Sony-HCDDV2D-cs-sm 电路图 维修手册.pdf

SERVICE MANUAL Sony Corporation Audio Group Published by Sony Engineering Corporation US Model Canadian Model AEP Model UK Model E Model Australian Model DVD DECK RECEIVER 9-879-536-01 2005C1678-1 2005.03 Ver. 1.0 2005.03 SPECIFICATIONS HCD-DV2D HCD-DV2D is the Amplifier, DVD player, Tape Deck and Tuner section in CMT-DV2D. DVD Model Name Using Similar MechanismHCD-GP8D Section DVD Mechanism TypeKDA898ST Traverse Mechanism Name1ADOMEZ0412 TAPEModel Name Using Similar MechanismNEW SectionTape Transport Mechanism TypeCMAL5Z220C Continued on next page This system incorporates Dolby1) Digital and DTS2) Digital Surround System. 1) Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories. 2) Manufactured under license from Digital Theater Systems, Inc. “DTS” and “DTS 2.0 + Digital Out” are trademarks of Digital Theater Systems, Inc. Amplifier section AUDIO POWER SPECIFICATIONS (USA model only) POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 6 ohm loads, both channels driven, from 120 10,000 Hz: rated 50 watts per channel minimum RMS power, with no more than 10% total harmonic distortion from 250 milliwatts to rated output. North American model: Front speaker Continuous RMS power output (reference): 50 + 50 watts (6 ohms at 1 kHz, 10% THD) Total harmonic distortion less than 0.07% (6 ohms at 1 kHz, 25 W) European and Russian models: DIN power output (rated): 40 + 40 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 50 + 50 watts (6 ohms at 1 kHz, 10% THD) Music power output (reference): 100 + 100 watts (6 ohms at 1 kHz, 10% THD) Korean model: The following measured at AC 220 V, 60 Hz DIN power output (rated) 35 + 35 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference) 45 + 45 watts (6 ohms at 1 kHz, 10% THD) Other models: The following measured at AC 120 V, 240 V, 50/60 Hz DIN power output (rated) 40 + 40 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference) 50 + 50 watts (6 ohms at 1 kHz, 10% THD) Inputs TV IN (phono jacks):voltage 1 V, impedance 47 kilohms Outputs VIDEO OUT (phono jack) (except for European and Russian models): max. output level 1 Vp-p, unbalanced, Sync negative, load impedance 75 ohms LINE-TV (European and Russian models only): max. output level 1 Vp-p, unbalanced, Sync negative, load impedance 75 ohms DIGITAL OUT (OPTICAL) (Square optical connector jack, rear panel) Wavelength660 nm PHONES (stereo mini jack): accepts headphones of 8 ohms or more SPEAKER:accepts impedance of 6 ohms Disc player section SystemCompact disc and digital audio and video system LaserSemiconductor laser (DVD: =650 nm, CD: =780 nm) Emission duration: continuous Frequency responseDVD (PCM 48 kHz): 2 Hz 22 kHz (1 dB) CD: 2 Hz 20 kHz (1 dB) Video color system format Pan-American models: NTSC European and Russian models: PAL Other models: NTSC, PAL RadioFans.CN 收音机爱 好者资料库 2 HCD-DV2D SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1.A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2.A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3.Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) Fig. A.Using an AC voltmeter to check AC leakage. 1.5 k0.15 F AC voltmeter (0.75 V) To Exposed Metal Parts on Set Earth Ground SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY. Tape deck section Recording system4-track 2-channel stereo Frequency response40 13,000 Hz, using Sony TYPE I cassette Tuner section FM stereo, FM/AM superheterodyne tuner FM tuner section Tuning range87.5 108.0 MHz (50 kHz step) AntennaFM lead antenna Antenna terminals75 ohms unbalanced Intermediate frequency10.7 MHz AM tuner section Tuning range Pan-American models:530 1,710 kHz (with the tuning interval set at 10 kHz) 531 1,710 kHz (with the tuning interval set at 9 kHz) European and Russian models: 531 1,602 kHz (with the interval set at 9 kHz) Other models:530 1,710 kHz (with the interval set at 10 kHz) 531 1,602 kHz (with the interval set at 9 kHz) AntennaAM loop antenna Antenna terminalsExternal antenna terminal Intermediate frequency450 kHz General Power requirements North American model:120 V AC, 60 Hz European and Russian models: 230 V AC, 50/60 Hz Australian model:230 240 V AC, 50/60 Hz Korean model:220 V AC, 60 Hz Other models:110 120 V, 220 240 V AC, 50/60 Hz Adjustable with voltage selector Power consumption USA model:110 watts Canadian model:110 watts European and Russian models: 110 watts 0.3 watts (in Power Saving mode) Other models:120 watts Dimensions (w/h/d) (excl. speakers) Approx. 191 255 310 mm Mass (excl. speakers)Approx. 6.5 kg Design and specifications are subject to change without notice. RadioFans.CN 收音机爱 好者资料库 3 HCD-DV2D CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing Keep the temperature of the soldering iron around 270 C during repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. TABLE OF CONTENTS 1.SERVICING NOTES.4 2.GENERAL.5 3.DISASSEMBLY 3-1.Disassembly Flow .8 3-2.Cover Top, DC Fan.9 3-3.AMP Board, AV Board, Tuner (FM/AM) .9 3-4.MPEG Board . 10 3-5.DVD Mech Cover A/B . 10 3-6.Panel (DVD) . 11 3-7.DVD Loader (KDA898ST) . 11 3-8.Front Panel Section . 12 3-9.MAIN Board. 12 3-10. Cassette Deck Mechanism (CMAL5Z220C) . 13 3-11. FRONT Board . 13 3-12. Traverse Mech (1ADOMEZ0412) . 14 3-13. Lid TC . 14 4.TEST MODE. 15 5.MECHANICAL ADJUSTMENTS. 19 6.ELECTRICAL ADJUSTMENTS. 19 7.DIAGRAMS 7-1.Block Diagrams MPEG-1 Section . 22 MPEG-2 Section . 23 AUDIO Section . 24 PANEL/POWER Section . 25 7-2.Printed Wiring Board MAIN Section-1 . 26 7-3.Printed Wiring Board MAIN Section-2 . 27 7-4.Schematic Diagram MAIN Section . 28 7-5.Printed Wiring Board MPEG Section-1 . 29 7-6.Printed Wiring Board MPEG Section-2 . 30 7-7.Schematic Diagram MPEG Section . 31 7-8.Printed Wiring Board FRONT Section . 32 7-9.Schematic Diagram FRONT Section . 33 7-10. Printed Wiring Board AV/VIDEO OUT Section . 34 7-11. Schematic Diagram AV/VIDEO OUT Section . 35 7-12. Printed Wiring Board AMP/PT Section . 36 7-13. Schematic Diagram AMP Section . 37 7-14. Schematic Diagram PT Section (E3, E51, SP Model) . 38 7-15. Schematic Diagram PT Section (Except E3, E51, SP Model) . 39 8.EXPLODED VIEWS 8-1.Overall Section . 54 8-2.Front Panel Section . 55 8-3.Chassis Section. 56 8-4.DVD Mechanism Deck Section . 57 9.ELECTRICAL PARTS LIST. 58 Abbreviation E3: 240 V AC area in E model. E51 : Chilean and Peruvian model. SP: Singapore model. RadioFans.CN 收音机爱 好者资料库 4 HCD-DV2D SECTION 1 SERVICING NOTES The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick- up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. LASER DIODE AND FOCUS SEARCH OPERATION CHECK Carry out the “S curve check” in “CD section adjustment” and check that the S curve waveforms is output three times. NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT MODEL IDENTIFICATION Back Panel Power requirement indication ModelPower Voltage Indication US, CND models120 V AC, 60 Hz AEP, UK, RU models230 V AC, 50/60 Hz SP, E3, E51 models110 120 V/220 240V AC, 50/60 Hz KR model220 V AC, 60 Hz AUS model230 240 V AC, 50/60 Hz Abbreviation AUS: Australian model. CND: Canadian model. E3: 240 V AC area in E model. E51: Chilean and Peruvian model. KR: Korea model. RU: Russian model. SP: Singapore model. SERVICE POSITION OF THE TAPE CASSETTE MECHANISM DECK DISC TRAY LOCK The disc tray lock function for the antitheft of an demonstration disc in the store is equipped. Procedure : 1.Press the ?/1 button to turn the set ON. 2.Press the DVD u button to select “DVD” 3.Set disc on the tray, press the x button and the Z button simultaneously for five seconds. 4.The message “LOCKED” is displayed the tray is locked. 5.To release from this mode, press the x button and the Z button simultaneously for five seconds again. 6.The message “UNLOCKED” is displayed and the tray is unlocked. Note:When “LOCKED” is displayed, the slot lock is not released by turning power on/off with the ?/1 button. Tape Cassette Mechanism Deck (CMAL5Z220C) MAIN board Front Panel 5 HCD-DV2D SECTION 2 GENERAL This section is extracted from instruction manual. Main unit Cassette compartment qh (28) CD SYNC qk (28) Disc tray 3 (12) DISPLAY 5 (27, 34, 35, 36) Display window 2 PHONES jack qf PLAY MODE qj (13, 16, 44) PRESET EQ qd (30) Remote sensor 4 REPEAT qa (15) TUNER/BAND ws (25, 26, 29) TUNING +/ w; (25, 27) TV wa (29, 38) VOLUME +/ 0 (13, 27, 28) ?/1 (power) 1 (10, 44) Z (open/close) 6 (12) DVD NX (play/pause) 7 (10, 12, 23, 28, 39, 44) TAPE N (play) 8 (28) x (stop) 9 (10, 12, 26, 28, 31, 39, 44) Z PUSH OPEN (eject) qs (28) z REC PAUSE/START (record) ql (28, 31) m/M (rewind/fast forward) w; (13, 28) ./ (go back/forward) w; (12, 28) List of button locations and reference pages How to use this page Use this page to find the location of buttons and other parts of the system that are mentioned in the text. Illustration number r TUNER/BAND ws (25, 26, 29) RR Name of button/partReference page ALPHABETICAL ORDER A OP Z BUTTON DESCRIPTIONS 123546 7 8 9 0 qa qs qd qf qh qj qk w; ql wa ws 6 HCD-DV2D Remote control ANGLE qa (20) AUDIO qa (19, 31) CLEAR ql (16, 17, 23) CLOCK/TIMER SELECT 0 (33, 34) CLOCK/TIMER SET 0 (11, 32, 33) DIMMER 6 (34) DISPLAY 8 (34, 35, 36) DVD MENU 8 (14, 15) DVD SETUP 8 (11, 20, 21, 22, 24, 38, 44) DVD TOP MENU 8 (14) ENTER 8 qs (11, 14, 15, 17, 20, 21, 22, 25, 32, 33, 38, 44) FM MODE qh (27) KARAOKE PON qg (30) MUTING 9 (13, 27, 28) Number buttons* w; (14, 15, 16, 17, 22) PLAY MODE 7 (13, 16) PRESET +/ qk (25, 26) PRESET EQ qf (30) REPEAT qj (15) SLEEP wa (32) SUBTITLE qa (20) TIME SEARCH 2 (17) TUNER