Philips-HTS-3357-Service-Manual(1) 电路图 维修手册.pdf

1 - 1 HTS3357/12/05 Copyright 2007 Philips Consumer Electronics B.V. Eindhoven, The Netherlands All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by KC-ET741 Service Audio Printed in The Netherlands Subject to modification ? DVD Hometheatre System Version 1.1 TABLE OF CONTENTS Chapter Location of PC Boards.1-2 Versions Variation 50 Hz Power Consumption .100 W Dimensions .340.4 x 48.5 x 435 (mm) (w x h x d) Weight .4.04 kg FRONT AND REAR SPEAKERS System . Full range Impedance .3 Speaker drivers .3” full range speaker Frequency response .120 Hz 20 kHz Dimensions .95.6 x 198.3 x 75 (mm) (w x h x d) Weight .0.62 kg/each REAR SPEAKERS System . Full range satellite Impedance .3 Speaker drivers .3” full range speaker Frequency response .120 Hz 20 kHz Dimensions .95 x 1184 x 73.7 (mm) (w x h x d) Weight .5.99 kg/each CENTRE SPEAKER System .2-way satellite Impedance .6 Speaker drivers .2 x 2.5” full range speaker+ 2” tweeter Frequency response .120 Hz 20 kHz Dimensions .435 x 93.5 x 67 (mm) (w x h x d) Weight .1.34 kg SUBWOOFER Impedance .6 Speaker drivers .203 mm (8”) woofer Frequency response .40 Hz 120 Hz Dimensions .159.5 x 355.5 x 370 (mm) (w x h x d) Weight .4.75 kg Specif cations subject to change without prior notice. RadioFans.CN 收音机爱 好者资料库 1 - 4 Service Tools: Universal Torx driver holder .4822 395 91019 Torx bit T10 150mm .4822 395 50456 Torx driver set T6-T20 .4822 395 50145 Torx driver T10 extended .4822 395 50423 Compact Disc: SBC426/426A Test disc 5 + 5A .4822 397 30096 SBC442 Audio Burn-in test disc 1kHz .4822 397 30155 SBC429 Audio Signals disc .4822 397 30184 Dolby Pro-logic Test Disc .4822 395 10216 SERVICE AIDS HANDLING CHIP COMPONENTS 1 - 5 NLWAARSCHUWING Alle ICs en vele andere halfgeleiders zijn gevoelig voor electrostatische ontladingen (ESD). Onzorgvuldig behandelen tijdens reparatie kan de levensduur drastisch doen verminderen. Zorg ervoor dat u tijdens reparatie via een polsband met weerstand verbonden bent met hetzelfde potentiaal als de massa van het apparaat. Houd componenten en hulpmiddelen ook op ditzelfde potentiaal. IAVVERTIMENTO Tutti IC e parecchi semi-conduttori sono sensibili alle scariche statiche (ESD). La loro longevit potrebbe essere fortemente ridatta in caso di non osservazione della pi grande cauzione alla loro manipolazione. Durante le riparazioni occorre quindi essere collegato allo stesso potenziale che quello della massa dellapparecchio tramite un braccialetto a resistenza. Assicurarsi che i componenti e anche gli utensili con quali si lavora siano anche a questo potenziale. GB Safety regulations require that the set be restored to its original condition and that parts which are identical with those specified, be used. Safety components are marked by the symbol ! . NL Veiligheidsbepalingen vereisen, dat het apparaat bij reparatie in zijn oorspronkelijke toestand wordt teruggebracht en dat onderdelen, identiek aan de gespecificeerde, worden toegepast. De Veiligheidsonderdelen zijn aangeduid met het symbol ! . F Les normes de scurit exigent que lappareil soit remis ltat dorigine et que soient utiliss les pices de rechange identiques celles spcifies. Less composants de scurit sont marqus ! . D Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu beachten. Der Original zustand des Gerts darf nicht verndert werden; fr Reparaturen sind Original-Ersatzteile zu verwenden. Sicherheitsbauteile sind durch das Symbol ! markiert. I Le norme di sicurezza esigono che lapparecchio venga rimesso nelle condizioni originali e che siano utilizzati i pezzi di ricambio identici a quelli specificati. Componenty di sicurezza sono marcati con ! . GB After servicing and before returning set to customer perform a leakage current measurement test from all exposed metal parts to earth ground to assure no shock hazard exist, The leakage current must not exceed 0.5mA. CLASS 1 LASER PRODUCT 3122 110 03420 GBWarning ! Invisible laser radiation when open. Avoid direct exposure to beam. SVarning ! Osynlig laserstrlning nr apparaten r ppnad och sprren r urkopplad. Betrakta ej strlen. SFVaroitus ! Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina nkymttmlle laseristeilylle. l katso steeseen! GBWARNING All ICs and many other semi-conductors are susceptible to electrostatic discharges (ESD). Careless handling during repair can reduce life drastically. When repairing, make sure that you are connected with the same potential as the mass of the set via a wrist wrap with resistance. Keep components and tools also at this potential. F ATTENTION Tous les IC et beaucoup dautres semi-conducteurs sont sensibles aux dcharges statiques (ESD). Leur longvit pourrait tre considrablement courte par le fait quaucune prcaution nest prise leur manipulation. Lors de rparations, sassurer de bien tre reli au mme potentiel que la masse de lappareil et enfiler le bracelet serti dune rsistance de scurit. Veiller ce que les composants ainsi que les outils que lon utilise soient galement ce potentiel. ESD DWARNUNG Alle ICs und viele andere Halbleiter sind empfindlich gegenber elektrostatischen Entladungen (ESD). Unsorgfltige Behandlung im Reparaturfall kan die Lebensdauer drastisch reduzieren. Veranlassen Sie, dass Sie im Reparaturfall ber ein Pulsarmband mit Widerstand verbunden sind mit dem gleichen Potential wie die Masse des Gertes. Bauteile und Hilfsmittel auch auf dieses gleiche Potential halten. DKAdvarse ! Usynlig laserstrling ved bning nr sikkerhedsafbrydere er ude af funktion. Undg udsaettelse for strling. F Pour votre scurit, ces documents doivent tre utiliss par des spcialistes agrs, seuls habilits rparer votre appareil en panne. GB ESD PROTECTION EQUIPMENT Complete Kit ESD3 (small tablemat, wristband, connection box, estention cable and earth cable .4822 310 10671 Wristband tester .4822 344 13999 1 - 6 Pb(Lead) Free Solder When soldering , be sure to use the pb free solder. INDENTIFICATION: Regardless of special logo (not always indicated) one must treat all sets from 1 Jan 2005onwards, according next rules: Important note: In fact also products of year 2004 must be treated in this way as long as you avoid mixing solder- alloys (leaded/ lead-free). So best to always use SAC305 and the higher temperatures belong to this. Due to lead-free technology some rules have to be respected by the workshop during a repair: Use only lead-free solder alloy Philips SAC305 with order code 0622 149 00106. If lead-free solder-paste is required, please contact the manufacturer of your solder-equipment. In general use of solder-paste within workshops should be avoided because paste is not easy to store and to handle. Use only adequate solder tools applicable for lead- free solder alloy. The solder tool must be able To reach at least a solder-temperature of 400?C, To stabilize the adjusted temperature at the solder- tip To exchange solder-tips for different applications. Adjust your solder tool so that a temperature around 360?C 380?C is reached and stabilized at the solder joint. Heating-time of the solder-joint should not exceed 4 sec. Avoid temperatures above 400?C otherwise wear-out of tips will rise drastically and flux-fluid will be destroyed. To avoid wear-out of tips switch off un- used equipment, or reduce heat. Mix of lead-free solder alloy / parts with leaded solder alloy / parts is possible but PHILIPS recommends strongly to avoid mixed solder alloy types (leaded and lead-free). If one cannot avoid or does not know whether product is lead-free, clean carefully the solder-joint from old solder alloy and re-solder with new solder alloy (SAC305). Use only original spare-parts listed in the Service- Manuals. Not listed standard-material (commodities) has to be purchased at external companies. Special information for BGA-ICs: Always use the 12nc-recognizable soldering temperature profile of the specific BGA (for de- soldering always use the lead-free temperature profile, in case of doubt) Lead free BGA-ICs will be delivered in so-called dry- packaging (sealed pack including a silica gel pack) to protect the IC against moisture. After opening, dependent of MSL-level seen on indicator-label in the bag, the BGA-IC possibly still has to be baked dry. (MSL=Moisture Sensitivity Level). This will be communicated via AYS-website. Do not re-use BGAs at all. For sets produced before 1.1.2005 (except products of 2004), containing leaded solder-alloy and components, all needed spare-parts will be available till the end of the service-period. For repair of such sets nothing changes. On our website www.atyourservice.ce.P you find more information to: BGA-de-/soldering (+ baking instructions) Heating-profiles of BGAs and other ICs used in Philips-sets You will find this and more technical information within the “magazine”, chapter “workshop news”. For additional questions please contact your local repair-helpdesk. 2 - 12 - 1 REPAIR INSTRUCTION (Part One) MAIN UNIT REPAIR CHART 1/3 A All function No working Check all system all cable is loose or bad INT Panel stanby LED show working or Not Re-insert and fix the cable Check back power PCB F901 bad cause damage Change F901 Check CN905 2pin BK5V if right Check repair control PCB Standby circuit Check +5V power supply circuit Check RB901 1pin +5V=5V Check repair switch power circuit ( See B) Check all Voltage 3.3V and 1.8V give circuit VCC=5V VD33=3.3V VD18=1.8V Check IC208 Pin234 OSC frequency 27MHz) Repair main pcb between IC202 IC206 IC208and IC602 circuit YES NO NO BAD NO OK YES WORK NO CHECK CORRECT YES YES B Power Supply No working All Voltage No Output Check F901 Bad Cause Damage Check BK5V +5V Working or Not No YES No +39V Voltage No Output Check Repair IC901 IC902 And Its conn circuit -27V Voltage No Output +12V Voltage No Output +5V Voltage No Output Check Q901 Q909 IC901 And Its Conjoint Part Check Q912 IC902 And Its Conjoint Part Check Q912 IC902 And Its Conjoint Part Check Q912 IC902 And Its Conjoint Part No C All Function No Sound Check POWER IC Voltage +39V Yes See Contents B CheckQ306 D304 ZD303 And Its conn parts Yes No Check Q305 C Voltage 3.3V OK No A All Function No Working B Power Supply No Working C All Function No Sound D Ipod input No Sound E Audio line IN No Output F Wireless No Output G DVD Audio No Sound H MP3 In No Sound I COAXIAL In No Sound L Tuner No Sound M No Svideo Output O HDMI No Output BK5V Voltage No Output Check Q912 IC902 And Its Conjoint Part CheckQ501 Q502 IC505 And Its conn parts OK LOW CheckQ902 ZD905 IC505 And Its conn parts Check Q902 C Voltage 3.3V OK No Check IC505 51PIN HIGH(3.3V) OR LOW(0V) Check IC501 IC502 IC503 IC504 And Its Conjoint Part P No CVBS Output Q No Y Pr Pb output RS NO SCART OUTPUT KARAOKE In No Sound 2 - 22 - 2 MAIN UNIT REPAIR CHART 2/3 No INT No G DVD Audio No Sound Check CN801 to DVD loader Cable Loose No OK Check Open/Close Working or Not Check CN802 CN803 to DVD Loader Cable loose or Bad INT Check IC801 And Its conjoint parts No or Bad INT Re-Insert and fix the cable YES Yes Determine Picture Output OK Yes or No Check IC208 And Their Conjoint Parts No Check Q801 Q802 Q803 OK Q804 And Their Conjoint Parts I COAXIAL In No Sound INT OK Check JK702 Pin5 INT OR NO REPAIR ok Check And Repair FB202 FB203 No Check IC201 IC208And OK Its Conjoint Parts Check IC201 Pin6 pin 23 approx +5.0V Yes or No D Ipod input No Sound Check DOCK TO HTS3540 Cable INT or No Check ipod input pcb JK101CN101 INT OR NO Change this Cable Change this TWO CheckCN101 JK101 Check DOCK INT OK INT OK Check CN101 5PIN Voltage Correct is 5.0V No No And Its Conjoint parts E AUX/TV IN No Output Check JK302 Check IC304 IC305 Pin7 INT or No approx -5.6V Pin16 approx +5.6V Check ZD301ZD302 Check FB307 FB308 Change this jk Check IC306 And Its Conjoint parts OK OK Check IC306 Pin1 Pin3 6 13 Voltage Correct is 5.0V Yes Yes or No FB309 Q904 See C OK H Check JK2 Check IC304 IC305 Pin7 INT or No approx -5.6V Pin16 approx +5.6VCheck ZD301ZD302 Check FB307 FB308 Change this jk Check IC306 And Its Conjoint parts OK No yes Check IC306 Pin1 Pin3 6 13 Voltage Correct is 5.0V Yes INT No Yes or No FB309 Q904 See C yes F Wireless No Output OK or No Check JK401 IC505 And Its conjoint parts No OK CheckJK401 Pin1 approx +5V See B OK See C Check IC403 PIN8 +12V And Its Conjoint Parts Check IC505 PIN29-32 And Its Conjoint Parts OK Check IC701 Its Conjoint Parts OK OK OK NO SCART OUTPUT OK S AUDIO VIDEO Repair IC505 And Its Conjoint Parts Check IC208 PIN137 PIN138 pin139 Its Conjoint Parts Check IC208 PIN134 Its Conjoint Parts Check SCART OUTPUT REPAIR INSTRUCTION (Part Two) 2 - 32 - 3 REPAIR INSTRUCTION (Part Three) MAIN UNIT REPAIR CHART 3/3 L Tuner No Sound Output Check CN301 Pin9= +9V Check CN301Q901 ZD904 No And Its Conjoint Parts Check SW Power See B Yes Check CN1 to CN301 Cable Loose or INT Check CN1 Pin2/Clock Pin3/Data,Pin4/CE Affirm Correct Yes No Check IC102 IC108 And Its Conjoint Parts No Check IC1 And No Its Conjoint Parts Check VT Valtage No Low Freq=0.8-1.8V Hi Freq=8.0-9.0V Check IC1 OSC Input Pin5-AM OSC VT No Change Pin3-FM OSC Rep