Philips-FWC-28-Service-Manual(1) 电路图 维修手册.pdf

PCS 103 446 Service Service Service Service Service FW-C28/21M/22/34 TABLE OF CONTENTS Page Location of pc boards fr Reparaturen sind Original-Ersatzteile zu verwenden. I Le norme di sicurezza esigono che lapparecchio venga rimesso nelle condizioni originali e che siano utilizzati i pezzi di ricambio identici a quelli specificati. After servicing and before returning set to customer perform a leakage current measurement test from all exposed metal parts to earth ground to assure no shock hazard exist. The leakage current must not exceed 0.5mA. CLASS 1 LASER PRODUCT 3122 110 03420 GBWarning ! Invisible laser radiation when open. Avoid direct exposure to beam. SVarning ! Osynlig laserstrlning nr apparaten r ppnad och sprren r urkopplad. Betrakta ej strlen. SFVaroitus ! Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina nkymttmlle laseristeilylle. l katso steeseen! DKAdvarse ! Usynlig laserstrling ved bning nr sikkerhedsafbrydere er ude af funktion. Undg udsaettelse for strling. 1-6 PCS 90 115 2-1 PCS 103 449 English 5 General Information The type plate (which contains the serial number) is located at the rear of the system. Recording is permissible if copyright or other rights of third parties are not infringed. This product complies with the radio interference requirements of the European Community. Environmental Information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet). Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment. Accessories(Supplied) Remote control Batteries (two AA size) for remote control AM loop antenna FM wire antenna AC power cord Safety Information Before operating the system, check that the operating voltage indicated on the typeplate (or the voltage indication beside the voltage selector) of your system is identical with the voltage of your local power supply. If not, please consult your dealer. The typeplate is located at the rear of your system. When the system is switched on, do not move it around. Place the system on a solid base (e.g. a cabinet). Place the system in a location with adequate ventilation to prevent internal heat build-up in your system. Allow at least 10cm clearance from the rear and the top of the unit and 5cm from the each side. Do not expose the system to excessive moisture, rain, sand or heat sources. Under no circumstances should you repair the system yourself, as this will invalidate the warranty! CONTENTSGENERAL INFORMATIONSAFETY INFORMATION If the system is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lens of the CD unit inside the system. Should this occur, the CD player will not operate normally. Leave the power on for about one hour with no disc in the system until normal playback is possible. Electrostatic discharge may cause unexpected problems. See whether these problems disappear if you unplug the AC power cord and plug it in again after a few seconds. To disconnect the system from the power supply completely, remove the AC power plug from the wall socket. General Information .5 Safety Information .5 Preparation . 6 - 7 Controls. 8 - 9 Operating The System. 10 - 11 CD. 12 - 14 Tuner. 14 - 16 Tape . 17 - 18 AUX.18 Recording . 19 - 20 Clock .20 Timer. 21 Sleep Timer .21 Specifications .22 Maintenance.23 Troubleshooting . 23 - 24 6 English PREPARATION Rear Connections AM ANTENNA A B C D VOLTAGE SELECTOR 110V- 127V 220V- 240V AUX IN R + L + E AUDIO OUT LR AC MAINS FM AERIAL 75 2-2 PCS 103 450 English 7 A AM Loop Antenna Connection Connect the supplied loop antenna to the AM ANTENNA terminal. Place the AM loop antenna far away from the system and adjust its position for the best reception. B FM Wire Antenna Connection Connect the supplied FM wire antenna to the FM AERIAL (FM ANTENNA) 75 terminal. Adjust the position of the FM antenna for the best reception. Outdoor Antenna For better FM stereo reception, connect an outdoor FM antenna to the FM AERIAL (FM ANTENNA) 75 terminal using a 75 coaxial wire. FM ANTENNA 75FM AERIAL 75 OR C Speakers Connection Connect the right speaker to Front terminal R, with the colored wire to + and the black wire to -. Connect the left speaker to Front terminal L, with the colored wire to + and the black wire to -. Clip the stripped portion of the speaker wire as shown. unlocklock 12 mm D Connecting other equipment to your system You can connect the audio left and right OUT terminals of a TV, VCR, Laser Disc player, DVD player or CD Recorder to the AUX IN terminals at the rear of the system. E AC Power Supply After all other connections have been made, connect the AC power cord to the system and to the wall outlet. PREPARATION Inserting batteries into the Remote Control Insert the batteries (Type R06 or AA) into the remote control as shown in the battery compartment. + - + - To avoid damage from possible battery leakage, remove dead batteries or batteries that will not be used for a long time. For replacement, use type R06 or AA batteries. 8 English CONTROLS DIGITAL SOUND CONTROL DIGITAL SOUND CONTROL STANDBY-ON PROGRAM DIM FULL AUTO STOP VOLUME FW-C10MINI HIFI SYSTEM CD1 2 3BANDTAPE 1 2 TAPECDTUNERAUX PRESET TUNING STOPCLEARSEARCHPLAY PAUSEPREVNEXT DISC CHANGE DISC 3 OPENCLOSE DC 3CHANGER 3 CD ROTARY CHANGER SYSTEM CD REWRITABLE COMPATIBLE CD SYNCHRO RECORDING 3 CD ROTARY CHANGER SYSTEM CD REWRITABLE COMPATIBLE CD SYNCHRO RECORDING D B B VIDEO O P T I M A L J A Z Z R O C K T E C H N O DSC DISC 2DISC 1 RECORD DUBBING A.REPLAY RDSNEWSCLOCKTIMER PLAYBACK OPEN TAPE 2 OPEN TAPE 1 2 1 9 0 3 5 ! % ) # when the system is in standby or demonstration mode. “EASY SET” will be displayed, and followed by “TUNER” and then “AUTO”. EASY SET will start searching for all RDS radio stations with sufficient signal strength and then followed by radio stations on FM, MW and LW band respectively. Weak RDS radio stations may be stored in later presets. All available RDS and radio stations with sufficient signal strength will be stored. Up to 40 presets may be stored. 2 The system will proceed to set the RDS time automatically with the stored RDS preset station. If no RDS station is available in the first preset station, the program will exit automatically. After a radio station is found, “EASY SET” will be displayed and followed by “TIME” When searching RDS time; “SEARCH RDS TIME” will be displayed. When RDS time is read, “RDS TIME” will be displayed. The current time will be displayed for 2 seconds and stored automatically. Notes: EASY SET will start with the RDS station, if there are still presets available, it will continue to store the FM, MW and LW bands respectively. When EASY SET is used, all previously stored radio stations will be replaced. The last preset radio station or the first available RDS station will appear on the display when EASY SET is completed. If RDS station does not transmit RDS time within 90 seconds, the program will exit automatically and the display will show “NO RDS TIME”. Switching the system ON Press CD, TUNER, TAPE or AUX. You can also switch on the system by pressing any one of the CD DIRECT PLAY buttons. 2-4 PCS 103 452 English 11 Switching the system to standby mode Press STANDBY ON or B on the remote control. The system will switch to standby mode. Selecting the Source Press the respective source selection button: CD, TUNER, TAPE or AUX. The display indicates the selected source. Note: For an external source, make sure you have connected the audio left and right OUT terminals of the external equipment (TV, VCR, Laser Disc player, DVD player or CD Recorder) to the AUX IN terminals. DIM mode You can select the desired brightness for the display. Press DIM to select DIM 1, DIM 2, DIM 3 or DIM OFF display mode. TheDIMdisplay lights up. DIM 1, DIM 2, DIM 3 or DIM OFF will be displayed depending on the mode selected. OPERATING THE SYSTEM DIM OFF - normal brightness with Spectrum Analyzer On DIM 1 - normal brightness with Spectrum Analyzer Off DIM 2 - half brightness with Spectrum Analyzer On DIM 3 - half brightness with Spectrum Analyzer Off and all LEDs on the system will be switched off. Sound Control VOLUME ADJUSTMENT Adjust VOLUME to increase or decrease the sound level. For Personal Listening Connect the headphones plug to the n socket at the front of the system. The speakers will be muted. DIGITAL SOUND CONTROL (DSC) The DSC feature enables you to enjoy special sound effects that have preset equalizer settings, providing the best music reproduction. Press DSC to select OPTIMAL, JAZZ, ROCK or TECHNO. The Digital Sound Control display panel will light up respectively. “OPTIMAL, JAZZ, ROCK or TECHNO” and the respective flag will be displayed. Note: When OPTIMAL sound is selected, DBB will be switched on automatically. DYNAMIC BASS BOOST (DBB) The DBB mode enhances the bass response. Press DBB to switch on bass response. The DBB button lights up. “DBB ON” and the DBB flag will be displayed. To switch off DBB Press DBB again. The DBB button light is switched off. “DBB OFF” will be displayed. Note: Some CDs or tapes might be recorded in high modulation, which causes a distortion at high volume. If this occurs, switch off DBB or reduce the volume. MUTE (only on remote control) This feature allows you to temporarily switch off the sound of the system without switching off the system when you require a moment of silence. Press MUTE on the remote control to switch off the sound. MUTE and the MUTE flag will be displayed. Press MUTE again on the remote control or increase the VOLUME to switch on the sound. 12 English CD Warning! 1) This system is designed for conventional CDs. Do not use any accessories such as disc stabilizer rings or CD treatment sheets, etc., which may damage the CD mechanism. 2) Do not load more than one disc into each tray. 3) When the CD changer is loaded with CDs, do not turn over or shake the system. This may jam the changer. You may load three discs in the CD changer for continuous playback without interruption. 3 CD ROTARY CHANGER SYSTEM CD REWRITABLE COMPATIBLE CD SYNCHRO RECORDING 3 CD ROTARY CHANGER SYSTEM CD REWRITABLE COMPATIBLE CD SYNCHRO RECORDING DIGITAL SOUND CONTROL STANDBY-ON FW-C10MINI HIFI SYSTEM CD1 2 3BANDTAPE 1 2 TAPECDTUNERAUX PRESET TUNING STOPCLEARSEARCHPLAY PAUSEPREVNEXT DISC CHANGE DISC 3 OPENCLOSE DC 3CHANGER D B B VIDEO O P T I M A L J A Z Z R O C K T E C H N O DSC DISC 2DISC 1 VOLUME PROGRAM DIMRECORD DUBBING A.REPLAY DIGITAL SOUND CONTROL RDSNEWSCLOCKTIMER Discs for playback This system can play all digital audio CD, finalized digital audio CD-Recordable and finalized digital audio CD-Rewritable format discs. Loading the CD Changer 1 Press CD to select CD mode. 2 Press OPENCLOSE. The CD carousel tray slides out. 3 Load a CD with the printed side up in the right tray. You can load another disc in the left tray. To load the third disc, press the DISC CHANGE button. The CD carousel tray will rotate until the empty tray is ready for loading. 4 Press OPENCLOSE to close the CD carousel tray. The total number of tracks and the playing time of the selected disc appear on the display. Note: To ensure good system performance, wait until the CD changer completely reads the disc(s) before proceeding. CD Direct Play You can play a CD directly by pressing the DISC 1, DISC 2 or DISC 3 button. The CD player will stop at the end of playback of the selected disc. A lit button indicates that a disc is loaded in the disc tray. A flashing button indicates that a disc is playing. Playing a CD 1 Press to start playback. The disc tray, track number and elapsed playing time of the current track appear on the display. To interrupt playback, press. The playing time flashes. To resume playback, press again. 2 To stop playback, press . Note: All the available discs will play once, then stop. Disc Change You can change the outer two discs while the third inner disc is stopped or is playing. 1 Press DISC CHANGE. The CD carousel tray slides out. 2 Replace the discs in the left and right disc trays. If you press DISC CHANGE again during playback, the CD will stop playing. 2-5 PCS 103 453 English 13 The CD carousel tray will rotate until the inner tray is rotated out and is ready for changing. 3 Press OPENCLOSE to close the CD carousel tray. Selecting a desired track Selecting a desired track when playback is stopped 1 Press or until the desired track appears on the display. 2 Press to start playback. The selected track number and elapsed playing time appear on the display. Selecting a desired track during playback Press or until the desired track appears on the display. The selected track number and elapsed playing time appear on the display. If you press once it will skip to the beginning of the current track and play the track again. Note: Pressing during shuffling can only skip to the beginning of the current track. Searching for a particular passage during playback Press and hold or until the desired passage is located. The volume will be reduced. Play returns to normal when or is released. Programming Tracks Programming tracks of a loaded CD is possible when playback is stopped. The display will indicate the total tracks stored in the program. Up to 40 tracks can be stored in the memory in any order. When 40 tracks are stored and you attempt to store another track, the display will show “PROGRAM FULL”. 1 Load the desired discs in the disc trays. 2 Press PROGRAM to start programming. The PROG flag starts flashing. It will cancel any previously selected repeat mode. 3 Press the CD (CD 123) or DISC 1/2/3 button to select the disc. 4 Press or to select the desired track. 5 Press PROGRAM to store the track. Repeat steps 3 to 5 to store other discs and tracks. 6 Press once to end programming. The total number of tracks programmed and total playing time appear on the display. CD Notes: If the total playing time is more than “99:59“ or if one of the programmed tracks has a number greater than 30, then “-:-” appears on the display instead of the total playing time. If the system is reading the discs, programming is not possible