Marantz-AV8003-pre-upd 电路图 维修手册.pdf
Page 1/10 Update AV8003 MAIN CPUs software procedure by FDT Update MAIN CPUs software to internal Flash-ROM. Update software for MAIN CPU NECESSARY EQUIPMENT The following items are required for updating. Windows PC (OS: Windows2000 or WindowsXP) with Serial port. RS-232C Dsub-9 pin cable (female to female/straight type) Flash Development Toolkit 4.01 (the rest is FDT) or latest version (fdtv401r00.exe or latest version) NOTE: The updating is not possible in FDT3.xx to the main microprocessor of AV8003. (e.g. FDT3.06) Use RS232C Dsub-9 pin cable (female to female/straight type) to connect PC and the RS-232C port in rear panel of the unit, when updating MAIN CPU A SOFTWARE (fdtv401r00.exe) DOWNLOADS AND INSTALLS PROCEDURE A-1 DOWNLOADS OF THE SOFTWARE Refer to page 14 of SR8001 service manual, and change to “fdtv401r00.exe” from “fdtv306r00.exe”. A-2 INSTALLS OF THE SOFTWARE Refer to page 33 of SR8001 service manual, and change to “fdtv401r00.exe” from “fdtv306r00.exe”. RadioFans.CN 收音机爱 好者资料库 Page 2/10 B UPDATE SOFTWARE B1-1 The writing software setup procedure 1. Launch the Flash Development Toolkit v4.01 (FDT) NOTE: Please refer to A SOFTWARE (fdtv401r00.exe) DOWNLOADS AND INSTALLS PROCEDURE, when you do not install FDT. 2. Click Start, Programs, Renesas, Flash Development Toolkit 4.01 and Flash Development Toolkit 4.01. 3. Check the Create a new project workspace, and click the OK. NOTE: It is needs setup for AV8003 When you have already setup, please advance to B1-2 Writing Procedure for MAIN CPU. RadioFans.CN 收音机爱 好者资料库 Page 3/10 4. AV8003_MAIN is inputted into the Workspace Name. (It is simultaneously inputted into Project Name.) Click the OK. 5. Input the Filter “M3087”. Then, selected ”M3087BFK “. And Click the Next. 6. Choose the Serial port number in the Select Port. And click the Next. RadioFans.CN 收音机爱 好者资料库 Page 4/10 7. Un-check the Use Default, and choose the 57600 in Recommended Speeds. Click the Next. 8. Check the Automatic in Protection. Check the Advanced in Messaging. Click the Finish. Page 5/10 B1-2 Writing Procedure for MAIN CPU 1. Connect the RS-232C on rear panel of the unit and the Serial Port of windows PC with RS-232C cable. 2. Launch the Flash Development Toolkit (FDT), When FDT is not launch. When FDT is already launch, please advance to step No.7. 3. Click Start, Programs, Renesas, Flash Development Toolkit 4.01 and Flash Development Toolkit 4.01. 4. Check the Browse to another project workspace, and click OK. 5. Choose AV8003_MAIN.AWS in AV8003_MAIN folder under workspase folder. And Click the Open. Page 6/10 6. Right button of mouse click on the AV8003_MAIN, and select the Add Files in a menu. 7. Browse and choose the av8003_rom_0 xxxxxx.mot, and click the Add. Update MAIN CPUs software to internal Flash-ROM 8. Connect RS-232C on the rear panel of the unit and Serial Port of windows PC with RS-232C cable. 9. Insert a thin rot to the hole near the REMOTE terminal and push the switch (SW10) inside to turn on the switch. Push switch (SW10) Hole of rear panel 10. Connect the mains cord into the unit. And press the POWER ON/OFF or STANDBY button for turn on the unit. NOTE: When the unit is into boot mode, STANDBY LED is not lights. Page 7/10 11. Click the Device in the menu bar and select the Connect to Device. 12. Click the Device in the menu bar and select the Erase FLASH Blocks. Page 8/10 13. Click the Select All and Erase. 14. Press right button of mouse on the av8003_rom_0 xxxxxx.mot, and select the Download File in a menu. Page 9/10 15. Software is written into the MAIN CPU. The writing of software takes about 2 minutes. 16. Click the Device in the menu bar and select the Disconnect. Page 10/10 17. Check the Do Noting and click the OK 18. Click the File and select the Exit in menu. 19. Press the POWER ON/OFF button for turn off the unit. (Except U1B) 20. Disconnect the mains cord and RS-232C cable from the unit. 21. Insert a thin rot to the hole and push the switch inside to turn off the switch.
