Qsc - Mx7001 SS 电路图.pdf

MX 700 FEATURES A U D I O 1675 MacArthur Boulevard Costa Mesa, California 92626-1468 USA Phone: 714/754-6175 Fax: 714/754-6174 MX Series LOADFTC CONTINUOUS AVERAGEEIA WATTS 20Hz-20kHz, 0.1% THD1kHz, 1% THD Stereo (W/Ch) 8150 watts170 watts 4225 watts270 watts 2350 watts* Mono-Bridged 16300 watts340 watts 8450 watts540 watts 4700 watts* *typical 350 watts per channel at 2 ohms 270 watts per channel at 4 ohms Only 12 deepfits shallow racks Low profileOnly 2 rack spaces high LightweightOnly 25 lbs. Two-speed fan for quiet operation Direct mounted power transistors for better thermal performance Recessed front panel controls for easy access and protection from damage 1/4 and barrier strip input connectors Touch proof binding post output connectors Clipping indicators THX approved for cinema applications 3 year warranty PLUS optional 3 year extended service contract he MX 700 has been designed to combine QSCs legendary reliability and sonic quality into a low cost/high performance package. The com- pact size of the MX 700 makes it perfect for working musicians who dont want to carry bulky amplifiers, but still demand high power. It is also ideal for powering mid range drivers and tweeters in large sound systems. The MX 700 provides 170 watts per channel into 8 ohms, 270 into 4 ohms, and 350 into 2 ohm loads. The MX 700 uses 2-speed fan cooling to mini- mize operating temperatures and fan noise. Front panel gain controls and clip indicators make operational settings simple and straight- forward. Rear panel input and output connec- tors allow for easy interface to outboard equip- ment. QSC is a pioneer in premium quality, high power, low profile amplifiers with thousands of units installed in touring systems and concert halls worldwide. The MX 700 puts QSCs proven tech- nology to work in a very economical package. The result is proven reliability at a new level of value. TUV PRODUCT? SERVICE geprfte? Sicherheit . R RadioFans.CN 收音机爱 好者资料库 ARCHITECTS AND ENGINEERS SPECIFICATIONS The amplifier shall contain all solid-state circuitry, using complementary silicon output devices. The amplifier shall operate from 50-60 Hz AC power, with internal taps for selecting voltages 100,120, or 220-240 Vac. The amplifier shall operate from a normal household AC outlet, drawing less than 444 VA when driven with random program material at 1/8 rated power into four ohm loads. The amplifier shall be supplied with a single molded AC cord having an appropriate AC plug for the intended operating volt- age. The amplifier shall employ forced-air cooling with a two speed fan for minimum acoustic noise. Air flow shall be from rear to front to avoid tem- perature rise inside the rack. Rack mounting shall be possible without clearance necessary between amplifiers for ventilation. The amplifier shall be capable of continuous operation at 1/8 power, into four-ohm loads, for ambient temperatures up to 104 F (40 C). The amplifier shall contain two independent channels, with separate AC transformer secondaries, power supplies, and protection systems. All pro- tection systems shall be self resetting upon removal of fault, and the re- maining channel shall continue to operate. Each channel shall have inde- pendent protective circuitry against open circuit, short circuit, or mis- matched loads. Each channel shall monitor temperature of its heat sink, and shall trigger fan speed boost, and if necessary, signal muting to pre- vent excessive temperature rise. Each channel shall have on-off muting, acting for two seconds after turn-on, and within 1/4 second after turn-off or loss of AC power. Each channel shall have DC fault protection for the load. Fault fuses shall be adequately large to prevent nuisance blowing at any output power the amplifier is capable of delivering. Each channel shall have the following controls and displays: A front panel Gain control and a red LED showing true amplifier clipping. The front panel shall also include a power switch and green LED power-on indicator. The output connectors for each channel shall include a touch proof bind- ing post. The input connectors shall be mounted on the rear panel and shall provide barrier strip and 1/4 connections for each channel. Inputs shall be elec- tronically balanced, with a minimum impedance of 10 kilohms per side, and a common mode rejection of at least 50 dB from 20 Hz to 20 kHz. Each channel shall be capable of meeting the following performance cri- teria with both channels driven: Sine-wave output power of 150 watts into eight ohms, and 225 watts into four ohms, 20Hz to 20kHz, with less than O.1% THD. Frequency response at 3dB below rated power shall be 20Hz to 20kHz within O.15 dB. The voltage gain shall be 35, equivalent to 31dB, and the input sensitivity shall be .96 Vrms. The signal to noise ratio over the range of 20 Hz to 20 kHz shall exceed 100 dB, A weighted. IHF damping factor shall exceed 200. The amplifier chassis shall occupy two rack spaces, with provision for securing the rear corners. Depth from mounting surface to tips of rear supports shall be 12.0 (30.5 cm). Weight shall not exceed 25 Ibs. (11.3 kg.). The amplifier shall be the QSC Audio Products Model MX 700. BACK MX 700 Specifications A U D I O 1675 MacArthur Boulevard Costa Mesa, California 92626-1468 USA Phone: 714/754-6175 Fax: 714/754-6174 OUTPUT POWER (per channel) 8 ohms, 20 Hz to 20 kHz, 0.1%THD, 150 watts 8 ohms, 1kHz,1%THD, 170 watts 4 ohms, 20 Hz to 20 kHz, 0.1%THD, 225 watts 4 ohms, 1 kHz,1%THD, 270 watts 2 ohms, 1 kHz,1%THD, 350 watts* OUTPUT POWER (bridged mono) 8 ohms, 20 Hz to 20 kHz, 0.1%THD, 450 watts 4 ohms, 1 kHz,1%THD 700 watts* *typical DISTORTION: SMPTE-IM, less than 0.025% THD 20Hz-20kHz less than 0.1% 0.01% typical FREQUENCY RESPONSE: 20 Hz to 20 kHz, +0/-1 dB 8 Hz to 100 kHz, +0/-3 dB DAMPING FACTOR: Greater than 200 DYNAMIC HEADROOM: 3 dB at 4 ohms NOISE: 100 dB below rated output (A weighted) SENSITIVITY: 0.96 Vrms for rated power (8 ohms) VOLTAGE GAIN: 35 (31 dB) INPUT IMPEDANCE: 10K unbalanced, 20K balanced CONTROLS: Front: AC Switch, Ch 1 and Ch 2 Gain Knobs INDICATORS: PWR-ON:Green LED CLIP:Red LED CONNECTORS: (each channel) Input:Barrier strip and 1/4 RTS Speakers: Touch proof binding posts COOLING: Two-speed fan, rear-to-front air flow. AMPLIFIER PROTECTION: Full short circuit, open circuit, ultrasonic, and RF protection. Stable into reactive or mismatched loads. LOAD PROTECTION: AC coupled output. 2-second turn on and instant off muting OUTPUT CIRCUIT TYPE: Complementary linear outputs, grounded collector, class A/B POWER REQUIREMENTS: 100,120, 240 Vac, 50-60 Hz POWER CONSUMPTION: Normal Operation: 4 ohms per channel: 3.7 amps, 120 Vac (444VA). Maximum (full power, 2 ohms per channel): 14.6 amps, 120 Vac (1752 VA) DIMENSIONS: 19.0 (48.3 cm) rack mounting 3.5 (8.9 cm) tall (2 spaces) 12.0 (30.5 cm) deep (rear support ears) WEIGHT: 25 Ibs (11.3 kg) net, 33 Ibs (15.0 kg) shipping Output Averaging short circuit protection (US Patent 4,321,554) SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE. RadioFans.CN 收音机爱 好者资料库