HK_actor_dx112a_sat_service_manual_HK1104电路图.pdf

Service Documents Confidential, for authorized service technicians only! Do not disclose this information to or share these documents with third parties. Vertraulich! Nur fr autorisierte Servicetechniker! Nicht zur Weitergabe an Dritte freigegeben! TECHNICAL SERVICE: Stamer Musikanlagen GmbH Magdeburger Str. 8 66606 St.Wendel Germany Music it is an end-to-end sound reinforcement solution consisting of sub- woofers, mid/high units and meticulously matched electronic circuitry. Our engineers developed new technologies to satisfy the stringent requirements of such an advanced system. With its unique and sophisticated features, every active HK AUDIOsound reinforcement system stands out in the crowd of far more basic active cabinets. All the best from the HK AUDIO team; enjoy your ACTOR DX system! Warranty Register your ACTOR DX using the enclosed warranty card to extend your warranty to fi ve years free of charge! Use the convenient online registration option at . If you are unable to register online, please fi ll out the enclosed warranty card completely and mail or fax it to us. The registration is only valid if the warranty registration card is fi lled out and returned to HK AUDIOor the device is registered via the Internet within 30 days of the date of purchase. We are also interested in learning where our devices are used and by whom. This information will help us design future products. Your information is of course protected by privacy laws. Thank you! HK AUDIO Technical Service Postfach 1509 D-66959 St. Wendel Germany Table of Contents 1 ACTOR DX System Components . . . . . . . . . . . .6 2 Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 3 Setup and Cable Connections . . . . . . . . . . . . . . .6 4 Connections and Control Features . . . . . . . . . . .8 5 Tips and Tricks . . . . . . . . . . . . . . . . . . . . . . . . .10 6 ACTOR DX Accessories . . . . . . . . . . . . . . . . . . .11 7 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .11 8 Technical Specifi cations . . . . . . . . . . . . . . . . . . .12 RadioFans.CN 收音机爱 好者资料库 5 English Unique features for premium performance Digital amping for enhanced effi ciency and dynamics With an extremely high effi ciency rating topping the 90% mark, Class D digital power amps are substantially smaller, lighter, and more compact than comparable conventional amps. The reduced thermal load on components enhances reliability, while the far faster slew rate and higher attenuation factor audibly enhance the speed and accuracy of the systems dynamic response. DDO Controller technology The DDO Controller compensates for varying response of components such as low-frequency, midrange and high-frequency speakers, power amps, crossovers and so forth to forge a homogenous system with uniform dynamics and a sonic image with sharply defi ned contours. DuoTilt making the most of sonic energy The novel DuoTilt pole mount allows sound energy to be utilized far more effi ciently. DuoTilt offers 7.5 and 15 angles of tilt, enabling perfect mid/high unit-to-audience alignment. Troublesome ceiling refl ections are minimized, making the sound clearer, tighter, and more focused. Easy Setup and Handling for less pre-gig stress Like all HK AUDIO Active Systems, ACTOR DX was designed as a cohesive system consisting of perfectly matched components. Painstaking effort was invested in ensuring ACTOR DX can be trans- ported easily and set up quickly. Handling and EQing couldnt be any easier, with no complicated and time-consuming tweaking challenges to master. ACTOR DX Manual 1.1 1 ACTOR DX System Components ADX 112 A Mid/High Unit These enclosures are loaded with one 12 HK AUDIO Custom speaker and one 1. 4 compression driver with a 60 x 40 CD horn. Delivering 600 W RMS, the Class D power amp is housed in a separate chamber along with the DDO Controller. ADX 115 Sub A Subwoofer The ACTOR DX A Subs housing is split up into two chambers. The front chamber serves as the speaker cabinet for the 15 front-loaded loudspeaker, which has a power handling capacity of 500 W RMS and a nominal impedance of 8 ohms. The power amp is housed in a separate compartment at the rear of the cabinet. ADX 115 Sub B Subwoofer The housings and speakers of the ADX 115 Sub Bs and Sub A are identical. The Sub B is the passive version of the Sub A. 2 Transport To transport the system, simply set the subwoofers on their casters and place the mid/high units onto the subwoofers with the foam rubber grille side facing down. Use original HK AUDIO covers to get your system ready to handle the rigors of the road. Padded and protected against moisture, your ACTOR DX system is sure to serve you well for a long time to come. 3 Setup and Cable Connections 3.1 The Standard ACTOR DX System The standard system comprises two ACTOR ADX 112 A mid/high units, two ADX 115 Sub A subwoofers and two ADX 115 Sub B subwoofers. Always connect ACTOR DX starting at the top and working your way down (refer to the diagram on the rear panel of ACTOR DX components)! This may seem unusual if you are accustomed to working with active systems where signals are routed via paralleled pass-through jacks, which would allow connections to be made in any sequence. ACTOR DX, in contrast, features the DDO System Controller housed in the ADX 112 A mid/high unit. This controller lets you determine basic settings such as the system confi guration, the mid/high units level and the subwoofers level right on the mid/high unit. DDO then routes signals from the mid/high unit to Sub A. Note: Always connect cords in the correct sequence. Never connect a cord carrying a signal from a mixer directly to Sub A because this bypasses the DDO system controller! Always connect signal sources to the “master” system input located on ACTOR DX mid/high units! 3.2 ACTOR DX Full-range Setup The full-range setup comprises two ACTOR ADX 112 A mid/high units. Select the appropriate system confi guration on the system controllers control panel. In full-range mode, the subwoofer output (DDO controlled) is disabled to prevent handling errors. 3.3 ACTOR DX Club Set The club set comprises two ACTOR ADX 112 A mid/high units and two ADX 115 Sub A bins. ADX 112 A ADX 115 Sub A ADX 115 Sub B Standard system connections Connections for full-range setup 7 English 3.4 Dual ACTOR DX System The dual system comprises four ACTOR ADX 112 A mid/high units, four ADX 115 Sub A bins and four ADX 115 B Sub bins. Connect cables from top to bottom as described above. Plug a microphone cord into the fi rst mid/high units THROUGH port to route the mixer signal to the second ACTOR DX stack. Ensure XLR connectors are wired as follows: 1= ground, 2= +, 3= - 3.5 Flying ACTOR ADX 112 A Mid/High Units Use the HK AUDIO rigging frame to fl y ACTOR DX mid/high units. To attach the frame, remove the countersunk M10 hex head bolts from the side panels. Bolt the rigging frames brackets to the enclosure. Set the mid/high units inclination to the desired angle by loosening the knobs on the sides and fi rmly hand-tightening them again. The serrated plastic washers hold the mid/high unit in place. Note: For reasons of safety, use tested and certifi ed load-securing devices only (for example, half- couplers, TV spigots, brackets, and so forth)! Ensure wall and pole mounts are designed to handle the load (an ACTOR ADX 112 A weighs 30 kg). 3.6 Using the ACTOR DX Tilt Unit Using the optional tilt unit couldnt be easier: Proceed as if mounting the enclosure on a pole. Set the ACTOR DX tilt unit with the bottom plate facing down on the upper subwoofer and then set the ACTOR mid/high unit on it so the tilt units rod is inserted into one of the two holes (7.5 or 15). Question Can I connect speakers other than an ACTOR DX mid/high unit to an ACTOR DX Sub A or Sub B subwoofer? Answer The system components are acoustically matched for optimum audio performance and may be operated in the indicated confi guration only. Using other mid/high units can degrade the sound and damage the power amp (e.g. the Sub As). Sub As nominal impedance is 4 ohms, and impedance may not fall short of this value. Connect no more than one Sub B to Sub As speaker out. Club set connections Dual system connections ACTOR ADX 112 A with rigging bracket The ACTOR DX tilt unit in action ACTOR DX Manual 1.1 4 Connections and Control Features 4.1 ACTOR ADX 112 A 1 Power Switch Handling: This is the on/off switch for the active system. When engaged, the system controllers display lights up orange. Always switch the ACTOR DX active system on last, that is, after powering up all other components, and switch it off fi rst before powering down all other connected devices. 2 Mains Input Connecting cords: Use the factory-included Power- con cable to connect this socket to a wall receptacle. Caution! Make sure the local mains voltage matches the voltage specifi ed on the device. If you connect the system to the wrong mains voltage, you may destroy the ACTOR DX systems electronic components. 3 Link (only 220-240 V version) Connecting cords: The Powercon Link socket is wired in parallel to the Mains Input. Connect other load consumers (for example, another ACTOR DX mid/high unit or an ACTOR DX Sub A bin) to it. Heads up: The Powercon Link socket can handle loads up to 8.6 A and 2060 W (at 230 volts). This means you can use it to power up to but no more than two additional ACTOR DX components. Note: Always switch on ACTOR DX components one after another to prevent a sudden spike in the venues power supply. Otherwise the power surge may cause the house circuit breaker to trip. 4 Ground Ground lift button for separating the signal and chassis ground in the event of humming noises. In the event of low-frequency hum, engage the Ground Lift switch. The ground circuit is severed when this button is pressed. If this doesnt solve the problem, check all cords connected to ACTOR DX as well as all signal cables routed to the mixing console for damage (see also Tips and Tricks). 5 Input Sensitivity This selector matches the preamps input sensitivity to the mixers output signal level. Engage this switch to select either -10 dB (for exam- ple, for unbalanced 1/4” jacks and consumer level devices) or +0 dB (for example, for balanced XLR ports and professional mixers). Recommendation: Select +0 dB when using a professional-grade mixer sporting balanced outputs. This lets you take advantage of console faders full control range and helps prevent overloads. Opt for -10 dB A when using a console with a lower output level (unbalanced 1/4 output). 6 Input Overload This LED lights up when the input level is too high and the entire system (preamp and controller) is being overdriven. Not only does this result in unpleasant distortion, it can also harm the systems components. If the red LED lights up, reduce the level (volume) at the mixer! 7 Line In Connecting cords: Connect cords carrying signals from your mixer (master left/right, line out, or a similar circuit) to the balanced inputs using a mic cord equipped with XLR connectors. Ensure XLR connectors are wired as follows: 1= ground, 2= +, 3= -. 8 Through Connecting cords: Use this parallel output to route the incoming line signal to other components (for example, to additional ACTOR DX mid/high units) via XLR cords. 9 Limiter LEDs These are the active systems rev counters, serving to indicate the limiters operating status. 10 Subwoofer Output Connecting cords: Use this output to send the subwoofer signal from the DDO controller to an ACTOR ADX 115 Sub A via an XLR cord. Ensure XLR connectors are wired as follows: 1= ground, 2= +, 3= -. ACTOR ADX 112 A 1 4 6 7 8 10 9 9 5 11 12 13 14 2 3 9 English 11 Display Read-out: The numeric display indicates the currently selected system confi guration. 0 Mute 1 Top only1 mid/high unit Full-range mode 2 Half Stack DJ1 mid/high unit, 1 Sub A 3 Half Stack Band 1 mid/high unit, 1 Sub A 4 Full Stack DJ1 mid/high unit, 1 Sub A+ Sub B 5 Full Stack Band1 mid/high unit, 1 Sub A+ Sub B 6 Dual Stack DJ2 mid/high units, 2 Sub A+ Sub B 7 Dual Stack Band 2 mid/high units, 2 Sub A + Sub B L Lockedbuttons are disabled UUnlockedbuttons are enabled 12 Up/Down Buttons Use these buttons to select system confi gurations. Operation: To enable the buttons, press Up and Down simultaneously and hold for about one to two seconds. The letter U (for unlocked) appears briefl y in the display. Now you can press Up and/or Down to select the desired setup (see the table above). The buttons are automatically disabled soon thereafter. The letter L (locked) appears briefl y in the display. 13 Top Level Operation: Use this knob to determine the volume of the mid/high unit. The standard setting is 0 dB at the 12 oclock position. This means the level is neither boosted nor cut. 14 Subwoofer Level Operation: When the knob is set to the 12 oclock position, the subwoofers and the mid/high units respective volumes are matched, ensuring bass and mid/high ranges are rendered in balanced musical proportion. If desired, twist the Subwoofer Level knob to the left to decrease and to the right to increase the subwoofers level by up to 6 dB. Tip: If necessary or desired, use the Subwoofer Level knob to boost or cut bass frequencies below 100 Hz rather than resorting to the mixers master EQ. 15 Rigging Points Attach the ACTOR DX rigging frame here to fl y the mid/high unit from a truss or similar suspension device. ACTOR ADX 112 A control features Control features of the ACTOR DX system controller 1 2 3 4 6 7 8 10 5 9 9 11 11 12 9 9 12 13 14 13 14 More about limiter LEDs A dedicated LED indicates the limiter status for the mid/high-range signal path and the subwoofer circuit, respectively. What do the lights mean? The green LED indicates that the given input is receiving a signal. As long as the LED lights up green, the system is operating at low-to-medium levels, with plenty of headroom available for the power amps. Yellow indicates that the system is being pushed close to its threshold. The yellow LED may fl ash at regular intervals, but it may not illuminate continuously. If it does this, back off the volume on your mixer. If the LED constantly lights up red, there is a problem in the power amp and the system will shut down. In this case, have a qualifi ed service technician check the device. ACTOR DX Manual 1.1 4.2 ACTOR ADX 115 Sub A 1 Power Switch Operation: This is the on/off switch for the active system. When engaged, the Power On LED lights up red. Always switch the ACTOR DX active system on last, that is, after powering up all other components, and switch it off fi rst before powering down all other connected devices. 2 Mains Input Connecting cords: Use the factory-included Power- con cord to connect this socket to a wall receptacle. Caution! Make sure the local mains voltage matches the voltage specifi ed on the device. If you connect the system to the wrong mains voltage, you may des