Yamaha_UD-Stomp 电路图.pdf

UD-Stomp 1 SERVICE MANUAL GA 011631 1.338K-476 Printed in Japan 2002.3 HAMAMATSU, JAPAN CONTENTS SPECIFICATIONS. 3 PANEL LAYOUT . 4 CIRCUIT BOARD LAYOUT . 6 WIRING. 7 BLOCK DIAGRAM.8 DISASSEMBLY PROCEDURE . 10 LSI PIN DESCRIPTION. 13 IC BLOCK DIAGRAM . 16 CIRCUIT BOARDS. 18 TEST PROGRAM . 26 ERROR MESSAGES . 28 MIDI IMPLEMENTATION CHART . 29 PARTS LIST OVERALL CIRCUIT DIAGRAM This document is printed on chlorine free (ECF) paper with soy ink. RadioFans.CN 收音机爱 好者资料库 UD-Stomp 2 IMPOR TANT NOTICE This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and under- stood by the users, and have therefore not been restated. WARNING :Failure to follow appropriate service and safety procedures when servicing this product may result in per- sonal injury, destruction of expensive components and failure of the product to perform as specified. For these reasons, we advise all Yamaha product owners that all service required should be performed by an authorized Yamaha Retailer or the appointed service representative. IMPORTANT :This presentation or sale of this manual to any individual or firm does not constitute authorization certifi- cation, recognition of any applicable technical capabilities, or establish a principal-agent relationship of any form. The data provided is belived to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, and service departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable and changes in specification are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING :Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground bus in the unit (heavy gauge black wires connect to this bus.) IMPORTANT :Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the unit. WARNING: CHEMICAL CONTENT NOTICE! The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (Where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT SO EVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food. WARNING Components having special characteristics are marked and must be replaced with parts having specification equal to those originally installed. LITHIUM BATTERY HANDLING This product uses a lithium battery for memory back-up. WARNING :Lithium batteries are dangerous because they can be exploded by improper handling. Observe the following pre- cautions when handling or replacing lithium batteries. Leave lithium battery replacement to qualified service personnel. Always replace with batteries of the same type. When installing on the PC board by soldering, solder using the connection terminals provided on the battery cells. Never solder directly to the cells. Perform the soldering as quickly as possible. Never reverse the battery polarities when installing. Do not short the batteries. Do not attempt to recharge these batteries. Do not disasemble the batteries. Never heat batteries or throw them into fire. ADVARSEL! Lithiumbatteri-Eksplosionsfare ved fejlagtig handtering. Udskiftning ma kun ske med batteri af samme fabrikat og type. lever det brugte batteri tilbage til leverandren. VARNING Explosionsfara vid felaktigt batteribyte. Anvand samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera anvant batteri enligt fabrikantens instruktion. VAROITUS Paristo voi rajahtaa, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiiin. Havita kaytetty paristo valmistajan ohjeiden mukaisesti. The following information complies with Dutch official Gazette 1995. 45; ESSENTIALS OF ORDER ON THE COLLECTION OF BATTERIES. Please refer to the diassembly procedure for the removal of Back-up Battery. Leest u voor het verwijderen van de backup batterij deze beschrijving. RadioFans.CN 收音机爱 好者资料库 UD-Stomp 3 SPECIFICATIONS Digital Section 8-Band Delay (Delay Time: 696msec max per band) Delay Time, Loop Filter (High Cut, Low Cut), Feedback, Tap, Pan, Level parameters can be set for each individual Effect Band. Effect Bands can be connected in series or parallel Effect Bands can be grouped together Maximum delay time (8 bands grouped) is 5890msec The same number of delay outputs as the number of delays used in the Group are available. Tap Tempo Function (Delay Time) Loop Sampling Function Individual Modulation Settings (Speed, Depth) for each Effect Band are available. Two types of modulation waves can be set simultaneously (Sine + Triangle/Saw Up/Saw Down). Modulation sync between bands is available. MIDI Functions Receive: Program Change (Program Change Table can be created), Control Change, Bulk In Transmit: Program Change, Control Change, Bulk Out, Merge Out Controller Switch Top Panel Push Switch x17 UP, DOWN, UTILITY, STORE, EFFECT BAND (1 - 8), CONNECT, GROUP, SYNC, WAVE, FUNCTION Knob x14 ASSIGNABLE CONTROL, TIME COARSE, TIME FINE, LOW CUT FILTER, HIGH CUT FILTER, FEEDBACK, DIRECT LEVEL/PAN, TAP, SPEED, DEPTH, PAN, LEVEL, EFFECT LEVEL, OUTPUT Footswitch x4 1, 2, 3, BANK Rear Panel STAND-BY ON/OFF, INPUT LOW/HIGH Display 7 Segment LED (3 digit) x1 Push Switch LED x17 Foot Switch LED x4 Connections/Jacks INPUT: Standard Monaural Phone Jack OUTPUT L/MONO, R: Standard Monaural Phone Jack PHONES: Standard Stereo Phone Jack EXP. PEDAL: Standard Stereo Phone Jack DIGITAL OUT: COAXIAL (Samplling Rate : 44.1 kHz) MIDI IN, MIDI OUT: 5 pin DIN A/D Converter 20 bit + 3 bit Floating D/A Converter 20 bit Sampling Frequency 44.1 kHz Memory Allocations Preset: 90 User: 90 Input Level/Impedance (When using preamp bypass) INPUT HIGH: -25dBm/1M INPUT LOW: -15dBm/1M Output Level/Impedance OUTPUT L/MONO, R: 0dBm/1k PHONES: 0dBm/47 (47 load) Power Exclusive Power Adaptor (AC-10) AC Output: AC12V, 1000mA Power Consumption 15W Dimensions (WxHxD) 280 x70 x184mm (11.0”x2.8”x7.2”) Weight 2.2kg (4lbs 14oz) Accessories Power Adaptor (AC-10) Owners Manual RadioFans.CN 收音机爱 好者资料库 UD-Stomp 4 Top Panel PANEL LAYOUT 1 2 3 4 5 Up Button (UP) Down Button (DOWN) Utility Button (UTILITY) Store Button (STORE) Display Display & Main Section Footswitch Section Display & Main SectionController Section q w e r t UD-Stomp 5 6 7 8 9 10 11 12 13 Controller Section ASSIGNABLE CONTROL EFFECT BAND 1-8 EDIT FUNCTION Delay Time Control: Coarse (TIME COARSE) Delay Time Control: Fine (TIME FINE) LOW CUT FILTER Control HIGH CUT FILTER Control FEEDBACK Control y 1 Footswitch Section u i !4!5!6!7!8 o!0!1!2!3 !9 0 14 15 16 17 18 19 20 21 TAP Control SPEED Control DEPTH Control PAN Control Delay Level Control (LEVEL) EFFECT LEVEL Control DIRECT LEVEL/DIRECT PAN Control OUTPUT Level Control 2 3 22 23 Footswitches 1, 2, 3 Bank Switch (BYPASS, BANK, TAP TEMPO) UD-Stomp 6 24 25 26 27 28 Power Switch (STAND-BY ON/OFF) Power Adaptor Jack (AC IN 12V 1A) MIDI OUT Jack MIDI IN Jack DIGITAL OUT Jack Rear Panel 45789#0#3#2#16 29 30 31 32 33 Expression Pedal Jack (EXP. PEDAL) Headphones Jack (PHONES) Output Jacks (OUTPUT R, L/MONO) Input Level Switch (LOW/HIGH) INPUT Jack CIRCUIT BOARD LAYOUT 1/2 2/2 PN DM PN UD-Stomp 7 WIRING V839830 1 1/2 2/2 (V611470) (V610850) (V611460) (V611450) CN301CN304 CN1CN2CN3 CN310CN309 CN308 CN307 CN303 CN103 CN302 Shield Sheet CN305 CN306 (V611480) PN DM PN Note) When installing the DM circuit board, use care not to have the wire assembly caught by the bottom case. UD-Stomp 8 BLOCK DIAGRAM DM PN1/2 PN1/2 PN2/2 A A IC101 SW101 IC103IC103 IC102IC102 312167 2167 5 6 3 4 26 27 X2 X1 IC1 IC2, IC3 IC104 IC12 IC10, IC11 IC8 SW-R0R3 PN-PB0PB7 (DM1/2-CN1) CN103 CN301 CN301 VR314 (PN1/2-CN304) DOUT 16 (DM-CN3) (PN1/2-CN302) AN0AN3, SELECT A, SELECT B 2 4 1 UD-Stomp 9 PN1/2 PN2/2 A A IC105 31 IC105 57 IC106 31 IC106 57 2 3 1 2 3 1 2 4 1 2 4 1 TRS BALANCE OUT TRS BALANCE OUT CN301 CN103 CN301 VR314 IC112, IC113, IC114 SW-001 (DM-CN2) (PN1/2-CN303) LED-MOD LED-REV LED-FOOT SW-010 SW-100 SW-LINE 15,17 RXDO, TXDO KEC-54241 1 UD-Stomp 10 Battery Battery holder DISASSEMBLY PROCEDURE Fig.1 30:Bind Head Tapping Screw-B 3.0 x8 MFZN2BL (EP600190) 2.DM Circuit Board (Manhour requirement: 6 min.) 2-1.Remove the bottom case. (See Procedure 1.) 2-2.Remove the one (1) screw marked T110A, three (3) screws marked T120, five (5) hexagonal nuts marked T50 and five (5) flat washers marked T60 from the rear panel and the three (3) screws marked T110B from the DM circuit board. The DM circuit board can then be removed. Remove the five (5) toothed washer internal tooth forms marked T70 as well when removing the DM circuit board from the main body. (Fig. 2) Bottom 30 30 T110A T50T60T120 Rear T50:Hexagonal Nut 9.0 12x2 MFNI33 (LX200060) T60:Flat Washer 9x14 0.5 FNM3 (VL802300) T110:Bind Head Tapping Screw-B 3.0 x8 MFZN2BL (EP600190) T120:Bind Head Tapping Screw-P 3.0 x12 MFZN2BL (VC161100) 1.Bottom Case (Manhour requirement: 1 min.) Remove the six (6) screws marked 30. The bottom case can then be removed. (Fig. 1) Battery VS246400 VS246300(Battery holder for VS246400) Notice for back-up battery removal Push against the holder hook, then the battery will pop up. Druk tegen de houder, de batterij springt dan naar voren. UD-Stomp 11 Fig.2 Fig.3 T80:Flat Washer 12x17 0.5 MFNI33 (V7407400) T110:Bind Head Tapping Screw-B 3.0 x8 MFZN2BL (EP600190) T70:Washer 9.0 MFZN2Y (ET800150) T110:Bind Head Tapping Screw-B 3.0 x8 MFZN2BL (EP600190) 3.PN1/2 Circuit Boards (Manhour requirement: 13 min.) 3-1.Remove the bottom case. (See Procedure 1.) 3-2.Remove the DM circuit board. (See Procedure 2.) 3-3.Remove the controls, knobs and the fourteen (14) hexagonal nuts A from the front panel, the three (3) screws marked T110 and the shield film from the PN1/2 circuit board. The PN1/2 circuit board can then be removed. (Fig. 3) 4.PN 2/2 Circuit Board (Manhour requirement: 10 min.) 4-1.Remove the bottom case. (See Procedure 1.) 4-2.Remove the DM circuit boards. (See Procedure 2.) 4-3.Remove the four (4) hexagonal nuts B and the four (4) flat washers marked T80 from foot switches. The PN 2/2 circuit board can then be removed. (Fig. 3) Hexagonal Nut A Hexagonal Nut A Hexagonal Nut B 1/2 T110 T80T80 T110 shield sheet PN 2/2PN Hexagonal Nut B T110B DM Topcover T70 UD-Stomp 12 Fig.4 5.Heat Sink (Manhour requirement: 8 min.) 5-1.Remove the bottom case. (See Procedure 1.) 5-2.Remove the DM circuit board. (See Procedure 2.) A-a A-a A-b IC114 IC113 IC112 Heat Sink 5-3.Remove the two (2) screws marked A-a from the soldered face of the DM circuit board and the three (3) screws marked A-b from IC112, IC113 and IC114. The heat sink can then be removed from the DM circuit board. (Fig. 4) UD-Stomp 13 LSI PIN DESCRIPTION PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 I/O O O I I I I I I I I O O O I I O I I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O O O O O O O O O O O O PA6 PA7 VCC PB0 PB1 PB2 PB3 PB4 PB5 PB6/DREQ0 PB7/DREQ1 /RESO VSS P90/TXD0 P91/TXD1 P92/RXD0 P93/RXD1 P94/SCK0 P95/SCK1 P40/D0 P41/D1 P42/D2 P43/D3 VSS P44/D4 P45/D5 P46/D6 P47/D7 D8 D9 D10 D11 D12 D13 D14 D15 VCC A0 A1 A2 A3 A4 A5 A6 A7 VSS A8 A9 A10 A11 NAME Port A Port A Power supply Port B Reset Ground Port 9 (Ground) Data bus Power supply Address bus (Ground) FUNCTION PIN NO. 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 I/O O O O O O O O O I I I O I I I I O O O O O I I I I I I I I I I I I O O O O O I I I O O O A12 A13 A14 A15 A16 A17 A18 A19 VSS P60/WAIT P61/BREQ P62/BACK /STBY /RES NMI VSS EXTAL XTAL VCC /AS /RD /HWR /LWR MD0 MD1 MD2 AVCC VREF P70/AN0 P71/AN1 P72/AN2 P73/AN3 P74/AN4 P75/AN5 P76/AN6 P77/AN7 AVSS P80 P81/CS3 P82/CS2 P83/CS1 P84/CS0 VSS PA0 PA1 PA2 PA3 PA4 PA5 NAME Address bus Ground Port 6 out, =FAI Stand-by mode signal Reset Non-maskable interrupt Ground Clock Clock Power supply Address strobe Read strobe Write strobe (High) Write strobe (Low) Mode select Analog power supply Reference voltage Port 7 (ANALOG INPUT) Analog ground Port 8 Chip select Ground Port A FUNCTION HD6413002FP16 (XQ375A00) CPUDM: IC12 UD-Stomp 14 PIN NO. I/OFUNCTIONNAME PIN NO. I/OFUNCTIONNAME 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 Vdd Vss XI XO Vdd5 /SYNCI /SYNCO Vdd5 CKI CKO CKSEL Vss MCKS /SSYNC /IC /TEST BTYP /IRQ TRIG Vdd5 Vss /CS /WR /RD CA7 CA6 CA5 CA4 CA3 CA2 CA1 Vss Vdd CD15 CD14 CD13 CD12 CD11 CD10 CD09 CD08 CD07 CD06 Vss Vdd Vdd5 CD05 CD04 CD03 CD02 CD01 CD00 /WAIT Vss SI0 SI1 SI2 SI3 SI4 SI5 SI6 SI7 Vss Vdd5 SO0 SO1 SO2 SO3 SO4 SO5 SO6 SO7 Vss DB00 DB01 DB02 DB03 DB04 DB05 DB06 DB07 DB08 DB09 DB10 DB11 DB12 Vdd5 Vdd I O I O I O I I I I I I O I/O I I I I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O I I I I I I I I O O O O O O O O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O Power supply (3.3 V) Ground System master clock input (60 MHz or 30 MHz) System master clock output (High or 30 MHz) Power supply (5 V) Sync. signal input Sync. signal output Power supply (5 V) System clock input (30 MHz)