Aiwa-XRMDK505-cs-sm 电路图 维修手册.pdf

SERVICE MANUAL DATA MD/CD STEREO SYSTEM XR-MDK505 S/M Code No. 09-00A-351-2N1 HRJ(S) BASIC TAPE MECHANISM : 2ZM-1 R11NM BASIC CD MECHANISM : 3ZG-3 E3NM BASIC MD MECHANISM : AZG-4 YA SYSTEM SPEAKERREMOTE CONTROL XR-MDK505SX-M510 YRC-AAT18 If requiring information about the MD mechanism, see Service Manual of AZG-4YA, (S/M Code No.09-001-341-2N2). RadioFans.CN 收音机爱 好者资料库 -2- TABLE OF CONTENTS SPECIFICATIONS.2 ACCESSORIES LIST .4 PROTECTION OF EYES FROM LASER BEAM DURING SERVING .5 DISASSEMBLY INSTRUCTIONS .6 9 SERVICE JIG AND TOOLS.10 NOTES DURING RE-ASSEMBLING . 11 CD TEST MODE .12 MD TEST MODE .13 26 ELECTRICAL MAIN PARTS LIST .27 33 TRANSISTOR ILLUSTRATION.34 SCHEMATIC DIAGRAM - 1 (MAIN SECTION) .35 SCHEMATIC DIAGRAM - 2 (FRONT SECTION).38 SCHEMATIC DIAGRAM - 3 (VCD - 1/2 SECTION) .41 SCHEMATIC DIAGRAM - 4 (VCD - 2/2 SECTION) .42 SCHEMATIC DIAGRAM - 5 (TUNER SECTION).45 WIRING - 1 (MAIN C.B) .36 WIRING - 2 (PT 1, 2 C.B) .37 WIRING - 3 (FRONT, SWITCH-1,2 C.B) .39 WIRING - 4 (FACE-A, B, C C.B) .40 WIRING - 5 (VCD, VIDEO OUT, CD LOAD,CD DRIVE C.B) .43 WIRING - 6 (DECK, RELAY C.B) .44 WIRING - 7 (TUNER C.B) .46 IC BLOCK DIAGRAM .47 51 IC DESCRIPTION .52 66 FL DISPLAY .67 68 ADJUSTMENT(TUNER/DECK/MAIN) .69 71 MECHANICAL EXPLODED VIEW 1/1 .72 MECHANICAL MAIN PARTS LIST 1/1.73 COLOR NAME LIST.74 TAPE MECHANISM EXPLODED VIEW 1/1 .75 TAPE MECHANISM PARTS LIST 1/1 .76 CD MECHANISM EXPLODED VIEW 1/2 .77 CD MECHANISM PARTS LIST 1/2 .78 CD MECHANISM EXPLODED VIEW 2/2 .79 CD MECHANISM PARTS LIST 2/2 .79 SPEAKER DISASSEMBLY INSTRUCTIONS .80 SPEKAER PARTS LIST .81 RadioFans.CN 收音机爱 好者资料库 -3- SPECIFICATIONS Design and specifications are subject to change without notice. The word “BBE” and the “BBE symbol” are trademarks of BBE Sound, Inc. Under license from BBE Sound, Inc. Dolby noise reduction manufactured under license from Dolby Labo- ratories Licensing Corporation. “DOLBY”, and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. RadioFans.CN 收音机爱 好者资料库 -4- REF. NOPART NO.KANRIDESCRIPTION NO. ACCESSORIES LIST 1 8A-CB4-901-010 IB,H(EC)M 2 8A-CB4-951-010 RC UNIT,RC-AAT18 3 87-006-225-010 AM LOOP ANT NC2 4 87-043-115-010 ANT,FEEDER FM 5 87-050-103-010 CORD,PIN 1PY1.5M 6 87-A91-017-010 PLUG,CONVERSION JT-0476 -5- PROTECTION OF EYES FROM LASER BEAM DURING SERVICING CLASS 1LASER PRODUCT KLASSE 1LASER PRODUKT LUOKAN 1LASER LAITE KLASS 1LASER APPARAT This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing. WARNING! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJEC- TIVE LENS ON THE OPTICAL PICK-UP BLOCK. VAROITUS! VARNING! CAUTION Use of controls or adjustments or performance of proce- dures other than those specified herin may result in hazardous radiation exposure. ATTENTION ADVARSEL This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior. (KSS-213F, KMS-260B) Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode. 1) After the connection, remove solder shown in the figure below. MD PICK-UP Assy P.W.B (KMS-260B) CD PICK-UP Assy P.W.B (KSS-213F) Solder VEE TRK- Pattern Solder Precaution to replace Optical block 1 21 -6- 2) Remove the six screws ( 1 -4, 2 -2) and remove the PANEL, SIDE L. PANEL, SIDE R PANEL, SIDE L PANEL, TOP ASSY 1 111 2 2 1 111 2 2 1 1 1 2 DISASSEMBLY INSTRUCTION -1/4 3) Remove the three screw 1 and lift up the PANEL, TOP ASSY 2 . 4) Remove the two connectors and remove the PANEL, TOP ASSY. 1. Removing the outside appearance parts 1) Remove the six screws ( 1 -4, 2 -2) and remove the PANEL, SIDE R. -7- DISASSEMBLY INSTRUCTION -2/4 6) This is the state after the outside appearance parts are removed. PWB, CD ACB-4 PWB, MAIN ASSY CABI, REAR 2 1 3 5) Remove the 12 screws and remove the CABI, REAR. Remove the connector from FAN from MAIN C.B. 2. Removing the PWB, CD ACB-4 1) Remove the five screws, pull out the FFC and other parts, then remove the PWB, CD ACB-4. The one screw is behind the shield paper. 3. Removing the PWB, MAIN ASSY 1) Remove the screw 1 , then remove the connector 2 and the FFC 3 of the MD block. -8- 2) Remove the screw 1 and remove the PWB, MAIN ASSY in the direction of the arrow 2 . (The board is hooked.While lifting up the HOOK, remove the board.) CHAS,MD CHAS,MD HOOK 1 2 2 1 1 2 CABI, FR ASSY 1 1 2 PWB,MAIN ASSY DISASSEMBLY INSTRUCTION -3/4 4. Removing the FRONT block 1) Remove the screw 1 securing the CAB, FR ASSY and remove the screw 2 securing the CHAS, MD. 2) Remove the screw 1 securing the CAB, FR ASSY and remove the screw 2 securing the CHAS, MD. 3) Remove the two screws 1 and remove the CABI, FR ASSY in the direction of arrow 2 . -9- AZG-4 3ZG-3 2 1 11 1 3ZG-3 DISASSEMBLY INSTRUCTION -4/4 4) This is the state after the PWB, MAIN ASSY and CABI, FRONT ASSY are removed. 5. Removing the MD block (AZG-4) 1) Remove the four screws and remove the MD block. 6. Removing the CD block (3ZG-3) 1) Remove the four screws 1 and remove the CD block 2 . 2) This is the state after the CD block is removed. -10- SERVICE JIG AND TOOLS Using the FFC for extension enables the CD/MD mechanism to be repaired when the power supply is turned on. (Refer to the below figure.) 1 FFC, 8P-1.25 88-908-401-110 2 FFC, 8P-1.0 SV-J00-043-010 3 FFC, 14P-1.0 SV-J00-044-010 MDCD 2 1 3 -11- NOTES DURING RE-ASSEMBLING When assemble the magical change panel, adjust the phase of the gear. 1. Phase adjustment of the GEAR, OPE 1 and GEAR, WORM WHEEL. 1) Align holes 1 . 2) Then, move the position of the holes of each gear as shown by 2 in the illustration. 2. Installation Procedure of HLDR, GEAR ASSY 1) Position the panel side so that it faces front as shown in the illustration. 2) Install the HLDR, GEAR ASSY. GEAR,WORM WHEEL HLDR,GEAR HLDR,GEAR ASSY Position the HLDR GEAR ASSY so that it faces the front. GEAR,OPE 1 -12- CD TEST MODE 1. How to Active CD Test Mode While pressing the CD function button, insert the AC plug to the outlet. When the test mode starts, all indicators in the display will light. 2. How to Cancel CD Test Mode Press other function button or power button, or disconnect the AC plug. 3. CD Test Mode functions NoMODEOperationOperationChecking itemFL display 1 3 2 4 5CD CD TEST (00 00 00) 4. Overview of Operation The each mode can be operated one after another using each button in the order that is shown by arrow mark in the illustration from the Start mode. FL item Microprocessor APC circuit Laser current Focus search waveform Focus error waveform (FOK and FZC are not monitored inthe search mode) Focus servo Tracking servo Sled servo Spindle servo FOK RF waveform Tracking servo Traverse waveform Sled circuit Mechanism Turning off/on repeats each time tracking servo OFF/ON is pressed Normal playback If TOC cannot be read, focus search of 2 is continued Pickup moves to the outermost track *3 Pickup moves to the innermost track (normal) Normal time display Sled mode Traverse mode Search mode Play mode Start modeAll light LD lights Continuous focus search *1 *2 Normal time display (spectrum analyzer) * Note 1: The driver IC (IC501) heats up and the protection circuit starts working when the focus search is continued for 10 minutes or longer. There can be a case that operations cannot be preformed correctly. In such a case, turn off the main power. After cooling down, restart the unit. * Note 2: When checking the lens operation by eye, slightly open the CD cover by hand: The search mode will be released if the CD cover is opened by pressing the OPEN button. Search mode Start mode All display lights Play mode Traverse mode -13- MD TEST MODE - 1/14 OPERATION PANEL PULLEY PWB, CD The test mode has the following contents: 1. Starting MD Test Mode 2. Checking MD Test Mode and Audio Output 3. Releasing MD Test Mode 4. Switching to Servo Standby Mode 5. Checking Sled Feed Operation 6. Checking Laser Power 7. Checking Loading Mechanism Operation and Detection Switch 8. Checking Servo Operation 8-1 Checking focus search/spindle kick 1 8-2 Checking focus search/spindle kick 2 (checking S-curve) 8-3 Checking focus servo and sled error (EF balance) 8-4 Checking all servo on 9. Checking Address and Error Rate 10. Erasing U-TOC (User TOC) 1. Starting MD Test Mode While holding down the “MD” function key, plug the power cord into AC outlet. Cautions: 1)While the test mode is started, the abnormality in mechanism is ignored and operation is performed: If any abnormality is detected in operation, immediately unplug the power cord. 2)During test mode, normal playback or recording is not possible. Key Operation in Test Mode and MD Electrical Adjustment: After the test mode has started, the operation panel will not turn. Perform key operation using either of the following procedures: Key operation on remote control Turn the pulley on PWB, CD so that key operation on MD EDIT STAGE on the operation panel is possible. (See the figure below) -14- 2. Checking MD Test Mode and Audio Output 1) After the test mode has started, the display will be as follows, and the test mode can be used. 2) Checking audio output A 1kHz, -17dB (140mV) signal is output from the MD mechanism output (D/A OUT). The speaker output level is determined by the sound volume before the test mode has started. 3. Releasing MD Test Mode 1) Press the MD EJECT key to remove the disc. 2) Unplug the power cord from the AC outlet. * If the test mode is released using the procedure other than above, the operation may not be normal when power is turned on again. In this case, unplug the power cord. 4. Switching to