Jvc-KWXR-810-J-Service-Manual(1) 电路图 维修手册.pdf

SERVICE MANUAL COPYRIGHT 2010 Victor Company of Japan, Limited No.MA475 2010/3 CD RECEIVER MA47520103 SERVICE MANUAL KW-XR810J, KW-XR816U, KW-XR816UH, KW-XR811E, KW-XR811EY, KW-XR811EU, KW-XR817EE COPYRIGHT 2010 Victor Company of Japan, Limited Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade) Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade) TABLE OF CONTENTS 1PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 2SPECIFIC SERVICE INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9 3DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9 4ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-21 5TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-24 except KW-XR817 only KW-XR810 For KW-XR811/XR817 RadioFans.CN 收音机爱 好者资料库 1-2 (No.MA475) SPECIFICATION Designs & specifications are subject to change without notice. KW-XR810 AUDIO AMPLIFIER SECTION Power Output20 W RMS 4 Channels at 4 and < 1% THD+N Signal-to-Noise Ratio80 dBA (reference: 1 W into 4 ) Load Impedance4 (4 to 8 allowance) Tone Control RangeBass12 dB (50 Hz, 100 Hz, 200 Hz) Q0.7, Q1.0, Q1.4, Q2.0 Middle12 dB (0.5 kHz, 1.0 kHz, 2.0 kHz) Q0.7, Q1.0, Q1.4, Q2.0 Treble12 dB (5.0 kHz, 10.0 kHz, 15.0 kHz) Q0.7, Q1.0, Q1.4, Q2.0 Frequency Response40 Hz to 20 000 Hz Line-Out Level/Impedance2.5 V/20 k load (full scale) Subwoofer-Out Level/Impedance2.5 V/20 k load (full scale) Output Impedance1 k Other TerminalAUX (auxiliary) input jack, USB input terminal, USB cable, Antenna input, Expansion port, Steering wheel remote input TUNER SECTION Frequency RangeFMwith channel interval set to 100 kHz or 200 kHz with channel interval set to 50 kHz AMwith channel interval set to 10 kHz with channel interval set to 9 kHz FM TunerUsable Sensitivity9.3 dBf (0.8 V/75 ) 50 dB Quieting Sensitivity16.3 dBf (1.8 V/75 ) Alternate Channel Selectivity (400 kHz)65 dB Frequency Response40 Hz to 15 000 Hz Stereo Separation40 dB AM TunerSensitivity20 V Selectivity40 dB CD PLAYER SECTION TypeCompact disc player Signal Detection SystemNon-contact optical pickup (semiconductor laser) Number of Channels2 channels (stereo) Frequency Response5 Hz to 20 000 Hz Dynamic Range96 dB Signal-to-Noise Ratio98 dB Wow and FlutterLess than measurable limit MP3 Decoding Format: (MPEG1/2 Audio Layer 3)Max. Bit Rate: 320 kbps WMA (Windows Media Audio) Decoding FormatMax. Bit Rate: 320 kbps USB SECTION USB StandardUSB 1.1, USB 2.0 Data Transfer RateFull SpeedMax. 12 Mbps Low SpeedMax. 1.5 Mbps Compatible DeviceMass storage class (except HDD) Compatible File SystemFAT 32/16/12 Playable Audio FormatMP3/WMA/WAV Max. CurrentDC 5 V 500 mA BLUETOOTH VersionBluetooth 2.0 certified Power ClassClass 2 Radio (possible distance 10 m) Service Area10 m ProfileHFP 1.5, OPP 1.1, A2DP 1.2, AVRCP 1.3, PBAP 1.0 Max. CurrentDC 5 V 54.3 mA GENERAL Power RequirementOperating Voltage DC 14.4 V (11 V to 16 V allowance) Grounding SystemNegative ground Allowable Operating Temperature0C to +40C (32F to 104F) Dimensions (W H D) (approx.) Installation Size182 mm 111 mm 160 mm (7-3/16” 4-3/8” 6-5/16”) Panel Size188 mm 117 mm 23 mm (7-7/16” 4-5/8” 5/16”) Mass1.9 kg (4.2 lbs) (excluding accessories) RadioFans.CN 收音机爱 好者资料库 (No.MA475)1-3 Designs & specifications are subject to change without notice. KW-XR811, KW-XR817 AUDIO AMPLIFIER SECTION Maximum Power OutputFront/Rear50 W per channel Continuous Power Out- put (RMS) Front/Rear20 W per channel into 4 , 40 Hz to 20 000 Hz at no more than 1% total harmonic distortion. Load Impedance4 (4 to 8 allowance) Tone Control RangeBass12 dB (50 Hz, 100 Hz, 200 Hz) Q0.7, Q1.0, Q1.4, Q2.0 Middle12 dB (0.5 kHz, 1.0 kHz, 2.0 kHz) Q0.7, Q1.0, Q1.4, Q2.0 Treble12 dB (5.0 kHz, 10.0 kHz, 15.0 kHz) Q0.7, Q1.0, Q1.4, Q2.0 Frequency Response40 Hz to 20 000 Hz Signal-to-Noise Ratio70 dB Line-Out Level/Impedance2.5 V/20 k load (full scale) Subwoofer-Out Level/Impedance2.5 V/20 k load (full scale) Output Impedance1 k Other TerminalAUX (auxiliary) input jack, USB input terminal, USB cable, Aerial input, Steering wheel remote input(KW-XR811) TUNER SECTION Frequency RangeFM87.5 MHz to 108.0 MHz FM-LOW (KW-XR817)65.0 MHz to 74.0 MHz AMMW: 522 kHz to 1 620 kHz LW: 144 kHz to 279 kHz FM TunerUsable Sensitivity9.3 dBf (0.8 V/75 ) 50 dB Quieting Sensitivity16.3 dBf (1.8 V/75 ) Alternate Channel Selectivity (400 kHz)65 dB Frequency Response40 Hz to 15 000 Hz Stereo Separation40 dB MW TunerSensitivity20 V AM TunerSelectivity40 dB Sensitivity50 V CD PLAYER SECTION TypeCompact disc player Signal Detection SystemNon-contact optical pickup (semiconductor laser) Number of Channels2 channels (stereo) Frequency Response5 Hz to 20 000 Hz Dynamic Range96 dB Signal-to-Noise Ratio98 dB Wow and FlutterLess than measurable limit MP3 Decoding Format: (MPEG1/2 Audio Layer 3)Max. Bit Rate: 320 kbps WMA (Windows Media Audio) Decoding FormatMax. Bit Rate: 320 kbps USB SECTION USB StandardUSB 1.1, USB 2.0 Data Transfer RateFull SpeedMax. 12 Mbps Low SpeedMax. 1.5 Mbps Compatible DeviceMass storage class (except HDD) Compatible File SystemFAT 32/16/12 Playable Audio FormatMP3/WMA/WAV Max. CurrentDC 5 V 500 mA BLUETOOTH VersionBluetooth 2.0 certified Power ClassClass 2 Radio (possible distance 10 m) Service Area10 m ProfileHFP 1.5, OPP 1.1, A2DP 1.2, AVRCP 1.3, PBAP 1.0 Max. CurrentDC 5 V 54.3 mA GENERAL Power RequirementOperating Voltage DC 14.4 V (11 V to 16 V allowance) Grounding SystemNegative ground Allowable Operating Temperature0C to +40C Dimensions (W H D): (approx.) Installation Size182 mm 111 mm 160 mm Panel Size188 mm 117 mm 23 mm Mass1.9 kg (excluding accessories) RadioFans.CN 收音机爱 好者资料库 1-4 (No.MA475) Designs & specifications are subject to change without notice. KW-XR816 AUDIO AMPLIFIER SECTION Maximum Power OutputFront/Rear50 W per channel Continuous Power Out- put (RMS) Front/Rear20 W per channel into 4 , 40 Hz to 20 000 Hz at no more than 1% total harmonic distortion. Load Impedance4 (4 to 8 allowance) Tone Control RangeBass12 dB (50 Hz, 100 Hz, 200 Hz) Q0.7, Q1.0, Q1.4, Q2.0 Middle12 dB (0.5 kHz, 1.0 kHz, 2.0 kHz) Q0.7, Q1.0, Q1.4, Q2.0 Treble12 dB (5.0 kHz, 10.0 kHz, 15.0 kHz) Q0.7, Q1.0, Q1.4, Q2.0 Frequency Response40 Hz to 20 000 Hz Signal-to-Noise Ratio70 dB Line-Out Level/Impedance5.0 V/20 k load (full scale) Subwoofer-Out Level/Impedance5.0 V/20 k load (full scale) Output Impedance1 k Other TerminalAUX (auxiliary) input jack, USB input terminal, USB rear cable, Antenna input, Steer- ing wheel remote input TUNER SECTION Frequency RangeFM87.5 MHz to 108.0 MHz AMMW: 522 kHz to 1 620 kHz LW: 144 kHz to 279 kHz FM TunerUsable Sensitivity9.3 dBf (0.8 V/75 ) 50 dB Quieting Sensitivity16.3 dBf (1.8 V/75 ) Alternate Channel Selectivity (400 kHz)65 dB Frequency Response40 Hz to 15 000 Hz Stereo Separation40 dB AM TunerSensitivity20 V Selectivity40 dB CD PLAYER SECTION TypeCompact disc player Signal Detection SystemNon-contact optical pickup (semiconductor laser) Number of Channels2 channels (stereo) Frequency Response5 Hz to 20 000 Hz Dynamic Range96 dB Signal-to-Noise Ratio98 dB Wow and FlutterLess than measurable limit MP3 Decoding Format: (MPEG1/2 Audio Layer 3)Max. Bit Rate: 320 kbps WMA (Windows Media Audio) Decoding FormatMax. Bit Rate: 320 kbps USB SECTION USB StandardUSB 1.1, USB 2.0 Data Transfer RateFull SpeedMax. 12 Mbps Low SpeedMax. 1.5 Mbps Compatible DeviceMass storage class (except HDD) Compatible File SystemFAT 32/16/12 Playable Audio FormatMP3/WMA/WAV Max. CurrentDC 5 V 500 mA BLUETOOTH VersionBluetooth 2.0 certified Power ClassClass 2 Radio (possible distance 10 m) Service Area10 m ProfileHFP 1.5, OPP 1.1, A2DP 1.2, AVRCP 1.3, PBAP 1.0 Max. CurrentDC 5 V 54.3 mA GENERAL Power RequirementOperating Voltage DC 14.4 V (11 V to 16 V allowance) Grounding SystemNegative ground Allowable Operating Temperature0C to +40C Dimensions (W H D): (approx.) Installation Size182 mm 111 mm 160 mm Panel Size188 mm 117 mm 23 mm Mass1.6 kg (excluding accessories) (No.MA475)1-5 SECTION 1 PRECAUTION 1.1Safety Precautions (1) This design of this product contains special hardware and many circuits and components specially for safety purpos- es. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Services should be per- formed by qualified personnel only. (2) Alterations of the design or circuitry of the product should not be made. Any design alterations of the product should not be made. Any design alterations or additions will void the manufacturers warranty and will further relieve the manufacture of responsibility for personal injury or property damage resulting therefrom. (3) Many electrical and mechanical parts in the products have special safety-related characteristics. These characteris- tics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by us- ing replacement components rated for higher voltage, watt- age, etc. Replacement parts which have these special safety characteristics are identified in the Parts List of Ser- vice Manual. Electrical components having such features are identified by shading on the schematics and by ( ) on the Parts List in the Service Manual. The use of a substitute replacement which does not have the same safety charac- teristics as the recommended replacement parts shown in the Parts List of Service Manual may create shock, fire, or other hazards. (4) The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/or sharp edges for the prevention of electric shock and fire hazard. When service is required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to normal, after reassem- bling. (5) Leakage shock hazard testing After reassembling the product, always perform an isola- tion check on the exposed metal parts of the product (an- tenna terminals, knobs, metal cabinet, screw heads, headphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock.Do not use a line isolation transformer during this check. Plug the AC line cord directly into the AC outlet. Using a Leakage Current Tester, measure the leakage current from each exposed metal parts of the cabinet, particular- ly any exposed metal part having a return path to the chassis, to a known good earth ground. Any leakage cur- rent must not exceed 0.5mA AC (r.m.s.). Alternate check method Plug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 per volt or more sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15F AC-type capacitor between an ex- posed metal part and a known good earth ground. Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each exposed metal part, particularly any exposed metal part having a return path to the chassis, and measure the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. Voltage measured any must not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5 mA AC (r.m.s.). 1.2Warning (1) This equipment has been designed and manufactured to meet international safety standards. (2) It is the legal responsibility of the repairer to ensure that these safety standards are maintained. (3) Repairs must be made in accordance with the relevant safety standards. (4) It is essential that safety critical components are replaced by approved parts. (5) If mains voltage selector is provided, check setting for local voltage. 1.3Caution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of pre- forming repair of this system. 1.4Critical parts for safety In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the mark nearby are critical for safety. When replacing them, be sure to use the parts of the same type and rating as specified by the manufacturer. (This regulation dose not Except the J and C version) Good earth ground Place this probe on each exposed metal part. AC VOLTMETER (Having 1000 ohms/volts, or more sensitivity) 1500 10W 0.15 F AC TYPE 1-6 (No.MA475) 1.5Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.5.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products. Be careful to use proper grounding in the area where repairs are being performed. (1) Ground the workbench Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the traverse unit (optical pickup) on it. (2) Ground yourself Use an anti-static wrist strap to release any static electricity built up in your body. (3) Handling the optical pickup In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.) Do not use a tester to check the condition of the laser diode in the optical pickup. The testers internal power source can easily destroy the laser diode. 1.6Handling the traverse unit (optical pickup) (1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. (2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a time when attaching it to the connector. (3) Handle the flexible cable carefully as it may break when subjected to strong force. (4) I t is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it. 1M Con