Pioneer-VSX41-avr-sm电路图 维修手册.pdf

ORDER NO. PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 PIONEER CORPORATION 2002 RRV2614 THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S). T ZZK MAY. 2002 Printed in Japan Model No.Order No.Remarks VSX-D811S/KUXJIRRV2583 This service manual should be used together with the following manual(s): AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX-41 Type Model Power RequirementRemarks VSX-41 KUXJI/CAAC120V RadioFans.CN 收音机爱 好者资料库 VSX-41 2 jpfy For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 1. CONTRAST OF MISCELLANEOUS PARTS CONTRAST TABLE VSX-41/KUXJI/CA and VSX-D811S/KUXJI are constructed the same except for the following : Parts marked by NSP are generally unavailable because they are not in our Master Spare Parts List. The mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Screws adjacent to mark on product are used for disassembly. Reference Nos. indicate the pages and Nos. in the service manual for the base model. NOTES: Notes : For PCB ASSEMBLIES, Refer to “CONTRAST OF PCB ASSEMBLIES” and “2. SCHEMATIC DIAGRAM”. Part No. Ref. No.MarkSymbol and DescriptionVSX-D811SVSX-41Remarks /KUXJI/KUXJI/CA PCB ASSEMBLIES P9 - 1DD it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician. WARNING This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause cancer, birth defects or other reproductive harm. Health & Safety Code Section 25249.6 Proposition 65 NOTICE (FOR CANADIAN MODEL ONLY) Fuse symbols (fast operating fuse) and/or (slow operating fuse) on PCB indicate that replacement parts must be of identical designation. REMARQUE (POUR MODLE CANADIEN SEULEMENT) Les symboles de fusible (fusible de type rapide) et/ou (fusible de type lent) sur CCI indiquent que les pices de remplacement doivent avoir la mme dsignation. ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED BEFORE RETURN- ING THE APPLIANCE TO THE CUSTOMER. 2. PRODUCT SAFETY NOTICE Many electrical and mechanical parts in the appliance have special safety related characteristics. These are often not evident from visual inspection nor the protection afforded by them necessarily can be obtained by using replacement components rated for voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this Service Manual. Electrical components having such features are identified by marking with a on the schematics and on the parts list in this Service Manual. The use of a substitute replacement component which does not have the same safety characteristics as the PIONEER recommended replacement one, shown in the parts list in this Service Manual, may create shock, fire, or other hazards. Product Safety is continuously under review and new instructions are issued from time to time. For the latest information, always consult the current PIONEER Service Manual. A subscription to, or additional copies of, PIONEER Service Manual may be obtained at a nominal charge from PIONEER. (FOR USA MODEL ONLY) 1. SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Measure leakage current to a known earth ground (water pipe, conduit, etc.) by connecting a leakage current tester such as Simpson Model 229-2 or equivalent between the earth ground and all exposed metal parts of the appliance (input/output terminals, screwheads, metal overlays, control shaft, etc.). Plug the AC line cord of the appliance directly into a 120V AC 60 Hz outlet and turn the AC power switch on. Any current measured must not exceed 0.5 mA. Device under test Leakage current tester Earth ground Reading should not be above 0.5 mA Also test with plug reversed (Using AC adapter plug as required) Test all exposed metal surfaces AC Leakage Test VSX-D811S-K3 5678 56 7 8 C D F A B E Important symbols for good services In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely. When you find the procedures bearing any of the symbols, be sure to fulfill them: 2. Adjustments To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable. In accordance with the procedures or instructions described in this manual, adjustments should be performed. 3. Cleaning For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning, proper cleaning should be performed to restore their performances. 5. Lubricants, glues, and replacement parts Appropriately applying grease or glue can maintain the product performances. But improper lubrication or applying glue may lead to failures or troubles in the product. By following the instructions in this manual, be sure to apply the prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed ones should be used. 4. Shipping mode and shipping screws To protect the product from damages or failures that may be caused during transit, the shipping mode should be set or the shipping screws should be installed before shipping out in accordance with this manual, if necessary. 1. Product safety You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and should keep the safety during servicing by following the safety instructions described in this manual. VSX-D811S-K4 1234 1234 C D F A B E CONTENTS SAFTY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 1. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 2. EXPLODED VIEWS AND PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 2.1 PACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 2.2 EXTERIOR SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 2.3 FRONT PANEL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.1 BLOCK DIAGRAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.2 OVERALL WIRING CONNECTION DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.3 D.D & INPUT (1/4) ASSY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 3.4 D.D & INPUT (2/4) ASSY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 3.5 D.D & INPUT (3/4) ASSY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 3.6 D.D & INPUT (4/4) ASSY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 3.7 AMP & PRIMARY (1/2), TRANS2 and TRANS3 ASSYS . . . . . . . . . . . . . . . . . . . . . . . . 24 3.8 AMP & PRIMARY (2/2), REG. , HASHIGETA, B TO B and TRANS1 ASSYS . . . . . . . . . . . . . . 26 3.9 DIGITAL IN and KAWA ASSYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 3.10 VIDEO, 6CH IN and S. VIDEO ASSYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 3.11 FRONT, R. ENCODER and POWER SW ASSYS . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 3.12 TRANS4, F. VIDEO, F. OPTICAL, H. P. , M. SW and PRI-OUT ASSYS . . . . . . . . . . . . . . . . 34 3.13 FM/AM TUNER MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 4. PCB CONNECTION DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 4.1 TRANS2, TRANS3, TRANS1 and TRANS4 ASSYS. . . . . . . . . . . . . . . . . . . . . . . . . . . 39 4.2 DD & INPUT ASSY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 4.3 AMP & PRIMARY, AMP INPUT and MECHA SW ASSYS. . . . . . . . . . . . . . . . . . . . . . . . 44 4.4 FRONT, R. ENCODER, POWER SW and H. P. ASSYS . . . . . . . . . . . . . . . . . . . . . . . . . 46 4.5 REGULATOR, HASHIGETA and KAWA ASSYS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 4.6 BOARD TO BOARD, DIGITAL IN, VIDEO and 6CH IN ASSYS . . . . . . . . . . . . . . . . . . . . . 52 4.7 S. VIDEO, FRONT VIDEO, FRONT OPTICAL and PRI-OUT ASSYS . . . . . . . . . . . . . . . . . . 54 4.8 FM/AM TUNER MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 5. PCB PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 6. ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 6.1 TUNER SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 7. GENERAL INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 7.1 PCB LACATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 7.2 PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 7.2.1 IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 7.2.2 DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 7.3 EXPLANATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 7.3.1 U-COM BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 7.3.2 POWER ON AND OFF SEQUENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 7.3.3 PROTECTION CIRCUIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 7.4 CLEANING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 8. PANEL FACILITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 VSX-D811S-K5 5678 56 7 8 C D F A B E 1. SPECIFICATIONS Accessories Remote control unit (XXD3044) AM loop antenna (ATB7009) FM wire antenna (ADH7005) AA size IEC R6P Dry cell batteries (x2) Miscellaneous Power Requirements UK model . AC 230 V, 50/60 Hz European model. AC 220-230 V, 50/60 Hz Power Consumption VSX-D811S.280W In Standby. 1 W Dimensions .420 (W) x 158 (H) x 401 (D) mm Weight (without package) VSX-D811S. 10 kg Furnished Parts AM loop antenna . 1 FM wire antenna . 1 Dry cell batteries (AA size IEC R6P). 2 Remote control. 1 Operating instructions . 1 Specifications and the design are subject to possible modifications without notice, due to improvements. DTS ,DTS-ES Extended Surround and Neo:6 are trademarks of Digital Theater Systems, Inc. Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the double D symbol are trademarks of Dolby Laboratorories. Amplifier Section Continuous Power Output (STEREO mode) Front . 100 W per channel (DIN 1kHz, THD 1.0 %, 8 ) Continuous Power Output Front . 100 W per channel (1kHz, THD 1.0 %, 8 ) Center . 100 W (1kHz, THD 1.0 %, 8 ) Surround . 100 W per channel (1kHz, THD 1.0 %, 8 ) Surround Back . 100 W per channel (1kHz, THD 1.0 %, 8 ) Above specifications are applicable when the power supply is 230V. Input (Sensitivity/Impedance) CD, VCR/DVR, CD-R/TAPE/MD, DVD/LD, TV/SAT . 200 mV/47 k Frequency Response CD, VCR/DVR, CD-R/TAPE/MD, DVD/LD, TV/SAT . 5 Hz to 100,000 Hz dB Output (Level/Impedance) VCR/DVR REC, CD-R/TAPE/MD REC . 200 mV/2.2 k Tone Control BASS . 6 dB (100 Hz) TREBLE . 6 dB (10 kHz) LOUDNESS . +9 dB/+9 dB (100 Hz/10 kHz) Signal-to-Noise Ratio DIN (Continuous rated power output/50 mW) CD, VCR/DVR, CD-R/TAPE/MD,DVD/LD, TV/SAT .96 dB Video Section Input (Sensitivity/Impedance) VCR/DVR, DVD/LD, TV/SAT . 1 Vp-p/75 Output (Level/Impedance) VCR/DVR . 1 Vp-p/75 Frequency Response VCR/DVR, DVD/LD,TV/SAT MONITOR. 5 Hz to 7 MHz dB Signal-to-Noise Ratio .55 dB FM Tuner Section Frequency Range. 87.5 MHz to 108 MHz Usable Sensitivity.Mono:13.2 dBf, IHF (1.3 V/ 75 ) 50 dB Quieting Sensitivity . Mono: 20.2 dB Stereo: 38.6 dBf Signal-to-Noise Ratio . Mono: 73 dB (at 85 dBf) Stereo: 70 dB (at 85 dBf) Signal-to-Noise Ratio (DIN) . Mono: 62 dB Stereo: 58 dB Distortion. Stereo: 0.5 % (1 kHz) Alterna