected by insertion force, outer conductor strength, stress relief while mating, and mating alignment. The V Connector exhibits exceptional performance in all of these areas. For proper seating, the V Connector requires only 1/2 the insertion force of a 2.4 mm connector. The reduced wear on the center conductor equates to greater reliability. All V Connectors, including the cable connectors, incorporate another feature that eliminates a major cause of connector failure; misalignment of the male pin with respect to the female. To solve the problem, the V Connector male pin is deliberately made sufficiently short to prevent damage to the female connector by misalignment. With this arrangement, the outer housing must be properly aligned prior to the mating of the center conductors. Thus a proper, non-destructive alignment before mating is ensured. The effect of pin gap on a connection is often overlooked, but is the dominant source of error in many connection systems. Pin gap is the short length of smaller diameter created when a connector pair is mated. Pin gap causes a discontinuity at the connector interface. TheV Connector has considerably less susceptibility to pin gap than 2.4 mm connectors. Many connector manufacturers specify connector performance assuming no pin gap, an unrealistic assumption. V Conn
