Pioneer-F208RDS-tun-sm电路图 维修手册.pdf

ORDER NO. PIONEER ELECTRONIC CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER ELECTRONIC (EUROPE) N.V. Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 ? ? ? ? ? ? PIONEER ELECTRONIC CORPORATION 1999 RRV2114 T ZZY MAY 1999 Printed in Japan FM/AM DIGITAL-SYNTHESIZER TUNER F-208RDS CONTENTS 1. SAFETY INFORMATION.2 2. EXPLODED VIEWS AND PARTS LIST .3 3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM 6 4. PCB CONNECTION DIAGRAM. 10 5. PCB PARTS LIST.14 6. ADJUSTMENT.15 7. GENERAL INFORMATION . 16 7.1 IC .16 8. PANEL FACILITIES AND SPECIFICATIONS. 17 THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S). Type Model F-208RDS Power Requirement HYXK/EWOAC220 - 230V HYXK/GROAC220 - 230V HVXKOAC230V Remarks STANDBY/ON RF ATT MPX CHARACTER BAND CLASSDIRECT TUNING TUNING MEMORY 12345 67890/10 FM/AM DIGITAL-SYNTHESIZER TUNERX<?B? ? MODE /SEARCH MODE DISPLAY MODE EON EON RadioFans.CN 收音机爱 好者资料库 F-208RDS 2 1. SAFETY INFORMATION This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician. WARNING This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause cancer, birth defects or other reproductive harm. Health to lower the frequency, turn counterclockwise. AM: For MW,frequency changes in 9 kHz steps. For LW,frequency changes in 1 kHz steps. FM: Frequency changes in 50kHz steps. In the Station Name input mode, PTY Search mode, the TUNING knob is used to select characters and program types. When presetting a station or selecting a preset station, you can also turn this knob to select a desired station number. 5? Operating Display Manual tuning mode Auto tuning mode Preset station tuning mode EON TA EON NEWS OFF 4? DISPLAY MODE button During FM reception, Use this to switch between display modes. Each time you press it, the display changes as follows. RT. Displays RTPS PS. Displays PS or Station name PTY FREQ . Displays frequency. STANDBY/ON RF ATT MPX CHARACTER BAND CLASSDIRECT TUNING TUNING MEMORY 12345 67890/10 FM/AM DIGITAL-SYNTHESIZER TUNERX<?B? ? MODE /SEARCH MODE DISPLAY MODE EON EON 1234 -?=! 567890 F-208RDS 18 DISPLAY 4? Frequency and character display section Band and frequency data is displayed. During FM reception, the display changes as follows each time the DISPLAY MODE button is pressed. RT. Displays RTPS PS . Displays PS or Station name PTY FREQ . Displays frequency. 1? EON(TA/NEWS) indicator Lights when EON mode is ON. Lights during EON Standby. Flashes during EON reception. 2? MEMORY indicator Lights when presetting stations. 3? AUTO indicator Lights during auto tuning mode. =? MPX (multiplex) MODE button Mode changes as follows each time this button is pressed. This button does not affect AM reception. AUTO: “AUTO”is not displayed. Normally leave in this mode for reception. When a stereo FM broadcast is received, it will be automatically reproduced in stereo sound and the STEREO indicator lights up. 5? RF ATT indicator Stays lit while RF ATT button is on. 6? RDS indicator Lights when an RDS broadcast is received. 0? MONO indicator Stays lit while MPX MODE button is set to MONO. 8? STEREO indicator Lights up when a stereo broadcast is received (the indicator does not light when the MPX MODE button is set to MONO). 9? TUNED indicator Lights when a broadcast is received. ? BAND button The button is used to select either FM or AM reception. The bands change alternately as follows, each time this button is pressed. !? STATION CALL buttons Use these buttons to preset stations and to receive the already preset stations. These are also used when performing direct access tuning. -? RF ATT button Set this button to on when receiving strong FM signals (nearby stations) to reduce sound distortion (RF ATT indicator lights). Normally, this button should be set to off. This button does not affect AM reception. NOTE: This buttons status is preset for each station in station memory. MONO: MONO indicator lights up. To receive stereo broadcasts in monaural. If there is too much noise during stereo reception of a weak signal, you can reduce the level of noise by switching to MONO. NOTES: This buttons status is preset for each station in station memory. When the signal level is too weak for reception, sound output is automatically muted. If sound is muted when the selected mode is AUTO, switching to MONO lets you hear the broadcast. LW reception MW reception FM reception AUTO MONO 1 23 756 9 8 4 AUTO MEMORY RF ATT R D S STEREO MONO TUNED EON TA NEWS F-208RDS 19 8.2 SPECIFICATIONS FM Tuner Section Frequency Range .87.5 MHz to 108 MHz Usable Sensitivity NORMAL .Mono: 14.2 dBf, IHF(1.4 V / 75 ). 50 dB Quieting Sensitivity NORMAL .Mono: 22.2 dBf, IHF (3.5 V / 75 ) Stereo: 38.6 dBf, IHF (23.3 V / 75 ) Sensitivity (DIN) NORMAL . Mono: 1.0 V / 75 ) Stereo:50 V / 75 ) Signal-to-Noise Ratio . Mono: 76 dB (at 85 dBf) Stereo: 73 dB (at 85 dBf) Signal-to-Noise Ratio (DIN) . Mono: 64 dB Stereo: 60 dB Distortion .Mono: 0.4 % (1 kHz) Stereo: 1.0 % (1 kHz) Alternate Channel Selectivity . 70 dB (400 kHz) Stereo Separation . 40 dB (1 kHz) Frequency Response . 1 dB (30 Hz to 15 kHz) Image Response Ratio . 80 dB IF Response Ratio . 90 dB Antenna Input. 75 unbalanced AM (MW) Tuner Section Frequency Range . 531 kHz to 1,602 kHz (Step 9 kHz) Sensitivity (IHF, Loop antenna). 350 V / m Selectivity . 33 dB(10 kHz) Signal-to-Noise Ratio . 51 dB Image Response Ratio . 35 dB IF Response Ratio . 51 dB Antenna. Loop Antenna AM (LW) Tuner Section Frequency Range . 153 kHz to 281 kHz Sensitivity (IHF, Loop antenna). 1,000 V / m Selectivity . 30 dB Signal-to-Noise Ratio . 51 dB Image Response Ratio . 30 dB IF Response Ratio . 51 dB Antenna. Loop Antenna Audio Section Output (Level/Impedance) FM (100 % MOD) . 1.0 V / 1k AM (30 % MOD) . 224 mV / 1k Miscellaneous Power Requirements . AC 230 Volts, 50 / 60 Hz Power Consumption. 10 W Power Consumption in standby mode . 1 W Dimensions . 420 (W) x 78 (H) x 287 (D) mm Weight (without package) .2.7 kg Furnished Parts FM T-type antenna. 1 AM Loop antenna. 1 Audio cord . 1 Control cord . 1 Operating Instructions . 1 Warranty card . 1 NOTE: Specifications and design are subject to possible modifications without notice, due to improvements. FM T-type antenna (ADH7009) AM loop antenna (ATB7009) Audio cord (PDE1290) L=1m Control cord (PDE1095) L=1m (Red) (White) Accessories (black)