studer AOpen_i915_Manual 电路图.pdf

RadioFans.CN 收音机爱 好者资料库 1 Table of Contents Table of Contents . 1 1.1 A Thank-you Note Before You Get Start.4 1.2 Features of This Manual .5 1.3 Safety Information .5 Chapter 2 Introduction to This Motherboard. 6 2.1 How does your motherboard look like?.6 2.2 Specification.7 2.3 Block Diagram .8 Chapter 3 Hardware Installation. 9 3.1 Quick Installation Procedure .9 3.2 Installation You Have to Know.10 Installing CPU.10 Installing CPU Cooler .11 Installing CPU and System Fans.14 Installing Memory Modules .15 Connecting IDE and Floppy Cables .16 Connecting Front Panel Cable .17 Connecting ATX Power Cables.18 3.3 Other Installation for Your Reference .19 Setting CPU Voltage and Frequency.19 Connecting Serial ATA.20 Connecting PCI express x16 Graphics Slot.21 Connecting PCI Express x 1 Slot.23 Connecting IrDA.24 Dual Gigabit LAN Supported .25 Connecting USB2.0.26 Connecting 1394.27 Super 7.1 Channel Audio Effect.28 RadioFans.CN 收音机爱 好者资料库 2 Connecting Front Audio.29 Connecting CD_IN.30 Connecting COM1/COM2 .31 Connecting Case Open.32 Connecting S/PDIF (Sony/Philips Digital Interface) .33 Connecting PS2 Keyboard .34 Colored Coded Back Panel .35 LED Indication .36 3.4 Jumper Settings.37 Chapter 4 Special Features and Utilities. 38 4.1 RAID (Redundant Array of Independent Disks).38 RAID BIOS Setting Utility .38 4.2 Other Useful Features .42 Chapter 5 Setting BIOS. 43 5.1 Introduction .43 5.2 How To Use Phoenix-Award BIOS Setup Program.44 5.3 How To Enter BIOS Setup.44 Standard CMOS Features .45 Advanced BIOS Features.47 Advanced Chipset Features.49 Integrated Peripherals .51 Power Management Setup.56 PNP/PCI Configurations.58 Silent BIOS/HW Monitor.59 Frequency/Voltage Control .60 Load Setup Defaults .61 Load Turbo Defaults .61 Set Password.62 Save higher clock setting may cause serious system damage. 20 Connecting Serial ATA To connect a serial ATA disk, you have to have a 7-pin serial ATA cable. Connect two ends of the serial ATA cable to the serial ATA header on the motherboard and the disk. Like every other traditional disk, you also have to connect a power cable. Please be noted that it is a jumper free implement; you dont need to set jumpers to define a master or slave disk. When serial ATA hard disks are installed on serial ATA ports, the one connected on Port0 (SATA1) will be set as the first boot device automatically. Note 1: SATA1 and SATA2 dont support Hot-Plug in function. SATA3 and SATA4 support Hot-Plug Note 2: SATA1 and SATA2 support SATA I SATA3 and SATA4 support SATA II SATA1 SATA2 SATA4 SATA3 21 Connecting PCI express x16 Graphics Slot This motherboard provides a PCI Express x 16 Graphics slot, a black slot having the latest PCI Express x 16 specification on motherboard. The PCI Express x 16 is a bus interface targeted for high-performance 3D graphic. Traditionally AGP used both rising and falling edge of the 66MHz clock for 8X AGP, and the data transfer rate could achieve 2.1GB/s. Now PCI Express x 16 is moving to higher data transfer rate, which is upgraded to 8.0GB/s (250MB/s x 16 x 2, its 4.0GB/s per direction). JP92 JP88 HDTV On On PCIeX16 Off Off JP91 JP83 DVI On On PCIeX16 Off Off PCIex16 JP92 JP91 JP83 JP88 22 If user plugs a PCI Express x 16 Graphics, you must remove jumper beside PCI Express x 16 Slot. Remove Jumper Warning: If user doesnt remove jumper, it might make system instable. 23 Connecting PCI Express x 1 Slot This motherboard provides one PCI Express x 1 slot, which is located between the PCI Express x 16 and traditional PCI slot. In order to go with the step of todays and tomorrows processors, PCI Express x 1 provides higher I/O bandwidth. The transfer data rate could achieve 500MB/s concurrently (its 250MB/s per direction), which is nearly 4 times faster than the traditional PCI. You could install any PCI Express x 1 device in these slots for your preference. PCIex1 24 Connecting IrDA The IrDA connector can be configured to support wireless infrared module, with this module and application software such as Laplink or Windows Direct Cable Connection, user can transfer files to or from laptops, notebooks, PDA devices and printers. This connector supports both HPSIR (115.2Kbps, 2 meters) and ASK-IR (56Kbps). Install an infrared module onto the IrDA connector and enable the infrared function from BIOS Setup, UART Mode, you can use this function. Please make sure you connect correct orientation when plugging IrDA module. NC +5V IR_TX Pin 1 KEY GND IR_RX IrDA Connector 1 25 Dual Gigabit LAN Supported On the strength of dual Gigabit LAN controller on board, this motherboard provides 10/100/1000Mbps Ethernet for office and home use. The Ethernet RJ45 connector is located on the top of USB connectors. The right hand side LED indicates link mode; it lights in yellow when linking to network. The left hand side LED indicates the transfer mode and will light in green when data is transferring at 100Mbps (never lights while at 10Mbps), but will light in orange when transferring in Gigabits mode. To enable or disable this function, you may simply adjust it through BIOS. To enable LAN wakeup function, you have to set the “Wake on PCI Card” enable in the BIOS “Power Management Setup” section. Speed LED (Left) Green 100Mbps Orange Gigabit mode ACT LED (Right) Yellow 26 Connecting USB2.0 This motherboard provides eight USB 2.0 ports to connect USB devices such as mouse, keyboard, modem, printer, etc. There are four ports on the back panel. You can use proper cables to connect Front USB connector to USB modules or chassis front panel. Pin 1 Pin 1 27 Connecting 1394 With IEEE1394 Chip on board (AGERE 1394), having its data transfer rate up to 400Mb/s, this interface can connect to devices that require high data transferring performance such as digital camera, scanner or others IEEE 1394 devices. Please use appropriate cables to connect IEEE1394 devices. Pin1 Pin1 Warning: Please note that Hot-Plug is not allowed on IEEE 1394 headers; doing so will burn the controller IC and damage the motherboard. 1 9 10 TPA- GND TPB- +12V (Fused) TPA+ GND TPB+ +12V (Fused) SHIED GND IEEE 1394 Connector 2 28 Super 7.1 Channel Audio Effect This motherboard comes with an ALC880 CODEC, which supports the latest 7.1 Channel with high quality of audio effects, bringing you a brand new audio experience. This motherboard provides 7.1 Channel ports shown as below. Picture represents the standard location of all speakers in 7.1 Channel sound tracks. Please connect the plug of your front speakers to the green “Speaker out” port , rear surround speakers to orange port, side surround speakers to gray port and both of the center and subwoofer speakers to black port on the back panel. 29 Connecting Front Audio If the housing is designed with an audio port on the front panel, youll be able to connect onboard audio to front panel through this connector. By the way, please remove the jumper cap from the Front Audio Connector before you connect the cable. Do not remove this yellow jumper cap if your housing doesnt have an audio port on the front panel. AUD_GND AUD_VCC 1 Front Audio Connector AUD_RET_R KEY AUD_FPOUT_L NC AUD_FPOUT_R AUD MIC BIAS AUD_MIC AUD_RET_L Pin1 30 Connecting CD_IN This connector is designed to connect CD Audio cable from CDROM or DVD drive to onboard sound. L R GND GND CD-IN Connector 31 SIN DTR# DSR CTS# DCD# SOUT GND RTS# R1# Connecting COM1/COM2 This motherboard provides two serial ports. All of them are on the left of PCI32 slot. With proper cable, you can connect it to the back panel of chassis. Pin 1 Pin 1 1 32 Connecting Case Open The “CASE OPEN” header provides chassis intrusion-monitoring function. To make this function work, you have to enable it in the system BIOS, connect this header to a sensor somewhere on the chassis. So, whenever the sensor is triggered by lights or by the opening of the chassis, the system will beep to inform you. Please be informed that this useful function only applies to advanced chassis; you may purchase an extra sensor, attach it on your chassis and make a good use of this function. Pin 1 1 Sensor GND Chassis Intrusion Connector 33 Connecting S/PDIF (Sony/Philips Digital Interface) S/PDIF (Sony/Philips Digital Interface) is a newest audio transfer file format, which provides impressive audio quality through optical fiber and allows you to enjoy digital audio instead of analog audio. Through a specific converter, you can connect the S/PDIF connector to other end of the S/PDIF audio module, which bears S/PDIF digital input/output. However, you must have an S/PDIF supported speaker/amplifier/decoder with S/PDIF digital input/output to connect to the S/PDIF digital input/output to make the most out of this function. SPDIF IN SPDIF Output Converter 34 Connecting PS2 Keyboard This connector is designed to connect PS2 Keyboard to support legacy device. 1 Plug into by following connector color Green Red Brown Yellow 35 Rear SUR/ S/PDIF-Out Colored Coded Back Panel The onboard I/O devices have AC97 sound, VGA Port, DVI Connector, YPbPr Connector, S-Video, RJ-45 LAN Connector and USB Port. The view angle of drawing shown here is from the back panel of the housing. Line-In / SPDIF-In : Comes from the signal sources, such as CD/Tape player. Rear SUR / SPDIF out: For rear surround speaker. Center/Subwoofer: For center this menu allows you to configure the system parameters and save the configuration into the 128 bytes CMOS area (normally in the RTC chip or in the main chipset). The Phoenix-Award BIOS that installed in the Flash ROM of the motherboard is a custom version of an industry standard BIOS. The BIOS provides critical low-level support for standard devices such as hard disk drives, serial and parallel ports. AOpens R and Slow give more stable performance. This field applies only when synchronous DRAM is installed in the system. Available options: 2, 3, 4, 5 Warning: Make sure you fully understand the items contained in this menu before you try to change anything. You may change the parameter settings to improve system performance. However, it may cause your system to be unstable if the setting is not correct for your system configuration. 50 Advanced Chipset features DRAM RAS# Precharge If an insufficient number of cycles are allowed for the RAS to accumulate its charge before DRAM refresh, the r