G-DEC_Jr._Service_Manual 电路图.pdf
G-DEC Jr (This is the model name for warranty claims) Fender Musical Instruments Corporation, 8860 East Chaparral Road Suite 100 Scottsdale, AZ 85250 Issued: February, 2007 p/n 2351000000 (120V) SERVICE MANUAL ATTENTION: WARRANTY SERVICE PROCEDURES Domestic (U.S. LOOP Start/Stop switch; and headphone present status are read via the analog multiplexer U6-A. The output of the multiplexer is read serially by the right channel of the CODEC and sent to the uDSP system Note: Troubleshooting the uDSP system to com- ponent level beyond verification of power supplies, clock, and data signals is NOT recom- mended. G-DEC Jr (This is the model name for warranty claims) 7 MIDI System MIDI Input signals from the external MIDI INPUT Jack (J4) are optically isolated via U22 and sent to the Rx line of the uDSP UART controller within U10 for processing. When MIDI is selected on the LOOP Selector, the MIDI signal being received is passed through to the Tx line of the uDSP UART and to the MIDI IN of the SAM2195 Dream Synthesizer chip U20. The SAMP2195 then plays MIDI sounds based on the commands being sent from the external MIDI sequence source. With internal LOOPS selected the external MIDI in- put is ignored and MIDI IN signals are generated by the uDSP system under control of the LOOP SE- LECT and KEY SELECT controls. The rate is controlled by the TEMPO control. Audio output from the SAM2195 Dream Synthesizer chip is mixed in at summing op-amp U2-B via R50/R54. The audio output of U2-B is mixed in with the instrument post processed (effects and amp types added) and Auxiliary Input audio at U2-A. POWER SUPPLIES The power transformer secondary windings are con- nected to the main PCB at P5 through P10. The +/-20VDC power supplies for the solid-state power amplifier are derived from the red-yellow-red secondary of the power transformer via full bridge rectifiers D4/D5 and D2/D3, and main filter caps C14 and C8. The yellow center tap lead and the systems chassis connection are placed between these caps, making this the system ground star. The +/-12VDC power supplies for the op-amps are regulated down from the +/-20 VDC supplies through dropping resistors R13-14 and Zener Diodes D6 and D7. The +11.5VDC power supplies for the Digital circuitry is derived from the brown-brown secondary of the power transformer via full bridge rectifiers D15, D16, D17 and D21 and filter caps C34. This raw supply is then regulated down to +5VDC by U5 (7805). The +5VDC supply powers multiplexer U6, Front Panel LED drivers Q5-Q7 and the D.C. reference voltage string R41-R43 for the high-low reference level for front panel potentiometers. The +5V is regu- lated down to 3.3v and 1.25V via U18 and U17 respectively. The 3.3V and 1.25 V supply power to the uDSP system components and the MIDI I/F components including the SAM2195 Dream Chip U20 and U22 MIDI input opto-isolator. Reset control- ler U12 monitors the +5V supply and shuts down all ICs in the event of power loss. USER INTERFACE The 4 - 16 position encoders (S2 S5) for the LOOP, AMP, KEY and EFFECT SELECT are read via the port expander U9 and the data sent to the uDSP sys- tem via the I2C interface lines SCL and SDA. The 4 potentiometers VOLUME(R51), GAIN(R49), TONE(R44), and TEMPO(R31) generate DC volt- ages (+1.0V to +4.0V) that are read by the analog multiplexer U6. IO0-IO3 are the digital control lines used to multiplex these analog signals which are sent serially to the system CODEC U13 on the Rin channel. The LOOP START/STOP button and the state of the HEADPHONE present signal are read in a similar manner. The uDSP system reads the state of these controls and inputs digitally from the CO- DEC. The LOOP VOLUME is a conventional analog con- trol which accepts the MIDI left and right loop audio signals from the SAM2195 MIDI Synthesizer via the mixer op-amp U7-B. G-DEC Jr (This is the model name for warranty claims) * Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above. shaded Unique Fender part. Order directly from the FMIC Parts Department. shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department. * Safety Requirement part. Replacement must match Safety AgencyValue, if specified Type, if specified Approval Mark(s) if on part. shaded + * Both a unique Fender part and a Safety Requirement part as defined above. 8 .PARTS LIST: MAIN PCB ASSEMBLY QTY. PART # DESCRIPTION REFERENCE DESIGNATION 1 REF *PCB ASSY G-DEC Jr MAIN COMPLETE PCB ASSY FIELD SERVICE ON THIS ASSY. LIMITED TO THE PART NUMBERS LISTED BELOW 5 REF WASHER TOOTHED AW-3 PCB MOUNTING 2 0072781000 JACK DIN PIN J4 MIDI IN 5 REF CONTROL 10kB R3,R31,R38,R44,R49,R51 4 0055983000 ENCODER 16PS 4BITGRY RTRY S2-S5 1 0041812000 IC REGULATOR +5V MC7805CT U5 1 0051934000 IC POWER AMP TDA2050V 32W U3 1 REF *HEAT SINK G-DEC Jr U3, U5 2 REF SCREW M3X10 BLK B/H U3, U5 2 REF WASHER FLAT M3 U3, U5 2 REF NUT M3 NIP U3, U5 2 REF WASHER SPLIT LOCK M3 U3, U5 2 REF BUSHING PATR-2935 U3, U5 2 REF SILICONE PAD TO-220 U3, U5 4 0051658000 JACK MONO 1/4 J3 INPUT 2 0072780000 JACK 3.5 mm STEREO W/SWITCH J1, J2 AUX INPUT, HEADPHONE OUTPUT PARTS LIST: CHASSIS ASSEMBLY QTY. PART # DESCRIPTION REFERENCE DESIGNATION 1 REF CHASSIS G-DEC Jr 1 REF *PCB ASSY G-DEC Jr MAIN COMPLETE PCB ASSY 1 REF *XFMR G-DEC Jr 120V - REF *XFMR G-DEC Jr 230V - REF *XFMR G-DEC Jr 100V 1 0039287000 POWER SWITCH SNAP IN 1 REF TRANSFORMER GASKET TRANSFORMER BASE 4 006470600 KNOB ROTARY G-DEC Jr POTS (with flat washer and nut) 5 REF KNOB ENCODER G-DEC Jr FX, KEY, AMP, LOOP (with flat washer and nut) 1 0048451000 PUSH BUTTON IVORY LOOP START/STOP 8 REF WASHER DIA 9 CRP 2EA INSIDE OF ENCODER SHAFTS 1 0072791000 *IEC INLET AC INLET - 0048381000 *FUSE T600mA 5X20MM 100V UNITS ONLY Littelfuse 218P.600 1 0003111000 *FUSE T500mA 5X20MM 120V UNITS ONLY Littelfuse 218P.500 - REF *FUSE T250mA 5X20MM 230-240V UNITS ONLY Littelfuse 218P.250 5 REF M3X5 ZNP B/H PCB 5 REF AW-3 PCB 3 REF FLANGE NUT M) 4 ZNP XFMR, GND 2 REF TF 6-32X6 BLK B/H REAR I/O PCB 2 REF T 2.1X8 BLK R/H MIDI JACK 3 REF TF 4-40X6 ZNP B/H HEAT SINK G-DEC Jr (This is the model name for warranty claims) * Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above. shaded Unique Fender part. Order directly from the FMIC Parts Department. shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department. * Safety Requirement part. Replacement must match Safety AgencyValue, if specified Type, if specified Approval Mark(s) if on part. shaded + * Both a unique Fender part and a Safety Requirement part as defined above. 9 PARTS LIST: END ITEM ASSEMBLY QTY. PART # DESCRIPTION REFERENCE DESIGNATION 1 REF *CABINET ASSY G-DEC Jr 5 REF SCREW M) 4X30 BLK T/H CABINET BACK 1 REF SPEAKER 8 8 OHM G-DEC Jr 4 REF NUT FLANGE M) 4 ZNP SPEAKER 1 0047248000 *CORD PWR W/IEC CONN DOM 120V ONLY - 0047249000 *CORD PWR W/IEC CONN 230V UK 230V UK ONLY - 0047250000 *CORD PWR W/IEC CONN 240V 240V AUS ONLY - 0047251000 *CORD PWR W/IEC CONN 230V 230V EUR ONLY 0057674000 *CORD PWR W/IEC CONN 230V ARG 230V ARG ONLY - 0053997000 *CORD PWR W/IEC CONN 100V JPN 100V JPN ONLY 1 0072802000 *BADGE G-DEC 2 REF SCREW T) 2.1X10 NIP R/H BADGE 1 0051043000 *NAMEPLATE FENDER GENERIC 4 0036500000 ESCUTCEHON PINS NAMEPLATE 1 REF MANUAL OWNERS G-DEC Jr 5 REF SCREW NO. 8 U32X30 BLK O/H CHASSIS TOP AND REAR 3 REF SCREW M 3.5X10 BLK T/H CHASSIS REAR 4 REF WASHER BLK FINISHING TYPE CHASSIS 1 0037121000 HANDLE RIBBED 9 1/4 2 0032524000 HANDLE STRAP METAL INSERT 2 0025395000 HANDLE CAPS - NICKEL 2 REF M)4X32 NIP O/H HANDLE 4 REF FOOT RUBBER 18X10 4 REF T)2.1X8 BLK R/H FEET G-DEC Jr (This is the model name for warranty claims) 10 Service Diagram List Service Diagram (Schematic) .G-DEC Jr PCB
