Pioneer-XDJR1-mp-sm 电路图 维修手册.pdf

ORDER NO. PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 PIONEER CORPORATION2013 2013 Printed in Japan XDJ-R1 RRV4401 DJ SYSTEM XDJ-R1 THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S). ModelTypePower RequirementRemarks XDJ-R1SVWYXE8AC 220 V to 240 V XDJ-R1CUXEAC 120 V XDJ-R1FLWPWXEAC 110 V to 120 V or 220 V to 240 V XDJ-R1KXE5AC 220 V XDJ-R1AXE5AC 220 V to 240 V K-MZV JUNE RadioFans.CN 收音机爱 好者资料库 2XDJ-R1 1234 A B C D E F 1234 SAFETY INFORMATION LABEL CHECK WARNING This product may contain a chemical known to the State of California to cause cancer, or birth defects or other reproductive harm. Health it is not meant for the casual do-it- yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician. WARNING ! THE AEL (ACCESSIBLE EMISSION LEVEL) OF THE LASER POWER OUTPUT IS LESS THAN CLASS 1 BUT THE LASER COMPONENT IS CAPABLE OF EMITTING RADIATION EXCEEDING THE LIMIT FOR CLASS 1. A SPECIALLY INSTRUCTED PERSON SHOULD DO SERVICING OPERATION OF THE APPARATUS. LASER DIODE CHARACTERISTICS For CD Wave length : 775 - 800 nm Output Power : Less than Class 1 for KXE5 for FLWPWXEfor SVWYXE8for CUXE for AXE5 RadioFans.CN 收音机爱 好者资料库 3XDJ-R1 5678 5678 A B C D E F CONTENTS SAFETY INFORMATION.2 1. SERVICE PRECAUTIONS.4 1.1 NOTES ON SOLDERING.4 2. SPECIFICATIONS.5 3. BASIC ITEMS FOR SERVICE .6 3.1 CHECK POINTS AFTER SERVICING .6 3.2 JIGS LIST.6 3.3 PCB LOCATIONS.7 4. BLOCK DIAGRAM .8 4.1 OVERALL WIRING DIAGRAM .8 4.2 OVERALL BLOCK DIAGRAM.10 4.3 SYSTEM BLOCK DIAGRAM.12 4.4 LEVEL BLOCK DIAGRAM.14 5. DIAGNOSIS .16 5.1 TROUBLESHOOTING.16 5.2 CONFIMATION OF WIRELESS LAN COMMUNICATION.19 5.3 ERROR CODE LIST.20 6. SERVICE MODE.21 6.1 SERVICE MODE .21 7. DISASSEMBLY .28 8. EACH SETTING AND ADJUSTMENT.39 8.1 NECESSARY ITEMS TO BE NOTED.39 8.2 UPDATING OF THE FIRMWARE.40 8.3 USER SETABLE ITEMS.41 9. EXPLODED VIEWS AND PARTS LIST.42 9.1 PACKING SECTION.42 9.2 EXTERIOR SECTION .44 10. SCHEMATIC DIAGRAM.48 10.1 I/O ASSY .48 10.2 MIXER, CH, CROSS FADER, USB and PHONES ASSEMBLIES.50 10.3 DSP & POWER ASSY (1/2) and Wi-Fi PCB ASSY.52 10.4 DSP & POWER ASSY (2/2).54 10.5 CD1 and CD2 ASSEMBLIES.56 10.6 SERVO ASSY.58 10.7 SWITCHING POWER.60 10.8 WAVEFORMS.62 11. PCB CONNECTION DIAGRAM.64 11.1 I/O ASSY .64 11.2 MIXER ASSY.66 11.3 DSP & POWER ASSY.68 11.4 CH, CROSS FADER, USB and PHONES ASSEMBLIES.70 11.5 Wi-Fi PCB ASSY .71 11.6 CD1 and CD2 ASSEMBLIES.72 11.7 SERVO ASSY.74 11.8 SWITCHING POWER.75 12. PCB PARTS LIST.76 RadioFans.CN 收音机爱 好者资料库 4XDJ-R1 1234 A B C D E F 1234 1. SERVICE PRECAUTIONS 1.1 NOTES ON SOLDERING For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit. Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs accompanied by reworking of soldering. Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C. Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 C in general, although the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of the soldering iron. Do NOT use a soldering iron whose tip temperature cannot be controlled. Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. 5XDJ-R1 5678 5678 A B C D E F 2. SPECIFICATIONS Power requirements.AC 220 V to 240 V, 50 Hz/60 Hz (SVWYXE8) AC 120 V, 60 Hz (CUXE) AC 110 V to 120 V or 220 V to 240 V, 50 Hz/60 Hz (FLWPWXE) AC 220 V, 60 Hz (KXE5) AC 220 V to 240 V, 50/60 Hz (AXE5) Power consumption.30 W Power consumption (standby) .0.5 W Main unit weight.6.8 kg (15 lb) Max. dimensions.623 mm (W) 107.7 mm (H) 308.4 mm (D) (24.6 in. (W) 4.3 in. (H) 12.2 in. (D) Tolerable operating temperature. +5 C to +35 C (+41 F to +95 F) Tolerable operating humidity.5 % to 85 % (no condensation) Wireless LAN section Supported standards.IEEE 802.11b/g (2.4 GHz band) Audio Section Sampling rate .44.1 kHz A/D, D/A converter. 24 bits Frequency characteristic USB/LINE. 20 Hz to 20 kHz S/N ratio (MASTER OUT 1, rated output, A-WEIGHTED) USB (when external input terminal not connected).98 dB LINE.97 dB CD.97 dB PHONO.86 dB MIC.80 dB Total harmonic distortion (MASTER OUT 1, 20 Hz 20 kHzBW) USB.0.006 % LINE.0.007 % Standard input level / Input impedance LINE.12 dBu/47 k PHONO.48 dBu/47 k MIC.52 dBu/10 k AUX .12 dBu/10 k Standard output level / Load impedance / Output impedance MASTER OUT 1. +6 dBu/10 k/330 or lower MASTER OUT 2. +2 dBu/10 k/1 k BOOTH. +2 dBu/10 k/1 k PHONES .+2 dBu/32 /66 Rated output level / Load impedance MASTER OUT 1.+22 dBu/10 k MASTER OUT 2.+18 dBu/10 k Crosstalk (20 Hz 20 kHzBW) LINE.83 dB Channel equalizer characteristic HI. to + 9 dB (13 kHz) MID. to + 9 dB (1 kHz) LOW. to +9 dB (70 Hz) Microphone equalizer characteristic LOW CENTER HI.12 dB (10 kHz) to 0 dB to 12 dB (100 Hz) Input/output terminals USB downstream port Type A.1 set Power supply.5 V/500 mA or less USB upstream port B type .1 set MASTER OUT 1 output terminal XLR connector.1 set MASTER OUT 2 output terminal RCA pin jacks.1 set BOOTH output terminal RCA pin jacks.1 set PHONES output terminal Stereo phone jack ( 6.3 mm) .1 set Stereo mini phone jack ( 3.5 mm).