bossBF-3A_SERVICE_NOTES电路图.pdf

SERVICE NOTES Issued by RJA Copyright 2011 Roland Corporation All rights reserved. No part of this publication may be reproduced in any form without the written permission of Roland Corporation. CC-KWS17058043E1 Jun. 2011BF-3(T) Table of Contents Identifying the BF-3(T).2 Cautionary Notes.2 Specifications .3 Location of Controls .4 Exploded View.5 Disassembly Procedure.6 Conversion to the BF-3A.6 Parts List.7 Verifying the Version.9 Data Backup and Restore Operations .9 Performing a Factory Reset.9 Updating the System .9 Test Mode.9 Circuit Board (Main, VR, LED, SW, Output B Board).12 Circuit Diagram (Main, VR, LED, SW, Output B Board).14 RadioFans.CN 收音机爱 好者资料库 2 Jun. 2011BF-3(T) Identifying the BF-3(T) The BF-3(T) exists in two types that have different circuit structures. In this Service Notes, the older type is called the BF-3, and the newer type is called the BF-3A. Both have Flanger BF-3 inscribed on the pedal and appear at a glance to be completely identical, but they can be distinguished as indicated in the following table. After identifying the type of the product being serviced, refer to the corresponding Service Notes for information on required parts and test methods. BF-3:SERVICE NOTES (#17058043E0) BF-3A:SERVICE NOTES 2ND EDITION (#17058043E1) This version of Service Notes is for the BF-3A. Cautionary Notes Before beginning the procedure, please read through this document. The matters described may differ according to the model. User Data Cannot Be Backed Up The setting for the sleep mode is saved on the Main Board even when the power has been switched off, but neither verification of its status (ON or OFF) nor backing up the setting is possible. When the Main Board has been replaced, the sleep mode is returned to its default (ON). For more information about the sleep mode, refer to About Sleep Mode (Owners Manual, p. 14). No user data other than the setting for the sleep mode is saved. Part Replacement When replacing components near the power-supply circuit or a heat- generating circuit (such as a circuit provided with a heat sink or including a cement resistor), carry out the procedure according to the instructions with respect to the part number, direction, and attachment position (mounting so as to leave an air gap between the component and the circuit board, etc.). Parts List A component whose part code is * will not be supplied as a service part because one of the following reasons applies. Because it is supplied as an assembled part (under a different part code). Because a number of circuit boards are grouped together and supplied as a single circuit board (under a different part code). Because supply is prohibited due to copyright restrictions. Because reissuance is restricted. Because the part is made to order (at current market price). Because it is carried in electronic data on the Roland web site. Because it is a package or an accessory irrelevant to the function maintenance of the main body. Because it can be replaced with an article on the market. (battery or etc.) Circuit Diagram In the circuit diagram, “NIU” is an abbreviation for “Not in Use,” and “UnPop” is an abbreviation for “Unpopulated.” They both mean non-mounted components. The circuit board and circuit board diagram show silk-screened indications, but no components are mounted. BF-3BF-3A Production numberUp through H*8559 H*8560 and after Style of component mounting on the circuit board Single-side mounting Double-side mounting System versionVersion 1.00Version 2.00 or later RadioFans.CN 收音机爱 好者资料库 3 Jun. 2011BF-3(T) Specifications BF-3: Flanger (BF-3A) Nominal Input Level -20 dBu Input Impedance 1 M Nominal Output Level -20 dBu Output Impedance 1 k Recommended Load Impedance 10 k or greater Delay Time 0.3 mS14.4 mS (GUITAR IN) 0.3 mS6.3 mS (BASS IN) LFO Speed 100 mS18 S Residual Noise -95 dBu (IHF-A Typ.) Controls Pedal Switch MANUAL Knob RES (resonance) Knob DEPTH Knob RATE Knob MODE Knob Indicator CHECK Indicator (Serves also as tempo and battery check indicator) Connectors GUITAR IN Jack BASS IN Jack OUTPUT A (MONO) Jack OUTPUT B Jack AC adaptor Jack (DC 9 V) Power Supply DC 9 V; Dry battery 6F22 (9 V) type (carbon)/Dry battery 6LR61 (9 V) type (alkaline) AC Adaptor (PSA-series: optional) Current Draw 40 mA (DC 9 V) *Expected battery life under continuous use: Carbon: 3 hours Alkaline: 10 hours These figures will vary depending on the actual conditions of use. Dimensions 73 (W) x 129 (D) x 59 (H) mm 2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches Weight 435 g /1 lb (including Battery) Accessories Owners Manual (#5100021063) Leaflet (“USING THE UNIT SAFELY,” “IMPORTANT NOTES,” and “Information”) (#*) Dry battery/9 V type (6F22) (#*) *The battery that was supplied with the unit is for temporary use intended primarily for testing its operation. Options AC Adaptor PSA-series *0 dBu = 0.775 Vrms *Printed matters will not be supplied after the end of the production. Then, download the electronic file from the Roland web site. *In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice. RadioFans.CN 收音机爱 好者资料库 4 Jun. 2011BF-3(T) Location of Controls fig.panel.eps 16 17 18 No.Part CodePart NameDescriptionQty 15100014487COMPACT PSA LABEL(22537538R0)1 25100021036PANEL1 35100021031CASE1 422480220P R-KNOB (INTERNAL)(SS) BF BLK/LCG1 22480221P O-KNOB (EXTERNAL)(OUTER) S BLK/LCG1 5100018911ROTARY POT(F3229220R0)RD912DF-20-20FWH-B50K-60009A21 40128923HEX NUT M71 551000013416.5MM JACKHTJ-064-12DMP (13449150R1)1 5100003926PLAIN WASHER 9X13.5X0.5TNI(H5039158R0)1 5100008086INT TOOTH WASHER 9.5X12.5X0.5NI RTC(H5039205R0)1 5100003918JACK NUT M9X12X2NI RTC(H5039510R0)1 5100015893PLAIN WASHER 9.2X14X1.6NI (H5039104R0)1 5100015900PLAIN WASHER 9.6X14XW11X1.0AL (22137709R0)1 613449105R06.5MM JACKHTJ-064-14I1 5100003926PLAIN WASHER 9X13.5X0.5TNI(H5039158R0)1 5100008086INT TOOTH WASHER 9.5X12.5X0.5NI RTC(H5039205R0)1 5100003918JACK NUT M9X12X2NI RTC(H5039510R0)1 75100008294PEDAL PLATE(22357304R0)1 85100006632BOTTOM COVER(22027851R0)1 95100006633BOTTOM FOOT(22357305R0)1 105100006631CAUTION SEALPSA (FCC/EMI)(G2537516R2)1 115100007512THUMB SCREW(H5029820R0)1 12F3439875R0ADAPTOR JACKKM02018ABM1P1 13F5029423R0LEDL-3VEGW1 5100002339LED SPACER3041 1404567601P R-KNOBMF BLK/LCG(22480260R0)1 5100014193R.POTENTIOMETER (F3279853R0)RD901F-20-15FB-B50K-041 40128923HEX NUT M71 1504567601P R-KNOBMF BLK/LCG(22480260R0)2 F3279852R0POTENTIOMETERRD901-20-15FW-B54-0062 40128923HEX NUT M72 1651000206096.5MM JACKSCJ614M2NCS3B11G1 5100003926PLAIN WASHER 9X13.5X0.5TNI(H5039158R0)1 5100008086INT TOOTH WASHER 9.5X12.5X0.5NI RTC(H5039205R0)1 5100003918JACK NUT M9X12X2NI RTC(H5039510R0)1 1751000064576.5MM JACKHTJ-064-14D(13449140R0)1 5100003926PLAIN WASHER 9X13.5X0.5TNI(H5039158R0)1 5100008086INT TOOTH WASHER 9.5X12.5X0.5NI RTC(H5039205R0)1 5100003918JACK NUT M9X12X2NI RTC(H5039510R0)1 185100021035PEDAL1 5 Jun. 2011BF-3(T) Exploded View fig.bunkaizu.eps 1 2 3 4 5 6 7 8 9 10 a b c d No.Part CodePart NameDescriptionQty 113129710R0SWITCH(PUSH)JM-04041 25100007503BATTERY CUSHION(22267333R0)1 35100007872BATTERY CONNECTOR006P BATTERY SNAP (F3419102R0)1 45100006631CAUTION SEALPSA (FCC/EMI)(G2537516R2)1 55100006633BOTTOM FOOT(22357305R0)1 65100006632BOTTOM COVER(22027851R0)1 75100022073INSULATING SHEET1 85100007505PEDAL GUIDE BUSH(22157702R0)1 95100007504COIL SPRING(22177109R0)1 105100008294PEDAL PLATE(22357304R0)1 a5100008092PLAIN WASHER 3X6X0.5RESIN RTC(H5039708R0)2 b40010267SCREW M3X10BINDING MACHINE FE BZC2 c5100007965SCREW 3X6(H5029325R0)PAN TAPPING B1 BZC4 d5100007512THUMB SCREW(H5029820R0)1 6 Jun. 2011BF-3(T) Disassembly Procedure 1.Remove No. 6 Bottom Cover, and No. 7 Insulating Sheet. 2.Lift the Main Sheet Assy. 3.Remove the VR Board (1), and then the OUTPUT B jack (2). fig.bunkai.eps Conversion to the BF-3A When converting from the BF-3 (older type) to the BF-3A (new type), replace the components shown in the following chart. fig.insulating-sheet.eps 5100023214 INSULATING SHEET 36X14X0.5 BF-3BF-3A Part CodePart NameDescriptionPart CodePart NameDescription 75D6439001MAIN BOARD ASSY - 5100020562MAIN SHEET ASSY *MAIN BOARD *MAIN BOARD *VR BOARD *VR BOARD *LED BOARD *LED BOARD *SW BOARD *SW BOARD 75D643O000OUT JACK ASSY *OUTPUT B BOARD G2167301INSULATION SPACER-5100022073INSULATING SHEET(for insulating the bottom) *INSULATING SHEET-5100023214INSULATING SHEET36X14X0.5 (for insulating OUTPUT B) G6017304OWNERS MANUALJAPANESE-5100021062OWNERS MANUALJAPANESE G6017305OWNERS MANUALENGLISH-5100021063OWNERS MANUALENGLISH 1 2 7 Jun. 2011BF-3(T) Parts List fig.-part1-e.eps Safety Precautions: The parts marked have safety-related characteristics. Use only listed parts for replacement. Note: The parts marked # are new. (initial parts) The description “Qty” means a necessary number of the parts per one product. Due to one or more of the following reasons, parts with parts code * cannot be supplied as service parts. Part supplied only as a component in a complete assembly Copyright does not permit the part to be supplied Part is sold commercially CASING 5100021031CASE1 5100021036PANEL1 5100021035PEDAL1 5100006632BOTTOM COVER(22027851R0)1 CHASSIS 5100008294PEDAL PLATE(22357304R0)1 KNOB, BUTTON 04567601P R-KNOBMF BLK/LCG(22480260R0)3 22480220P R-KNOB (INTERNAL)(SS) BF BLK/LCG1 22480221P O-KNOB (EXTERNAL)(OUTER) S BLK/LCG1 SWITCH 13129710R0SWITCH(PUSH)JM-0404(13129710R0)SW500 (SW Board)1 JACK, EXT TERMINAL #51000206096.5MM JACKSCJ614M2NCS3B11GJK500 (Guitar In)1 51000064576.5MM JACKHTJ-064-14D(13449140R0)JK501 (Bass In)1 51000013416.5MM JACKHTJ-064-12DMP (13449150R1)JK502 (OUTPUT B)1 13449105R06.5MM JACKHTJ-064-14IJK503 (OUTPUT A)1 F3439875R0ADAPTOR JACKKM02018ABM1P1 PWB ASSY #5100020562MAIN SHEET ASSY1 *This unit includes the following parts. *MAIN BOARD1 *VR BOARD1 *LED BOARD1 *SW BOARD1 *OUTPUT B BOARD1 DIODE F5029423R0LEDL-3VEGWLED500 on LED Board1 POTENTIOMETER 5100018911ROTARY POT(F3229220R0)RD912DF-20-20FWH-B50K-60009A2VR500 (RES, MANUAL)1 5100014193R.POTENTIOMETER (F3279853R0)RD901F-20-15FB-B50K-04VR503 (MODE)1 F3279852R0POTENTIOMETERRD901-20-15FW-B54-006VR501, VR502 (DEPTH, RATE)2 WIRING, CABLE 5100021030WIRINGW2(3PIN)1 5100021029WIRINGW1(7PIN)1 SCREWS 40010267SCREW M3X10BINDING MACHINE FE BZC2 5100007965SCREW 3X6(H5029325R0)PAN TAPPING B1 BZC5 5100007512THUMB SCREW(H5029820R0)1 40128923HEX NUT M74 5100003918JACK NUT M9X12X2NI RTC(H5039510R0)4 5100008086INT TOOTH WASHER 9.5X12.5X0.5NI RTC(H5039205R0)4 5100008092PLAIN WASHER 3X6X0.5RESIN RTC(H5039708R0)2 5100003926PLAIN WASHER 9X13.5X0.5TNI(H5039158R0)4 5100015893PLAIN WASHER 9.2X14X1.6NI (H5039104R0)1 5100015900PLAIN WASHER 9.6X14XW11X1.0AL (22137709R0)1 8 Jun. 2011BF-3(T) MISCELLANEOUS 5100007872BATTERY CONNECTOR006P BATTERY SNAP (F3419102R01 5100007503BATTERY CUSHION(22267333R0)1 5100006633BOTTOM FOOT(22357305R0)1 5100006631CAUTION SEALPSA (FCC/EMI)(G2537516R2)1 5100007504COIL SPRING(22177109R0)1 5100014487COMPACT PSA LABEL(22537538R0)1 #5100020413EARTH TERMINAL2 #5100023214INSULATING SHEET36X14X0.51 5100022073INSULATING SHEET1 5100007870INSULOCK TIEYJ-80 V2 (H5319102R0)2 5100002339LED SPACER3041 5100007505PEDAL GUIDE BUSH(22157702R0)1 ACCESSORIES (Standard) #5100021062OWNERS MANUALJAPANESE1 #5100021063OWNERS MANUALENGLISH1 9 Jun. 2011BF-3(T) Verifying the Version 1.Turn down all controls completely counterclockwise (to MIN or MOMENTARY). 2.Hold down the pedal and connect the AC adaptor to the DC IN jack. The CHECK LED lights up and the unit enters the Test Mode. After approximately 2 seconds, the CHECK LED lights up or flashes, indicating the version as shown below. Examples:Illuminated orange:Version 1.00 2 flashes:Version 2.00 *Version 1.00 is the BF-3 (older type), and version 2.00 is the BF-3A (new type). After the version information is displayed, execution changes to 1. DSP and CPU Check. 3.Release the pedal. Data Backup and Restore Operations The setting for the sleep mode is saved on the Main Board even when the power has been switched off, but neither verification of its status (ON or OFF) nor backing up the setting is possible. When the Main Board has been replaced, the sleep mode is returned to its default (ON). For more information about the sleep mode, refer to About Sleep Mode (Owners Manual, p. 14). No user data other than the setting for the sleep mode is saved. Performing a Factory Reset This product has no factory-reset feature. Updating the System A system update cannot be performed for this product. If an update is required, replace with an updated circuit board. Updates can be accomplished only at the factory. Test Mode Items Required AC adaptor (PSA-series device) Amp-equipped monitor speaker x 1 Signal generator x 1 Oscilloscope x 1 Noise meter x 1 Stabilized power supply x 1 47-k dummy plug x 1 Test Items 1. DSP and CPU Check (p. 10) 2. Volume Check (p. 10) 3. CODEC (DAC) Check (p. 10) 4. CODEC (ADC) L-channel Check (p. 11) 5. CODEC (ADC) R-channel Check (p. 11) 6. Battery Operation Check (p. 11) 7. Noise Check (p. 11) *6. Battery Operation Check is carried out in the normal mode, and not in the Test Mode. 7. Noise Check is carried out in its own mode. Entering the Test Mode 1.Turn down all controls completely counterclockwise (to MIN or MOMENTARY). 2.Hold down the pedal and connect the AC adaptor to the DC IN jack. The CHECK LED lights up and the unit enters the Test Mode. 3.Release the pedal. *The unit cannot enter the Test Mode unless all controls are turned down to minimum. If the minimum value is not detected for all volume controls due to a problem such as a defective volume control, the Test Mode cannot be entered. Quitting the Test Mode Depress the pedal. *If an error occurred in 1. DSP and CPU Check, depressing the pedal does not quit the mode. In such cases, disconnect the AC adaptor to switch off the power. *At 5. CODEC (ADC) R-channel Check, depressing the pedal does not quit the mode. In th