Kenwood-DNX-5220-BT-Service-Manual 电路图 维修手册.pdf

This product uses Lead Free solder. This product complies with the RoHS directive for the European market. 2008-2 PRINTED IN JA PAN B53-0620-10 (N) 519 MONITOR WITH DVD RECEIVER DDX5022/5022Y/5032 /5032M/512/52RY DNX5120/512EX/5220/5220BT SERVICE MANUAL * Depends on the models. Refer to the parts list. Remote controller * (A70-2083-15) Size AAA battery Not supplied RC-DV340 Escutcheon (B07-3165-02) Mounting hardware assy (J22-0657-03) Lever (D10-4589-04) x2 Escutcheon * (B07-3172-12) DC cord * (E30-6796-05) DC cord * (E30-6795-05) Cord with plug * (E30-6785-05) Screw set * (N99-1779-15) Adhesive double- coated tape * (H30-0595-04) Antenna module(GPS-ANT) (W02-5305-05) Mounting hardware * (J21-9867-04) Panel assy (A64-4530-11): DDX512 (A64-4532-11): DDX5022/5022Y (A64-4535-11): DNX5120 (A64-4536-11): DNX5220BT (A64-4537-11): DNX5220 (A64-4539-01): DDX5032/5032M (A64-4540-01): DDX52RY (A64-4551-01): DNX512EX Illustrations is DNX5220BT Except K,R type Only DNX Only DNX5220BT The IC3, and IC11 in the DVD unit (X37-1100-03) are not replaceable components. When these ICs are defective, replace the whole DVD mechanism assembly (X92-6160-00). You cannot replace only the board. Microphone * (W01-1718-05) RadioFans.CN 收音机爱 好者资料库 2 DDX5022/5022Y/5032/5032M/512/52RY DNX5120/512EX/5220/5220BT In assembling the Traverse UD arm, Drive cam assembly, Drive gear 5 and Drive gear 4C, align register marks on these components. GEAR POSITION IN A DVD MECHANISM BLOCK DIAGRAM Drive gear 5 Drive cam assembly Do not forcibly press gears to engage their teeth but freely let the gears fall under their own weight and engage their teeth. Traverse UD arm Drive gear 4C Inscriptions (register marks) on gears Align 6 marks as shown in the figure DVS-8000V BLOCK DIAGRAM (X37-1100) SPINDLE MOTOR DISC OPTICAL PICKUP STEPPING 2 PHASE CN1 30PIN 28PIN CN3 MOTOR “GraphicNAVI”. Graphic and NAVI of DNX are used in the adjustment of Dot FREQ/Phase. The Adjustment screen is shown in Figure 3.9. Cancel Return HPOSI AdjustHPOSI Adjust ? HPOSI OK/NG Next << << < Step value Step value Step value Graphic (NAVI) HPOSI Dot FREQ Dot Phase Figure 3.9 HPOSI screen Key Specifi cation Next : Transfer to the next HPOSI Adjustment screen. When the screen is NAVI, the screen starts writing in the E2PROM. < : Screen toward the right. Cancel : Transfer to Test Mode Main screen Return : Transfer to Test Mode Main screen If HPOSI NG (E2PROM Write NG) is shown, transfer to the Test Mode again to start over the adjustment. 3.10 iPod screen Check communication for iPod authentication. The iPod screen is shown in Figure 3.10. CancelReturn iPod CheckiPod Check ? iPod OK/NGiPod Check Figure 3.10 iPod screen Key Specifi cation iPod Check : Start checking communication for iPod authentication. Cancel, Return : Transfer to Test Mode Main screen 20 DDX5022/5022Y/5032/5032M/512/52RY DNX5120/512EX/5220/5220BT TEST MODE 3.11 Auto Adjust screen Carry out the automatic adjustment of Chroma / Mstar. The contents displayed on the Auto Adjust screen are shown in Figure 3.11. Note: Refer to the hardware service documents for the equipment to connect to the set. CancelReturn Auto AdjustAuto Adjust ? Adjust OK/NG Auto Adjust Start Figure 3.11 Auto Adjust screen Key Specifi cation Auto Adjust Start : Start automatic adjustment. Cancel, Return : Transfer to Test Mode Main screen 3.12 Inverter screen Change the inverter frequency. The Inverter screen is shown in Figure 3.12. Return Inverter Check LowHigh Figure 3.12 Inverter screen Key Specifi cation Low : Set the inverter frequency at Low level. High : Set the inverter frequency at High level. Return : Transfer to Test Mode Main screen 3.13 NAVI screen Check the system in preparation for updating the Naviga- tion MAP data. The NAVI screen is shown in Figure 3.13. CancelReturn NAVI MAP Update CheckNAVI MAP Update Check ? NAVI OK/NGNAVI Check Figure 3.13 NAVI screen Key Specifi cation NAVI Check : Access Navigation to update NAVI MAP. Cancel : Transfer to Test Mode Main screen Return : Re-start the system in the normal mode. Note that the screen will be blanked for a moment after the NAVI Check is executed. Regardless of the result (OK or NG) of the check, the system clears the Test mode after this check and it is re- started in the normal mode 4 Functional specifi cation This section describes the test mode specifi cation in each function. 4.1 Display In the Test mode, the display is exclusively used for the test but screens for Source Control, Audio Control and Setup are same as those that are normally used. The system shows the touch position (+). However, it is not shown in the Touch Adjust screen (under adjustment). 4.2 Key The hard key specifi cation is listed in Table 4.2. (Note that the keys that are not listed in the table have conventional functions.) Table 4.2 Hard key KeyKVTDDX/DNX AutoMotor driver- Press and hold NAV key DVD audio and video switching DVD audio and video switching (Reference) Mode DescriptionKVTDDX/DNX Test ModeOPEN+SRC+ResetSRC+ATT+Reset Span switching SRC+VOL.DW+ Reset NAV+EJECT+Reset DC Offset/Service/ Memory Other Clear EJECT+AUTO+ Reset SRC+FUNC+Reset Retailer mode: ON EJECT+VOL.DW+ Reset EJECT+FUNC+ Reset Retailer mode: OFFSRC+ResetSRC+Reset RDS test drive modeEJECT+ATT+ResetEJECT+ATT+Reset 4.3 Remote controller The remote controller key specifi cation is listed in Table 4.3. (Note that the keys that are not listed in the table have con- 21 DDX5022/5022Y/5032/5032M/512/52RY DNX5120/512EX/5220/5220BT TEST MODE ventional functions.) The mode of the remote controller shall be “AUDIO”. Table 4.3 Remote Controller key KeyFunction Band (FM+) DVD video inspection switching M/S (AM-) DVD audio inspection switching Tenkey0Flicker Adjustment Tenkey1 Illumination switching (Switch from Red to Green or vice versa (RedGreen) only at KVT) Other than variable key Tenkey2Check DC Offset Tenkey3Change the V-IN (R-CAM) mirror mode switching Tenkey5NAVI forced interruption (Audio) Tenkey6Call Screen Adjustment screen Tenkey7 Direct call of variable illumination green Tenkey8 Direct call of variable illumination blue Tenkey9 Direct call of variable illumination red 4.4 Video Control In conjunction with change of the audio source, change AV-OUT (In the case of Graphic and NAVI, use AV-IN in stead of AV-OUT). AVIN AV-OUT: AVIN iPod AV-OUT: iPod DVD AV-OUT: DVD USB AV-OUT: USB TV AV-OUT: TV 4.5 Tuner When unable to access E2PROM, display Error (on the Tuner screen). K3I forced switching Forced to Narrow by pressing and hold Preset 4: xxx. x1MHz Forced to Middle by pressing and holding Preset 5: xxx. x2MHz Forced to Wide by pressing and holding Preset 6: xxx. x3MHz KVT: SRC key+VOL.DW key+Reset key DDX/DNX: NAV key+EJECT key+Reset key Use the above keys to change between Span (KM). Span information is displayed on the Information screen. When RDS PS is “RDS_TEST” in the Tuner source, turn OFF P-CON. 4.6 TV Tuner In the case of destination E, the default value of TV1 shall be “Area 5 (Russia), 8ch (191.25MHz)” (when KTC-V500 is connected). In the case of destination E, the default value of TV1 shall be “Area 4 (Russia), 8ch (191.25MHz)” (when KTC-V300 is connected). If started up as above, even if the Test mode is cleared by ACC, Power OFF ON, the setting values are main- tained. (The default value is resumed by the Reset.) 4.7 DVD Use CD media KTD-02A, DVD media TDV-540A/TTD-100 to play back in the order of the following sequence. Use “Title1-Chapter1” while Loading. Check CDDA (KTD-02A) Use “Track UP/DW” to play back in the order of sequence as shown below: 1 9 15 10 11 12 13 14 9 1. Track 28 is directly selected by pressing RDM key. DVD audio/video checking (TDV-540A) Use “Chapter UP/DW” to play back in the order of se- quence as shown in Tables 4.7 and 4.8. Use FM/AM on the remote controller to change the video/ audio check. Table 4.7 DVD Video check For DVD video checking. TitleChapter 36LevelAudiostream1 317AM/PM noiseAudiostream1 38 Frequency characteristics Audiostream1 312Color measurement Audiostream1 411kHz 0dBPCM96k/24bit Audiostream3 4617HzPCM96k/24bit Audiostream3 Table 4.8 DVD Audio check For DVD audio checking. TitleChapter 411kHz 0dBPCM96k/24bit Audiostream3 4617HzPCM96k/24bit Audiostream3 41644kHzPCM96k/24bit Audiostream3 42 Infi nityPCM96k/24bit Audiostream3 43LPCM96k/24bit Audiostream3 44RPCM96k/24bit Audiostream3 411kHz 0dBDolbyAudiostream1 42 Infi nityDolbyAudiostream1 22 DDX5022/5022Y/5032/5032M/512/52RY DNX5120/512EX/5220/5220BT 4.8 Audio The default setting of Volume shall be Step 30. In setting up BAL/FAD, the setting “MIN CENT MAX” can be made by 1 click. In setting up Xover, the setting “MIN MAX” can be made by 1 click. In setting up Tone, the setting “MIN CENT MAX” can be made by 1 click. The default setting of Tone (EQ) shall be Flat. The default setting of System Q shall be Off. When there is Digital Out terminal, the setting shall be such that the output is always On. The default setting of Line Mute shall be On. 4.9 AVIF The default setting of AVIN Interruption shall be On. The default setting of R-CAM Interruption shall be On. Normally an interruption occurs when the R-CAM is de- tected. Reverse condition shall be always On. The default setting of SP for NAVI interruption shall be Front ALL. Use Tenkey 3 on the remote controller to change V-IN mir- ror mode. 4.10 Screen adjustment By pressing Tenkey 5 on the remote control on each video screen, each video screens Screen adjustment items are displayed. The default value is Center.1Items can move between “Full Down Center Full Up” by 1 click. The default setting of DIMMER Mode shall be SYNC. 4.11 DC Offset DC Offset detection status (normal/error) clear Clear DC Offset detection information of E2PROM with DC Offset detection information Clear key on the Ser- vice Information screen. DC Offset detection information is displayed on the Infor- mation screen/Service Information screen. In the Test mode, even if DC Offset is detected, it is not written into E2PROM. However, the detection operation shall be carried out and when the DC Offset is detected, the Protect shall be dis- played and it becomes all CH Mute operation. Volume setting can be changed to the following settings by pressing Tenkey 2 on the remote controller. Source : DVD Assigned DISC : KTD-02A Assigned Track : 15 (20Hz, 0dB) Assigned VOL : 26 Step (Low) 4.12 Flicker adjustment q Use Tenkey 0 on the remote controller to turn the Flicker adjustment On. w Slide the monitor at the fore ground, and make the screen mode FULL, and set the video to “KVT: VIDEO, DDX/ DNX: R-CAM”. e Press Tenkey 0 on the remote controller during the fl icker adjustment to turn the adjustment Off. r Slide the monitor innermost (Test mode default value), make the screen mode FULL, and make the video as it is changed and used during the adjustment. The OSD can be shown normally during the fl icker ad- justment. When changing R-CAM of DDX/DNX, the detection at the Reverse terminal is neglected and the system is switched to R-CAM. 4.13 Driver for Panel Mechanism Motor (Only in KVT Series) With the condition when AUTO key is pressed and hold, the driver port for motor shall be turned On. While AUTO key is being pressed, the motor is turned On in reverse direction when the key is On for the fi rst time and the motor is stopped when the key is Off. With the key is pressed On for the second time, the motor is tuned On in the normal (forward) direction, and the mo- tor is stopped when the key is Off. Repeat the same steps in the succeeding procedure. 4.14 Clearing E2PROM contents Clear the E2PROM contents which should not remain in it when shipping the unit. KVT: EJECT key + AUTO key DDX/DNX: SRC key + FNC key Clear the contents of E2PROM using the above key + Reset key. Clear OK : Key illumination blinks (twice) Clear NG : Nothing happens. The following information is cleared: DC Offset information / Memory information / Retailer mode information / Service information If a jig is connected and the region is written in, the follow- ing information shall be cleared. When region code has been written in E2PROM, contents TEST MODE 23 DDX5022/5022Y/5032/5032M/512/52RY DNX5120/512EX/5220/5220BT of the E2PROM are not cleared if the same region code is written. Only when the different region code is written, contents of the E2PROM are not cleared. Serial No. / Security code / Touch correction / HPOSI correction / Chroma adjustment DC Offset information / Memory function / Retailer mode information / Service information Note: Since the above data is cleared (un-defi ned) when the E2PROM has been replaced during the service, it is required to re-adjust the data in the Test mode. 4.15 Security Code writing-in When entering the Security Code that is defi ned as a pair of the serial number of the product (for other destinations than K/R), use Security Set Up key on the Setup screen to call the Security screen. Only when the Security Code of E2PROM of the product for other destinations than K/R is blank, Set key is shown and press that key. In the Security Code Writing screen, run the same opera- tion as when registering Security Code in normal mode, and press the Enter key to start writing. Note: The Security Code to be entered in the above step is the set-specifi c code linked to the serial No. Writing of the code is successfully completed when “Complete” is displayed, and if “NG” is displayed, the writing the code is unsuccessfully completed. Note: If “NG” is displayed, transfer to the Test mode again and repeat the above process from the 1st step. When the Security Code is Blank, the system is turned OFF in 30 minutes. Note: In order to turn Security Off in the product whose destination is K/R while the Security of that product is turned On, turn the Security off from the Setup screen, or use the following steps to turn the Security off on the Security Code Input screen shown when the system is turned on: Press Tenkey 5 on the remote controller twice Tenkey 2 four times Tenkey 7 three times. 4.16 Other Do not operate the Back Up Memory function during the Test mode. In the Test mode, the color of illumination shall be white. The key illumination is in white but GUI shall be the ini- tial value, and if the color is changed by the Setup this change of color is shown together with GUI/ key. TEST MODE 24 DDX5022/5022Y/5032/5032M/512/52RY DNX5120/512EX/5220/5220BT ADJUSTMENT List of Adjustment and Check Items for DVS-802xV and 812xV 1. Adjustments after replacement of pickup The mechanism shall be adjusted to reduce variations among parts, which are inherent to the machine. No.ItemOverviewDisc 1Offset Cancel Adjust Stray light offset in the optical module - 2Inner Limit Adjust Support recording of minimum limit for DVD+R/RW (To decide the focus on position.) -