ADA-i-series-delay-manual 电路图.pdf

Originally written by ADA SIGNAL PROCESSORS, INC. Scanned and edited by Jur at 1th of may 2004. Original ADA logo edited and rendered by Barend Onneweer of Raamw3rk.) The version of this manual is copyrighted and may not be sold or placed on a website without permission of the editor. Release No.1 for 64i 1.28i 2.56i DIGITAL DELAYS OWNERS MANUAL RadioFans.CN 收音机爱 好者资料库 ADA 64i-1.28i-2.56i owners manual Contents 1.0 INTRODUCTION 1.1 FEATURES 1.2 PRECAUTIONS 2.0 CONTROL FUNCTIONS 2.1 REAR PANEL 3.0 INITIAL SET-UP 3.1 INPUT/OUTPUT ADJUSTMENT 3.2 REMOTE FUNCTIONS 3.3 REGENERATION SECTION 3.4 PHASE 3.5 REPEAT HOLD 3.6 DELAY SECTION 3.7 MODULATION 4.0 PATCH DIAGRAMS FIGURE: 4-1 CLASSIC FLANGE 4-2 EVEN/ODD HARMONIC 4-3 THICK CHORUS 4-4 STEREO DOUBLING 4-5 REPEAT ECHO 4-6 REPEAT HOLD 4-7 REVERB 4-8 STEPPED PITCH-SHIFTING 4.1 BLANK PATCH SHEETS 5.0 SPECIFICATIONS 6.0 BLOCK DIAGRAM Page 2 of 11 RadioFans.CN 收音机爱 好者资料库 ADA 64i-1.28i-2.56i owners manual 1.0 INTRODUCTION Thank you for purchasing one of our professional ADA DIGITAL DELAYS, The .64i, 1,28i, and 2.56i combine the latest in digital technology with innovative, yet cost effective designs. They fulfill your long delay and special effects processing needs with fuli bandwidth at all delay settings, more useful features, and better sound quality than anything else in their respective classes. To properly set-up and familiarize yourself with your new DIGITAL DELAY, read and follow these operating instructions completely. Also, please take this time to fill-out and return your enclosed WARRANTY CARD. 1.1 FEATURES .64i Up to 640ms of delay at 16kHz bandwidth. 1.28i Up to 1280ms of delay at 16kHz bandwidth. 2.56i Up to 2560ms of delay at 16kHz bandwidth. Flanging, chorusing, doubling, slapback, long echos, infinite repeat. LED RATE indicator displays delay time for accurate, real-time echo setting. WAVEFORM control continuously blends the sweep modulation from triangle to sine to square wave. PHASE reversal switch for positive and negative flanging. Remote footswitch control of EFFECT BYPASS and REPEAT HOLD (with optional FS-2 DUAL FOOTSWITCH). MODULATION LEDS give a visual indication of the speed, direction, and position of the sweep as it moves up and down. REGENERATION HI-CUT (EQ) variable between 16kHz to 1.0kHz. 8:1 sweep for flanging and chorusing effects that sweep over a wider range than competing digital delays. 90dB dynamic range. One year parts and labor warranty. 1.2 PRECAUTIONS WARNING: To prevent fire or shock hazard, do not expose this appliance to rain or moisture. CAUTION: To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified service personnel. 2.0 CONTROL FUNCTIONS HEADROOM A 4-step LED meter with a 30dB range which displays signal level relative to clipping level. INPUT LEVEL A boost/attenuate preamp that accepts levels from -10dBV to +20dBV. INPUT IN Engages or bypasses the effect section. (LED indicates Effect is engaged.) OUTPUT MIX Determines the mix between the delay and dry signal. OUTPUT LEVEL Adjusts the EFFECT OUTPUT signal level up to +20dBM. REGENERATION LEVEL Controls the amount of the delayed signal fed back to the input. REGENERATION HI-CUT Reduces the high frequency content in the delayed audio signal that is fed back to the input. Adjustable from 16kHz to 1.0kHz. PHASE Reverses the polarity of the delayed audio signal which is being fed back to the delay line input and to the OUTPUT MIX. REPEAT HOLD Engages the infinite repeat function (remotely controllable). Page 3 of 11 ADA 64i-1.28i-2.56i owners manual LED indicates REPEAT HOLD is engaged. DELAY RATE An LED indicator that blinks at the rate of the delay time interval. DELAY RANGE Interlocking pushbuttons for selection of the delay time range. DELAY MULTIPLIER Allows a continuous 0.125X to 1X adjustment of any selected delay range. MODULATION DEPTH Determines the range of delay time that is swept by the low frequency oscillator. MODULATION LEDS Pair of LEDs indicates the speed, direction, and position of the sweep as it moves up and down. MODULATION SPEED Sets the speed of the low frequency oscillator that sweeps the delay time. Sweep speed varies from 0.1 sec to 25 seconds. MODULATION WAVEFORM Continuously blends the shape of the sweep modulation from a triangle to sine to square wave. TRIANGLE LED Indicates power is ON. 2.1 REAR PANEL FUSE Externally accessible 0.5AMP fuse. Replace with equivalent type and rating only. POWER SWITCH ON/OFF rocker switch (located near power supply to prevent the leakage of AC line hum into the audio circuitry). REMOTE Remote control of EFFECT BYPASS and REPEAT HOLD functions. Used with standard ” stereo cord and-dual footswitch (momentary type). EFFECT OUT A 600 ohm unbalanced output. The level is set with the OUTPUT LEVEL control and carries the mix of dry and delayed signal set by the OUTPUT MIX control. DIRECT OUT A 600 ohm unbalanced output of dry signal only. The level is the same as the input signal level. INPUT An unbalanced high impedance input which interfaces with low or high impedance sources and low and high signal levels. FIGURE 3-1 INITIAL FRONT PANEL SET-UP 3.0 INITIAL SET-UP ADA DIGITALS interface with a wide variety of input sources including high level microphones, electronic instruments and mixing consoles. The INPUT circuitry is high impedance which functions properly with both low or high impedance sources and low (- 10dBV) and high ( + 24dBV) signal levels. (A) To prepare your DIGITAL DELAY for use, set the rear panel POWER SWITCH to the OFF position. Also set your amplifiers power switch to the OFF position. (B) Connect your DIGITAL DELAYS AC CORD to a grounded outlet. (C) Set the front panel controls as shown above (Figure 3-1). ,64i and 2.56i owners should use the longest delay factor pushbutton, 640rns and 2560ms respectively. (D) Connect your signal source to the INPUT jack located on the rear panel. (E) Connect the EFFECT OUTPUT on your DIGITAL DELAY to your amplifier input or mixing console effects receive input. The DIRECT OUTPUT is used with a second amplifier for stereo effects. Page 4 of 11 ADA 64i-1.28i-2.56i owners manual (F) Select the ON position of the rear panel POWER SWITCH (the TRIANGLE LED should now be lit), then set your amplifiers power switch to the ON position. (G) Engage the EFFECT IN pushbutton. Your DIGITAL DELAY is now ready for operation. 3.1 INPUT/OUTPUT ADJUSTMENT (A) The 4-step HEADROOM LED Meter provides accurate monitoring of the input signal level relative to the clipping level. To properly set the input level: find the strongest signal or musical passage that you will put into your DIGITAL DELAY, and set the INPUT LEVEL control to just barely light the red 0dB HEADROOM LED. The LED should flicker only on the strongest signals or notes Never set the INPUT LEVEL control so the 0dB LED is constantly on. Note that the HEADROOM LED Meter monitors, all Signals entering the delay line. The REGENERATION LEVEL control may effect the headroom and therefore the readings. While performing, always remember to monitor the HEADROOM LED Meter for possible overloads. (B) The OUTPUT MIX control mixes the processed signal with the dry input signal. For use with instruments, the control will most often be in its center range. For studio applications where your DIGITAL DELAY is in an effects loop, the MIX control is most useful in the full clockwise, DELAY, position. The processed signal level (and thus the dry/effect mix) is now controlled at the console. (C) The OUTPUT LEVEL control sets the level of the EFFECT OUTPUT whether in bypass or effect IN mode. In general, guitar level signals will have the control in its mid- scale or higher, line level signals will generally require positioning the control more counter-clockwise. Remember, proper setting of the INPUT/OUTPUT LEVEL controls is necessary to achieve maximum performance with the least amount of noise and distortion. 3.2 REMOTE FUNCTIONS EFFECTS BYPASS and REPEAT HOLD are remotely controllable via the rear panel jack labeled REMOTE. The REMOTE jack accepts a standard ” stereo cord (tip-ring-sleeve). The stereo cord connects with two momentary footswitches. In the EFFECT BYPASS mode, the input signal source is routed to the EFFECT OUTPUT. BYPASS is actuated by a momentary closure which grounds the tip to the sleeve. The REPEAT HOLD function allows non-deteriorating repeat of any source stored in the delay memory. REPEAT HOLD is actuated by a momentary closure which grounds the ring to the sleeve. Note that the front panel switches may also be used while the dual footswitch is connected 3.3 REGENERATION SECTION As the REGENERATION LEVEL control is turned clockwise, more of the delayed audio signal is sent back to the input of your DIGITAL DELAY. When using short delay settings, from 0.15 to 40ms, the REGENERATION LEVEL control adds emphasis or resonance to flanging and chorusing. At longer time delays, from 80 to 2560ms the REGENERATION LEVEL control adds repeat echos extending to 50 seconds or more. Room ambience or naturally reflected sounds are quite different from the original signal because reflective surfaces of a room absorb high frequencies more quickly than low frequencies. ADA DIGITALS can simulate room acoustics by rolling-off the higher frequencies with the continuously variable REGENERATION HI-CUT control. At minimum cut (16kHz), the delayed signal is not altered. In the maximum cut position (1.0kHz), all Page 5 of 11 ADA 64i-1.28i-2.56i owners manual regenerated signal content above the mid-range frequencies is attenuated to simulate highly damped room acoustics. The frequency spectrum of the sound source generally decays as it would in a natural environment. 3.4 PHASE The delayed signals phase is inverted when the PHASE pushbutton is engaged. Inverted phase may correct phasing problems in mixing consoles, or alter the tonal characteristics of short delay effects such as resonant flanging and doppler chorusing. 3.5 REPEAT HOLD When engaged, the REPEAT HOLD pushbutton will capture and repeat the signal stored in memory indefinitely without any loss of audio quality. Up to 2560ms (on the 2.561) of a musical passage may be repeated as a counterpoint or a background rhythm. When your DIGITAL DELAY is initially powered up, an internal protection circuit switches the REPEAT HOLD function out to prevent howling. 3.6 DELAY SECTION The DELAY MULTIPLIER control allows continuous 0.125X to 1X adjustment of the delay time selected from any one of the interlocking DELAY range pushbuttons. The ranges of each of the DELAY pushbuttons are as follows: FIGURE 3-2 .64 DELAY TIME RANGES Left to right PUSHBUTTON DELAY TIME (in ms) MIN MAX EFFECT #1 #2 #3 #4 #5 .31 to 2.5 1.25 to 10 5 to 40 20 to 160 80 to 640 Hi Flange Lo Flange Chorus Double/Echo Echo FIGURE 3-4 1.28i DELAY TIME RANGES Left to right PUSHBUTTON DELAY TIME (in ms) MIN MAX EFFECT #1 #2 #3 #4 #5 #6 .15 to 1.25 .62 to 5 2.5 to 20 10 to 80 40 to 320 160 to 1280 Hi Flange Lo Flange Chorus Chorus/Dbl. Double/Echo Echo FIGURE 3-4 2.56i DELAY TIME RANGES Left to right PUSHBUTTON DELAY TIME (in ms) MIN MAX EFFECT #1 #2 #3 #4 #5 #6 .31 to 2.5 1.25 to 10 5 to 40 20 to 160 80 to 640 320 to 2650 Hi Flange Lo Flange Chorus Double/Echo Echo Long Echo Page 6 of 11 ADA 64i-1.28i-2.56i owners manual 3.7 MODULATION The MODULATION DEPTH control allows you to fade between the static setting of the DELAY MULTIPLIER control and the sweeping voltage of the internal low frequency oscillator. When the DEPTH control is set at 0, the delayed signal is not swept and the delay time remains stationary. As the DEPTH control is turned clockwise, a wider range of the selected time delay is swept. With the DEPTH control set at 1 0, the full 8: 1 range is swept and the MULTIPLIER control is disabled. At settings less than 10, the MULTIPLIER sets the center of the sweep range. The MODULATION RATE LEDS give a visual indication of the sweep speed, the direction the sweep is moving (up or down), and how close the sweep is to its upper or lower limits. The RATE LEDS increase in brightness as they reach their upper or lower limits, giving a visual indication of the point where your effect is starting to turn around. The MODULATION WAVEFORM control continuously blends the shape of the modulation function from a triangle to a sine to a square wave. Full counterclockwise position of the knob selects a triangle wave for delay times that reach a peak or dip and quickly turnaround especially useful for flanging effects. Advancing the knob towards the 12 oclock position selects pure sine wave modulation for delay times that smoothly increase and decrease at a speed corresponding to the RATE control, useful for chorusing and vibrato effects. Full clockwise position selects a square wave for delay times that jump up, then down, for stepped pitch-shifting effects. The MODULATION SPEED control adjusts the low frequency oscillator from (Msec to 25sec. Extremely slow sweeps are useful for chorusing, flanging and subtle effects. Faster sweeps can produce vibrato, fast flanging and rotating speaker simulation. 4.0 PATCH DIAGRAMS IMPORTANT NOTICE: .64i OWNERS SHOULD USE DIAGRAMS OF 2.561 TO SET FRONT PANEL CONTROLS, AS THE FIRST FIVE DELAY PUSHBUTTONS ON THE 2.561 ARE IDENTICAL TO THE THOSE ON THE .64 FIGURE 4-1 / CLASSIC FLANGE This demonstrates the full 8:1 sweep range of your digital delay. Turning the REGENERATION LEVEL control clockwise produces more resonant or more dramatic flanging effects. FIGURE 4-2 / EVEN/ODD HARMONIC At minimum MULTIPLIER control settings, switch between in-phase and out-of-phase settings with the PHASE switch. Inverted signals will cancel lower-frequencies thereby apparently emphasizing treble content. Page 7 of 11 ADA 64i-1.28i-2.56i owners manual FIGURE 4-3 / THICK CHORUS This is a dramatic, very deep chorus. Adjust the SPEED control for the desired effect. FIGURE 4-4 / STEREO DOUBLING The OUTPUT MIX control is set at full delay (10) for double tracking when using the DIRECT OUTPUT and the EFFECT OUTPUT in a stereo PA or recording system. In mono systems, set the OUTPUT MIX control in its center position (5). A single short repeat of the note or chord is produced for added thickness. FIGURE 4-5 / REPEAT ECHO By carefully adjusting the REGENERATION LEVEL control, you can select from one repeat to multiple repeats lasting 30 seconds or more. Vary the HI-CUT control to further modify the repeat echo by taking the edge off of percussive signals. Page 8 of 11 ADA 64i-1.28i-2.56i owners manual FIGURE 4-6 /REPEAT HOLD This captures, stores, and repeats a segment of sound without signal degradation. The pitch and repeat rate may be modified by