Gallien-krueger_200MK,_200RK_Service_Manual电路图.pdf

? ? RadioFans.CN 收音机爱 好者资料库 ? ? ? ?!?# $?!?%$?&?( )? RadioFans.CN 收音机爱 好者资料库 RadioFans.CN 收音机爱 好者资料库 200MK / 200RK TURN-ON PROCEDURE 2/1/88 Rev. 9/28.99-SW 1)Inspect board. 2)Observe the following: variac at 0, no load, speaker load on, cabinet speaker off, tones on 10, master on 0, R5 clockwise, R291 Counter- clockwise, all switches out. 3)Gradually adjust variac to 20Vrms. U23/8= 3.2V +or - .5V, U23/4= 1.3V +or - .5V. Reg. Supplies 4V +or - .5V ,-2.6V +or - .5V. 4)Gradually adjust variac to 70Vrms. Watch variac (amps), scope and listen to speaker. Amp should not draw current. Output will go 4V, then 6V, then snap to 0 between 30-40Vrms. U23/8= 11.5V +or - .5V, U23/4= -11.5V +or - .5V. Reg. Supplies 14.5V +or - .5V ,-14.5V +or - .5V. 5)Continue to adjust to 120Vrms. Supplies + or- 45V + or - .5V. 6)Turn speaker load off. 7)Adjust bias. Adjust R224 to get a 5mV bias across R214, 225 (most positive of the two), and R240, 241 (most negative of the two). 8) Set the following: 400Hz sine wave 500mVrms at piano input, master 10, limit switch on. 9)Limiter adjust. Adjust R191A to get a flat response at U24/2. Compare to limiter response figure. Turn off. 10) Set the following: master 0, 4 ohm load. 11) Full power, limiter, and current limiter test. Gradually turn up master until clipping. Output = 20Vrms and clip evenly. Turn up master to 10. Output should hit the rails hard. Engage limiter. Output should swell down from heavy clipping then swell up to full power without clipping or bouncing. Change to 2 ohm load- output should be a clean sine wave without clipping and = 12Vrms. Change to no load and disengage limiter. 12) Set master to 5. 13) Output should = 35Vrms. Plug into Synth. 1, then 2. Output should remain the same for all 3 inputs. 14) Plug into Monitor In. Output should = 27Vrms. 15) Plug back into Piano Input and measure direct outs = 8Vp-p. 16) Check line out. Should be clean sine wave and = 750mVrms. 17) Check headphones. Should have slight clipping with 15Vp-p. 18) Compressor test. Engage compressor. Output will attenuate and = 19Vrms without clipping. Turn up input signal 10dB. Output = 33Vrms without clipping. Turn signal down 20dB. Output = 10Vrms without clipping. Disengage compressor. 19) Chorus adjust. Engage chorus. Amplitude will vary up and down at output. Check direct out in stereo mode. D.O.s should look different but at same frequency. In mono mode, D.Os should look same. Repeat (18)- (compressor test) for Synth. 1 and Synth. 2 inputs. 20) Echo adjust. Engage echo. Adjust R84 to get 400mVrms at U10/6. 21) Change the following: square wave input 400Hz 500mVp-p, tones at 5, master at 9 oclock position. 22) Check tone controls for each input and compare to figures. 23) Engage echo and compare to echo figure for each input channel. 24) Turn on speaker cabinet and do quick audio test with echo on, then chorus on for each input channel. 25) Noise and tap test. Tones 10, Master 10, switches in noise < 20mVrms. Tones 10, Master 0, switches out noise < 2.2mVrms Noise should be clean without popping or crackling. Sharply tap the amp on the bench a few times to make sure nothing fails. Ready For Burn-in 200MK INDENTED BILL OF MATERIALS NOTE:Level 1 refers to main assembly parts. Level 2 refers to board level components. Main assembly numbers are in bold face, while commonly needed parts are italicized. LVLPART#DESCRIPTIONQTYREF. DESIG. 1010-0012-0MPSA06 NPN 80V 500MA TO-921 1011-0023-0TIP29C NPN 100V 1A TO-220 FP1 1011-1035-0TIP30C PNP 100V 1A TO-2201 1012-0085-0TIP-35CFP NPN 100V 25A TO2182 1012-1086-0TIP 36CFP,PNP,100V,25A,TO-218,PECOR2 1025-0116-0RED LED,1.5MCD,120 DEG,T-11 1080-0488-0X-FORMER BACKLINE,DOMESTIC1 1082-0039-0SPEAKER,12,80W,Z=8,PYLE FOAM EDGE1 1082-0045-0SPEAKER,3,Z=16,PYLE TWEETER1 1091-0003-0FUSE, 3A,125V,1/4X1 1/4,SLB1 2799-TEST-0TRY OUT0 1092-0045-0XLR,MALE,X70101 LUGS2 1092-0064-0Q-CON, .25 TAB,18-22GA,INSULATED8 1093-0014-0RECEPTICAL AC,Q-TERM1 1093-0032-0HOUSING,3X.156,FEMALE 22GA,LOCK2 1094-0013-0HOLDER,FUSE,1/4 X 1 1/4,Q-TERM1 1094-0018-0SOLDER LUG,#41 1095-0005-0POWER CORD,117V PLUG,DETACH1 1100-0005-0WASHER,RUBBER,1/8ID X 3/8OD X 1/8T4 1100-0027-0BUTTON,ROUND BLACK CAP - PUSH SWITCH10 1100-0030-0BUTTON,RECT BLACK CAP - PUSH SWITCH1 1100-0031-0WASHER,#4,RECT,TO-220 MGT2 1100-0037-0HEAT CLIP,TO-981 1100-0038-0BUMPER,ROUND RUBBER,5/8X5/162 1100-0072-0GROMMET,.187 I.D.4 1100-0076-0FOOT,RUBBER,ROUND,5/8DIA. X 5/84 1100-0080-0HANDLE RUBBER,101 1100-0098-0KNOB,GRAY,6X15MM SPLINE SHAFT7 1100-0108-0X-FORMER BRACKET,FOR BACKLINE4 LVLPART#DESCRIPTIONQTYREF. DESIG. 1111-0061-0BOLT 4-40 3/8 PHP CAD4 1111-0081-0BOLT 4-40 1/2 PHP CAD9 1111-3041-0SCREW 4AB 1/4 PHP CAD4 1111-4080-0SCREW 4AB 1/2 FHP 82 B.O.8 1111-6001-0NUT 4-40 KEP SMALL3 1111-6011-0NUT 4-40 HEX SMALL CAD5 1111-7011-0WASHER #4 SPLIT4 1112-0051-0BOLT 6-32 5/16 PHP CAD4 1112-1050-0BOLT 6-32 5/16 FHP 82 B.O.4 1112-1100-0BOLT 6-32 5/8 FHP 82 B.O.4 1112-4080-0SCREW 6AB 1/2 FHP 82 B.O.4 1112-6001-0NUT 6-32 KEP LARG SIZE CAD1 1112-7001-0WASHER #6 FLAT CAD4 1112-9060-0TR-BOLT 6-32 3/8 FHP B.O.38 1113-0080-0BOLT 8-32 1/2 PHP B.O.4 1113-0080-0BOLT 8-32 1/2 PHP B.O.4 1113-0221-0BOLT 8-32 1 3/4 PHP CAD4 1113-6011-0NUT 8-32 KEP CAD4 1113-6011-0NUT 8-32 KEP CAD8 1114-0080-0BOLT 10-32 1/2 PHP B.O.2 1114-7011-0WASHER #10 FLAT CAD4 1115-7005-0WASHER 3/8 FIBRE FLAT3 1115-7021-0WASHER 3/8 INTERNAL CAD5 1130-0000-0OVERLAY,MICRO BASS GRILL-1121 1132-0349-A200MK/MV TOP COVER1 2120-0005-0ALUM .10098 1132-0350-B200MB-MK RIGHT SIDE1 2114-6046-0NUT 10-32 CAPTIVE1 2120-0005-0ALUM .100164 1132-0351-B200MB-MK LEFT SIDE1 2114-6046-0NUT 10-32 CAPTIVE1 2120-0005-0ALUM .100164 1132-0356-B200MK GRILL1 LVLPART#DESCRIPTIONQTYREF. DESIG. 2120-0003-0STEEL,16GA,PERF,3X10X.0600 2120-0011-0STEEL,18 GAUGE JET COAT,.048272 1132-0360-D0000 200MK BACK1 2120-0005-0ALUM .100406 1132-0361-B200MK BAFFLE1 2120-0005-0ALUM .100384 1132-0362-B200MK FRONT PANEL1 2112-6016-0NUT 6-32 CAPTIVE5 2120-0007-0ALUM .06354 1132-0363-B200MK REAR PANEL1 2112-6016-0NUT 6-32 CAPTIVE10 2120-0005-0ALUM .10042 1160-0006-0MANUAL,200MK1 1160-0006-0MANUAL,200MK1 1202-0016-0200MK WIRE KIT1 1206-0050-C200MK-RK AMP1 2001-0001-0MN3011 MULTI-TAP BBD1U24 2001-0006-0MN3007 1024 STAGE BBD2U25,28 2001-1030-0LF353N DUAL JFET OP AMP18U1,3,4,5,6,7,8,9,12,15,16,17,18,20,22,23,29,30 2001-1038-0LM386 LOW VOLTAGE POWER AMP2U13,14 2001-2009-0LM556CN DUAL TIMER1U27 2001-3028-0TL604 DUAL COMP ANALOG SWITCH2U11,19 2001-4043-0NE571 DUAL COMPANDOR3U2,10,21 2002-0034-0CD4013 DUAL D FLIP-FLOP1U26 2010-0012-0MPSA06 NPN 80V 500MA TO-925Q4,6,7,14 2010-1013-0MPSA56 PNP 80V 500MA TO-925Q3,5,13,16,18 2010-2010-0J113 N-JFET 35V 2MA TO-922Q1,2 2011-0023-0TIP29C NPN 100V 1A TO-220 FP1Q8 2011-1035-0TIP30C PNP 100V 1A TO-2202Q9,19 2020-0036-01N747A,ZENER,3.6V,5%,400MW,DO-354D5,6,16,17 2020-0120-01N759A,ZENER,12V,5%,400MW,DO-358D1,2,3,4,7,8,18,19 2020-0160-01N966B,ZENER,16V,5%,400MW,DO-352D29,30 2020-0200-01N968B,ZENER,20V,5%,400MW,DO-351D31 LVLPART#DESCRIPTIONQTYREF. DESIG. 2020-1103-01N914 ,RECT-FAST,200MA,100V,4NS,DO-3511D9,10,11,12,13,14,20,21,22,23,24 2020-2105-01N4002,RECT,1A,150V,DO-415D25,26,27,28,32 2023-0109-0KBPC-102 BRIDGE RECT 3A,200V,C219K1BR1 2030-0223-0CAP,CERAMIC AXIAL,223,30%,16V2C23,121 2030-1103-0CAP,CERAMIC AXIAL,103,30%,25V6C12,41,104,109,111,120 2030-2101-0CAP,CERAMIC AXIAL,101,5%,50V8C1,2,6,20,25,28,29,96 2030-2102-0CAP,CERAMIC AXIAL,102,10%,50V2C119,122 2030-2104-0CAP,CERAMIC AXIAL,104,10%,50V,XR7,.39C34,C51,C52,C56,C57,C72,C79,C94,105 2030-2222-0CAP,CERAMIC AXIAL,222,10%,50V21C13,22,26,32,46,47,50,62,63,64,65,68,69,73, 74,76,78,81,83,84,016,110 2030-2271-0CAP,CERAMIC AXIAL,271,10%,50V9C21,48,49,67,71,75,77,82,86,103 2030-2470-0CAP,CERAMIC AXIAL,47,5%,50V1C89A 2030-2473-0CAP,CERAMIC AXIAL XR7,473,10%,50V6C19,31,33,36,55,58 2030-2474-0CAP,CERAMIC AXIAL Z5U,474,20%,50V1C126 2030-2561-0CAP,CERAMIC AXIAL,561,10%,50V1C115 2031-1227-0CAP,ELECTROLYTIC RADIAL,227,-10%+50%,25V13C3,53,54,59,85,97,100,108,112,116,118,120A, 125 2031-2227-0CAP,ELECTROLYTIC RADIAL,227,-10%+50%,50V1C107 2031-2335-0CAP,ELECTROLYTIC RADIAL,335,20%,50V45C3A,4,5,7,8,9,10,11,14,15,16,17,18,24,27,30, 35,37,38,39,40,42,43,44,45,60,61,66,70,80,87, 88,89,90,91,92,93,95,98,99,113,114,117,123, 124 2038-2478-0CAP,ELECTROLYTIC AXIAL,478,20%,50V2C101,102 2051-0100-0RES,CARBON FILM,1 OHM,1/4W,5%47R6,11,13,28,34,36,42,46,47,52,53,63,69,70,73, 79,81,83,85,88,92,105,107,111,116,117,123, 162,168,169,171,173,174,175,177,186,211, 222,240,243,261,265,267,283,292,303,304 2051-0101-0RES,CARBON FILM,10 OHM,1/4W,5%5R127,130,132,133,224 2051-0221-0RES,CARBON FILM,22 OHM,1/4W,5%1R277 2051-0470-0RES,CARBON FILM, 4.7 OHM,1/4W,5%2R237,247 2051-1001-0RES,CARBON FILM,100 OHM,1/4W,5%2R226,244 2051-1002-0RES,CARBON FILM,1K OHM,1/4W,5%12R3,9,12,93,104,134,193,206,212,232,266,284 2051-1004-0RES,CARBON FILM,100K OHM,1/4W,5%38R7,10,15,19,29,32,58,60,80,82,84,106,138,141, 157,161,164,172,178,180,185,188,190,191,192, 209,210,257,258,260,270,271,272,287,288,291, 295,297 2051-1005-0RES,CARBON FILM,1M OHM,1/4W,5%9R2,40,51,68,90,91,94,95,198 2051-1203-0RES,CARBON FILM,12K OHM,1/4W,5%23R1,26,43,76,97,109,112,125,128,131,152,153, 154,155,203,213,214,215,242,268,281,282,298 LVLPART#DESCRIPTIONQTYREF. DESIG. 2051-1204-0RES,CARBON FILM,120K OHM,1/4W,5%5R187,256,259,269,289 2051-1504-0RES,CARBON FILM,150K OHM,1/4W,5%2R252,255 2051-2202-0RES,CARBON FILM,2.2K OHM,1/4W,5%8R8,41,118,124,149,150,197,229,246 2051-2203-0RES,CARBON FILM,22K OHM,1/4W,5%29R4,31,35,37,39,45,49,50,54,57,59,62,66,71,72, 86,87,89,100,108,110,113,115,120,176,194, 205,238,245,280 2051-2204-0RES,CARBON FILM,220K OHM,1/4W,5%4R216,217,219,221 2051-2206-0RES,CARBON FILM,22M OHM,1/4W,5%1R16 2051-3302-0RES,CARBON FILM,3.3K OHM,1/4W,5%6R135,136,230,231,248,279 2051-3303-0RES,CARBON FILM,33K OHM,1/4W,5%16R30,114,119,122,139,140,145,151,158,163,165, 170,181,189,278,299 2051-3304-0RES,CARBON FILM,330K OHM,1/4W,5%2R144,199 2051-3904-0RES,CARBON FILM,390K OHM,1/4W,5%2R143,179 2051-4701-0RES,CARBON FILM,470 OHM,1/4W,5%5R218,220,225,227,228 2051-4702-0RES,CARBON FILM,4.7K OHM,1/4W,5%6R126,129,148,156,207,208 2051-4703-0RES,CARBON FILM,47K OHM,1/4W,5%16R20,21,25,55,74,99,101,137,142,159,160,166, 167,182,183,202 2051-4704-0RES,CARBON FILM,470K OHM,1/4W,5%1R98 2051-5602-0RES,CARBON FILM,5.6K OHM,1/4W,5%21R17,18,23,24,27,44,48,56,61,64,65,75,78,196, 200,273,274,276,285,286,296 2051-5603-0RES,CARBON FILM,56K OHM,1/4W,5%8R14,38,204,251,253,254,262,263,264 2052-1213-0RES,METAL FILM,12.1K OHM,1/4W,1%8R290,293,300,302,305,306,307,308 2054-2702-0RES,CARBON FILM,2.7K OHM,1W,5%4R195,235,236,241 2056-.330-0RES,CERAMIC WW,.33 OHM,5W,10%4R223,234,249,250 2056-0500-0RES,CERAMIC WW,5 OHM,5W,10%1R239 2070-0508-0POT,1K TRIM,6MM,SLOT,.3W1R233 2070-0509-0POT,20K TRIM,6MM,SLOT,.3W6R5,146,147,201,294,301 2070-0514-0POT,50KB,LINEAR,9MM,METAL KNURL 9MM,.16R22,33,67,77,96,102- all other pots 2070-0523-0POT,2X50K LIN,9MM,METAL KNURL NOBLE.051R121- master pot 2090-0010-0SWITCH,PP,DPDT,6A,PC TERM1S9 2090-0014-0SWITCH,PP,DPDT,.2A,BREAK/MAKE,PC MOUNT 10all other switches 2092-0201-0JACK SW-RN112APC,1/4,S-TIP,SLDR TERM4 2092-0203-0JACK SW-RN111PC,1/4,O-TIP,P.C. TERM2 2092-0204-0JACK SW-RN112BPC,1/4,O-TIP,O-RING,P.C.2 2093-0028-0HEADER,3X.156,MALE,LOCK2