Sony-STRK5-rec-sm 电路图 维修手册.pdf
SERVICE MANUAL FM STEREO/FM-AM RECEIVER E Model SPECIFICATIONS STR-K5 STR-K5 is the receiver section in HT-K5. Ver. 1.0 2006.03 9-887-119-01 2006C05-1 2006.03 Sony Corporation Home Audio Division Published by Sony Techno Create Corporation This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS* Digital Surround System. * Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. *“DTS” and “DTS Digital Surround” are registered trademarks of Digital Theater Systems, Inc. Amplifier section Power Output1) Models of area code SP, E51 (6 ohms 1 kHz, THD 0.7%) FRONT2):80 W/ch CENTER2):80 W SURR2):80 W/ch (6 ohms 1 kHz, THD 10%) FRONT2):110 W/ch CENTER2):110 W SURR2):110 W/ch 1) Measured under the following conditions: 2) Depending on the sound field settings and the source, there may be no sound output. Inputs (Analog) Inputs (Digital) Output (Analog) Reproduction frequency range: 20 20,000 Hz FM tuner section Tuning range87.5 108.0 MHz AntennaFM wire antenna Antenna terminals75 ohms, unbalanced Intermediate frequency10.7 MHz Area codePower requirements SP, MY230 V AC, 50 Hz E51240 V AC, 50 Hz SA-CD/CD, DVD, VIDEO 1, 2 Sensitivity: 800 mV Impedance: 50 k ohms DVD (Coaxial)Sensitivity: Impedance: 75 ohms SA-CD/CD (Optical)Sensitivity: Impedance: SUB WOOFERVoltage: 2 V Impedance: 1 k ohm AM tuner section Tuning range Models of area code SP With 9-kHz tuning scale:531 1,602 kHz Models of area code E51 With 10-kHz tuning scale: 530 1,610 kHz3) With 9-kHz tuning scale:531 1,602 kHz3) AntennaLoop antenna Intermediate frequency450 kHz 3) You can change the AM tuning scale to 9 kHz or 10 kHz. After tuning in any AM station, turn off the receiver. While holding down TUNING +, press ?/1. All preset stations will be erased when you change the tuning scale. To reset the scale to 10 kHz (or 9 kHz), repeat the procedure. General Power requirements Power consumption Power consumption (during standby mode) 0.2 W Dimensions (w/h/d) (Approx.) 430 145 296 mm including projecting parts and controls Mass (Approx.)7.0 kg Area codePower requirements SP, MY230 240 V AC, 50/60 Hz E51120/220/240 V AC, 50/60 Hz Area codePower consumption SP, MY, E51165 W Design and specifications are subject to change without notice. Abbreviation E51 : Chilean and Peruvian models MY : Malaysia model SP: Singapore model RadioFans.CN 收音机爱 好者资料库 2 STR-K5 Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. About area codes The area code of the receiver you purchased is shown on the lower portion of the rear panel (see the illustration below). Any differences in operation, according to the area code, are clearly indicated in the text, for example, “Models of area code AA only”. CENTER L LR S FRONT R 2-XXX-XXX-XX AA Area code TABLE OF CONTENTS 1.GENERAL.3 2.DISASSEMBLY 2-1.Disassembly Flow .4 2-2.Case .4 2-3.Front Panel Assy.5 2-4.KARAOKE Board/AC SELECT Board (Chilean and Peruvian Models) .5 2-5.MAIN Section .6 2-6.DIGITAL Board/MAIN Board.6 3.TEST MODE.7 4.DIAGRAMS 4-1.Block Diagram AUDIO INPUT Section .8 4-2.Block Diagram MAIN Section .9 4-3.Block Diagram KARAOKE Section . 10 4-4.Block Diagram PANEL Section . 11 4-5.Block Diagram AUDIO OUT, POWER SUPPLY Section . 12 4-6.Schematic Diagram MAIN Board (1/2) . 14 4-7.Schematic Diagram MAIN Board (2/2) . 15 4-8.Printed Wiring Board MAIN Board . 16 4-9.Schematic Diagram DIGITAL Board (1/3) . 17 4-10. Schematic Diagram DIGITAL Board (2/3) . 18 4-11. Schematic Diagram DIGITAL Board (3/3) . 19 4-12. Printed Wiring Board DIGITAL Board (Component Side) . 20 4-13. Printed Wiring Board DIGITAL Board (Conductor Side) . 21 4-14. Printed Wiring Boards MIC Section . 22 4-15. Schematic Diagram MIC Section . 23 4-16. Printed Wiring Boards DISPLAY Section . 24 4-17. Schematic Diagram DISPLAY Section . 25 4-18. Printed Wiring Board KARAOKE Board . 26 4-19. Schematic Diagram KARAOKE Board . 27 4-20. Printed Wiring Boards POWER SUPPLY Section . 28 4-21. Schematic Diagram POWER SUPPLY Section . 29 5.EXPLODED VIEWS 5-1.Overall Section . 39 5-2.Front Panel Section . 40 5-3.Chassis Section. 41 5-4.MAIN Section . 42 6.ELECTRICAL PARTS LIST. 43 UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. RadioFans.CN 收音机爱 好者资料库 3 STR-K5 SECTION 1 GENERAL This section is extracted from instruction manual. Receiver A.F.D. qg D.B.F.B. (button/indicator) 8 DISPLAY 5 Display 6 ECHO wh INPUT MODE q; INPUT SELECTOR qa IR (receptor) ql KARAOKE ON/OFF (button/ indicator) wj KEY CONTROL #/2 4 MASTER VOLUME 9 MEMORY/ENTER qj MIC 1 (jack) wf MIC 2 (jack) wd MIC 1 Tone knobs LOW, MID, HIGH 2 MIC 2 Tone knobs LOW, MID, HIGH 3 MIC 1 VOL wg MIC 2 VOL ws MOVIE qf MUSIC qd Music Tone knobs LOW, MID, HIGH 7 MUSIC VOLUME qs SCORE (button/indicator) wa TUNING /+ qk VOCAL SELECT (button/ indicator) w; 2CH qh ?/1 (power) 1 ALPHABETICAL ORDER A - L M - Z NUMBERS AND SYMBOLS 64231 w;waqaqsq;wdwfwh 589 wswgwjql 7 qdqfqgqhqjqk RadioFans.CN 收音机爱 好者资料库 STR-K5 4 Note: Follow the disassembly procedure in the numerical order given. 2-2.CASE This set can be disassembled in the order shown below. 2-1.DISASSEMBLY FLOW Note 1: The process described in can be performed in any order. Note 2: Without completing the process described in , the next process can not be performed. Note 3: Illustration of disassembly is omitted. SECTION 2 DISASSEMBLY 1two screws (BVTP3 8) 2two screws (case 3 TP2) 2two screws (case 3 TP2) 3case 2-2.CASE (Page 4) 2-5.MAIN SECTION (Page 6) 2-3.FRONT PANEL ASSY (Page 5) 2-4.KARAOKE BOARD/AC SELECT BOARD (Chilean and Peruvian Models) (Page 5) 2-6.DIGITAL BOARD/MAIN BOARD (Page 6) SET STR-K5 5 2-3.FRONT PANEL ASSY 2-4.KARAOKE BOARD/AC SELECT BOARD (Chilean and Peruvian Models) 2connector (CNP200) 1harness 3wire (flat type) (23 core) (CNS505) 4five screws (BVTP3 8) 5front panel assy 9connector (CN905) q;connector (CN910) qaAC SELECT board 8two screws (BVTP3 8) 4connector (CNP551) 1wire (flat type) (11 core) (CNS508) 5wire (flat type) (7 core) (CNS553) 6three screws (BVTP3 8) 2three screws (BVTP3 8) 3tuner (FM/AM) (TN1) 7KARAOKE board (Chilean and Peruvian models only) STR-K5 6 2-5.MAIN SECTION 2-6.DIGITAL BOARD/MAIN BOARD 5MAIN board 2connector (CNP504) 1connector (CNP503) 3two connectors (CNS502, CNS501) 4DIGITAL board 3screw (BVTP3 8) 6two screws (BVTP3 8) 5three screws (BVTP3 8) 4four screws (BVTP3 8) 1connector (CNP801) 7two screws (BV3) 9screw (BV3) 8two screws (BV3) 2connector (CNP901) 0main section 77 STR-K5 STR-K5 SECTION 3 TEST MODE FACTORY PRESET MODE All preset contents are reset to the default setting. Procedure: 1.While pressing the 2CH and MOVIE buttons, press theI/1button to turn on the main power. 2. The message “FACTORY” appears and the present contents are reset to the default values. FL CHECK MODE All fluorescent segments are tested. When this test is activated, all segments turn on at the same time, then each segment turns on one after another. Procedure: 1.While pressing the DISPLAY and A.F.D. buttons, press theI/1button to turn on the main power. 2. All segments and all LEDs turn on. 3.Press the INPUT SELECTOR button. 4.Half of segments and KARAOKE ON/OFF, SCORE LEDs turn on. 5.Press the INPUT SELECTOR button once again. 6. Others half of segments and VOCAL SELECT, D.B.F.B. LEDs turn on. 7. Press the INPUT SELECTOR button once again. 8. All segments and all LEDs turn off. VERSION MODE When this mode is used, the model, the destination and the software version number are displayed. Procedure: 1.While pressing the DISPLAY and TUNING + buttons, press theI/1button to turn on the main power. 2. The model, the destination and the software version number appear. KEY CHECK MODE This mode is used to check the key. Procedure: 1. While pressing the DISPLAY and 2CH buttons, press theI/1button to turn on the main power. 2. The message “REST 15” appears. 3. Every pressing of any button other than theI/1button counts down the buttons. The buttons which are already counted once are not counted again. 4. When all buttons are pressed, the message “REST 00” appears. SOUND FIELD CLEAR MODE The preset sound field is cleared when this mode is activated. Use this mode before returning the product to clients upon completion of repair. Procedure: 1. While pressing the 2CH button, press theI/1 button to turn on the main power. 2. The message “SF. CLR.” appears and initialization is performed. SPEAKER SIZE SELECTION MODE Either the normal speaker or micro satellite speaker can be selected. Procedure: 1.While depressing the DISPLAY and the TUNING - buttons simultaneously, press the I/1 button to turn on the main power. 2. Either the message “NORM. SP.” or “MICRO SP.” appears for a moment and select the desired speaker size. COMMAND MODE SELECTION MODE The command mode (AV1 or AV2) of the remote commander can be selected. Procedure: 1.While depressing the TUNING - button, press the I/1 button to turn on the main power. 2. Either the message “C.MODE.AV 1” or “C.MODE.AV 2” appears for a moment and select the desired mode. 88 STR-K5 STR-K5 4-1.BLOCK DIAGRAM AUDIO INPUT Section B D A C C-CH SR-CH R-CH SL-CH L-CH R-IN L-IN SW SEL C SEL SL SEL R-CH R-CH R-CH DIR FUNCTION SELECT IC400 AVCCDVDD +7V +3.3V +7V SEL SW MCU I/F SW OUT C OUT SL OUT L OUT Signal path : TUNER (FM/AM) : VIDEO (AUDIO) : CD (ANALOG) R-ch is omitted due to same as L-ch. 76 75 78 74 73 AUDIO INAUDIO IN LRLR VIDEO 1DVD AM TN1 FM/AM TUNER UNIT SYSTEM CONTROLLER IC1101 (1/5) SA-CD/CD LRLR J401J402 R-CH SLATCH 17 TUNER DATA 16 T.SERIAL CLK VOL DATA VOL CLK STEREO TUNED MUTE DO L-CH R-CH STEREO TUNED MUTING CE DO DATA CLOCK TU+10V 32 31 VIDEO 2 FM 75 COAXIAL ANTENNA 10 AUDIO INAUDIO IN 2627 24 25 14 49 48 40 41 SB-CH 33 21201916 7 6 9 8 3 2 5 4 32 +3.3V REGULATOR Q471 13 L SEL SECTION 4 DIAGRAMS (Page 9) (Page 12) (Page 9) (Page 10) 99 STR-K5 STR-K5 4-2.BLOCK DIAGRAM MAIN Section SDI1SD01 DOUT 1518 SDI230 GP8AUDIO24 XMCK 20 69 LRCKI115 BCKI117 KFSI0CKOUT1322 BCKI2BCK1429 LRCKI2LRCK1528 CS WE DATAO 23 SD02 24 SD03 25 SCKOUT 14 LRCKO 19 BCKO 20 X1502 13.9MHz X1301 12.288MHz MCLK19 MCLK2 12 CSO 44 WEO 45 68 108,107,105 -102,99, 98,80 - 77,75 - 72 24 - 27,42 - 44, 1 - 5,18 - 21 29 - 32,35 - 38, 16-13,10 - 7 112,110,109,97 - 92, 85-82,66 - 64 6 17 OEOEO 43 41 2 1133635 33 3432 299 37 67418 19 205 EXLOCK GP12 56BST ERROR 21 22 SYSCLK 16 BCK 14 LRCK 13 95969798 383736354717 INPUT DATA DEMODULATOR Pa,Pb DETECTIONLOCK DETECTION MICROPROCESSOR I/F C bit DETECTION 3459 16 DIGITAL COAXIAL DVD IN 1 DIGITAL OPTICAL SA-CD/CD IN OUT OPTICAL RECEIVER IC1352 IC1303 DIGITAL AUDIO I/F RECEIVER IC1301 J1301 23 WAVE SHAPER +1.8V VDDI +3.3V VDDE 5 +3.3V VDD L-INDIGITAL DECIM. FILTER A/D CONVERTER IC1401 DSP IC1501 SDRAM IC1502 SWITCH IC1503 8 GP12 ERROR 1 DATAO HACN XRST HDIN PM 392 BST_SEL HDOUT GP9 HACN HCS XRST HDIN PM HDOUT HCLK 6 CLK CE DI DO XSTATE CLK CE DI DO CKSEL1 93100 48 XMODE 94 CKSEL1 XMODE XSTATE 5 3 XOUT DIN2 DIN0 XIN D1301 D0-15A0-15 D0-15A0-15 SYSTEM CONTROLLER IC1101 (2/5) B E A MOD. HCLK BST HCS 3633 1215 PCM1602 MDO PCM1602 MDI PCM1602 MC PCM1602 ML PCM1602 RST MDO ML 35 13 MC 34 14 MDI 37 10 RST GP9 DATA3 L OUT R-CH VOUT5 VOUT6 VOUT1 VOUT2 VOUT3 VOUT4 47 2 9 101 AMP IC1403 45 46 38 SCKI 40 BCK LRCK41 LRCKO D/A CONVERTER IC1452 DAC DATA1 SL OUT R-CH 5 13 147 AMP IC1405 DAC DATA2 C OUT3121 SW OUT5117 AMP IC1404 DAC 1 2 1 L IN R-IN 5 R IN Signal path : TUNER (FM/AM) : VIDEO (AUDIO) : CD (DIGITAL) R-ch is omitted due to same as L-ch. (Page 8) (Page 8) (Page 10) 1010 STR-K5 STR-K5 4-3.BLOCK DIAGRAM KARAOKE Section Signal path : TUNER (FM/AM) R-ch is omitted due to same as L-ch. 51 TONE CONTROL IC2000 MIC AMP IC2004 MIC 1 AMP IC2001 RV2000 MIC 1 VOL RV2003 HIGH J2000 MIC 1 KARAOKE RV2002 MID RV2001 LOW 57 MIX AMP IC2350 (1/2) 57 AF AMP IC2102 57 AF AMP IC2101 L OUT 57 BUFFER AMP IC2351 31 31 MIX AMP IC2350 (2/2) +9V +K5V+15V RY2000 INVERTER IC2301 SYSTEM CONTROLLER IC1101 (3/5) 64 63 KARAOKE CONTROL IC2300 7 MIC AMP IC2003 IC2120 ECHO CONTROL ECHO RV2109 KARAOKE 16 18 20 14125 7513 210 TONE (MIC 1 TONE) TONE CONTROL IC2100 RV2103 HIGH RV2102 MID RV2101 LOW 16 18 20 1412TONE (MUSIC TONE) KARAOKE 51 MIC 2 AMP IC2002 RV2050 MIC 2 VOL RV2053 HIGH J2050 MIC 2 RV2052 MID RV2051 LOW 1 5 3 1 793TONE (MIC 2 TONE) 93 77 75 74 SEL R-CH WR STB CLK REQ DATA LOUT MIC IN L IN R IN ROUT SRAM K-OK R/W K-OK STB K-OK CLK K-OK REQ K-OK DATA INTERFACE
