Biddle BITE2_2P_UG 电路图.pdf

AVTM246004 December 2003 Rev. C Instruction Manual BITE 2 and BITE 2P Battery Impedance Test Equipment (Includes AVOLink Addendum) BITE 2: Catalog No. 246002B BITE 2P: Catalog No. 246004 HIGH-VOLTAGE EQUIPMENT Read this entire manual before operating. APARATO DE ALTO VOLTAJE Ante de operar este producto lea este manual enteramente. M 2621 Van Buren Ave Norristown, PA 19403- 2329 610- 676- 8500 RadioFans.CN 收音机爱 好者资料库 RadioFans.CN 收音机爱 好者资料库 BITE 2 and BITE 2P Battery Impedance Test Equipment Instruction Manual RadioFans.CN 收音机爱 好者资料库 Copyright 2003 by Megger. All rights reserved. The information presented in this manual is believed to be adequate for the intended use of the product. If the product or its individual instruments are used for purposes other than those specified herein, confirmation of their validity and suitability must be obtained from Megger. Refer to the warranty information below. Specifications are subject to change without notice. WARRANTY Products supplied by Megger are warranted against defects in material and workmanship for a period of one year following shipment. Our liability is specifically limited to replacing or repairing, at our option, defective equipment. Equipment returned to the factory for repair must be shipped prepaid and insured. Contact your MEGGER representative for instructions and a return authorization (RA) number. Please indicate all pertinent information, including problem symptoms. Also specify the serial number and the catalog number of the unit. This warranty does not include batteries, lamps or other expendable items, where the original manufacturers warranty shall apply. We make no other warranty. The warranty is void in the event of abuse (failure to follow recommended operating procedures) or failure by the customer to perform specific maintenance as indicated in this manual. M 2621 Van Buren Ave Norristown, PA 19403-2329 610-676-8500 (Telephone) 610-676-8610 (Fax) email: M AVTM246004 BITE 2/2P Rev C Dec 2003 i Contents INTRODUCTION.1 About the BITE 2 and BITE 2P .1 How the BITE 2/2P Works.2 Applications for the BITE 2/2P.3 BITE 2/2P Measurements.4 Upon Receipt of the BITE 2/2P.4 Safety First.6 How to Use This Manual.7 Typographic Conventions.7 SAFETY.9 Overview.9 Safety Requirements.9 Connection to Power Source.11 Fuse Replacement.11 Cautions and Warnings.11 CONTROLS, CONNECTORS, INDICATORS AND MENUS.13 Overview.13 BITE 2 Transmitter.14 BITE 2P Transmitter.16 Receiver.18 Receiver Keys.19 Receiver Reset Switch .24 STANDARD TEST PROCEDURE.25 Overview.25 Step One: Prepare for Testing.27 Step Two: Powering-on the Receiver.28 Step Three: Scanning Test Information with the Wand (Optional).30 If You Do Not Want to Scan Information Using the Wand.30 If You Want to Scan Information Using the Wand.30 Step Four: Setting Baseline, Warning and Fail Values.32 Step Five: Splitting the Strap (if needed).33 If You Do Not Want to Split the Strap .33 If You Want to Split the Strap.33 Step Six: Connecting the Receiver and the BITE 2 or BITE 2P Transmitter to the Battery.35 Connecting the BITE 2 or BITE 2P Transmitter.37 Step Seven: Measuring the Cell and the Strap.38 Measuring the Next Section of a Sectioned Battery String.42 Step Eight: What to Do When the Test Is Complete.43 Reviewing a Test.43 Retesting Cells and Straps.44 Printing an Active Test to Review the Data (BITE 2P).44 Powering Down and Disconnecting the BITE 2/2P.45 M AVTM246004 BITE 2/2P Rev C Dec 2003 ii MODIFIED PROCEDURES FOR SPECIAL CONDITIONS.47 Overview.47 Reversing the Current Source Leads.47 Verifying the Source Current.48 Sectioning a Battery System.49 TRANSFERRING, PRINTING, AND DELETING TEST RESULTS.55 Overview.55 Exporting Test Results from the Receiver to a PC.56 Printing Test Results in the BITE 2P Transmitter Printer.58 Deleting Test Results from the Receiver.59 INTERPRETING TEST RESULTS.61 Overview.61 Instantaneous Interpretation.62 Short-Term Interpretation .63 Long-Term Interpretation.63 Temperature Corrections.64 SETTING OPTIONS.67 Overview.67 Turning the Receiver Backlight ON and OFF.68 Adjusting the Receiver Screen Contrast.68 Selecting the Receiver Language.69 Setting the Receiver Clock.69 Selecting the Line Frequency.71 MAINTENANCE AND TROUBLESHOOTING.73 Overview.73 Cleaning and Inspecting the BITE 2 and BITE 2P.74 Charging the Receiver.74 Replacing Batteries in the Receiver.75 Maintaining the Receiver Charger in the BITE 2 and BITE 2P.78 Maintaining Fuses in the BITE 2 and BITE 2P Transmitters.78 Verifying a Transmitter Fuse Problem.79 Replacing Fuses in the BITE 2 Transmitter .82 Replacing Fuses in the BITE 2P Transmitter.85 Interpreting Error Messages.88 If the BITE 2 or BITE 2P Needs Repairs.88 OPTIONAL EQUIPMENT.89 Available Options.89 APPENDIX A: TECHNICAL SPECIFICATIONS.91 Application.91 Electrical.91 BITE 2 and BITE 2P Transmitters.91 Receiver .92 Fuses.93 Mechanical.93 Environmental.94 Accessories - Standard .95 CONTENTS AVTM246004 BITE 2/2P Rev C Dec 2003 iii APPENDIX B: REPLACEABLE PARTS.97 Catalog Numbers 246002B and 246004.97 Catalog Numbers 246002B and 246004.98 How to Order Replaceable Parts for the BITE 2/2P .98 GLOSSARY.99 INDEX.