United-Motors-Service-Delco-984817 电路原理图.pdf

收音机爱 好者资料库 RadioFans.CN MANUAL OF I9S3 MOST-OFTEN-NEEDED RADIO DIAGRAMS _ _ Alignment procedure for models listed UNITED MOTORS SERVICE below. For circuit diagrams and align- division of general motors corporation ment points see corresponding models as shown on pages 141 to 145. Volume Control Position-Maximum Volume Tone Control Position - Treble Generator Output _ Minimum for Readable Indication BUICK 981320 Steps Series Condenser or Dummy Antenna Connect Signal Generator to Signal Generator Frequency Tune Receiver to Adjust in Sequence For Max. Output 1 0.1 Mfd. 6BE6 Grid (Pin #7) 262 KC High Frequency Stop A, B, C, D 2 0.000082 Mfd. Antenna Connector 1615 KC High Frequency Stop *E, F, G 3 0.000082 Mfd. Antenna Connector 1000 KC Signal Generator Signal J, K 4 0.000082 Mfd. Antenna Connector 1615 KC High Frequency Stop F, G 5 0.000082 Mfd. Antenna Connector 1000 KC Signal Generator Signal L* BUXCK 98I32I 1 0.1 Mfd. 12BE6 Grid (Pin #7) 262 KC High Frequency Stop A, B, C, D 2 0.000082 Mfd. Antenna Connector 1615 KC High Frequency Stop *E, F, G 3 0.000082 Mfd. Antenna Connector 1000 KC Signal Generator Signal J, K 4 0.000082 Mfd. Antenna Connector 1615 KC High Frequency Stop F, G 5 0.000082 Mfd. Antenna Connector 1000 KC Signal Generator Signal L* OLDSMOBILE MODEL 982990 1 0.1 Mfd. 12BE6 Grid (Pin # 7) 260 KC High Frequency Stop A, B, C, D 2 0.000068 Mfd. Antenna Connector 1615 KC High Frequency Stop *E, F, G 3 0.000068 Mfd. Antenna Connector 1000 KC Signal Generator Signal J. K 4 0.000068 Mfd. Antenna Connector 1615 KC High Frequency Stop F, G 5 0.000068 Mfd. Antenna Connector 1000 KC Signal Generator Signal *L OLDSMOBILE MODEL 983004 1 0.1 mfd. 12BE6 Grid (Pin 7) 260 KC High Frequency Stop A, B, C (Max.) 2 0.1 mfd. 12BE6 Grid (Pin 7) 260 KC High Frequency Stop D (Min.) 3 0.000068 mfd. Antenna Connector 1615 KC High Frequency Stop *E, F, G (Max.) 4 0.000068 mfd. Antenna Connector 600 KC Signal Generator Signal J, K (Max.) 5 0.000068 mfd. Antenna Connector 1615 KC Signal Generator Signal F, G (Max.) 6 0.000068 mfd. Antenna Connector 1000 KC Signal Generator Signal *L MODEL 984817 i j 0.1 Mfd. 6BE6 Grid (Pin #7) 260 KC High Freq. Stop A, B, C, D 2 0.000068 Mfd. i Antenna Connector 1615 KC High Freq. Stop *E, F, G 3 0.000068 Mfd. Antenna Connector 1000 KC Signal Gen. Signal J, K 4 0.000068 Mfd. 1 Antenna Connector 1615 KC High Freq. Stop F, G 5 0.000068 Mfd. i Antenna Connector 1000 KC Signal Gen. Signal L* Before making this adjustment check the mechanical setting of the oscillator core H.” The slotted end of core should be IIS from the mounting end of the coil form. (This measurement is readily made by inserting a suitable plug in the mounting end of the coil form.) If adjustment is necessary, first dissolve the glyptal seal on the studs. Core ad justment should be made with an insulated screwdriver and core studs should be re-sealed in place with glyptal or household cement after alignment. *“L” is the pointer adjustment screw which is on the pointer connecting link (see tuner drawing) and should be adjust ed so the pointer reads 1000 KC. (On first “0” of “100.”) With the radio installed and the car antenna plugged in adjust the antenna trimmer “G” for maximum volume with the radio tuned to a weak station between 600 ana 1000 KC. (See sticker on case.) it To tune to high frequency, put a 0.070” feeler gauge (or bare #13 wire) in slot against the high frequency stop. (See tuner pictures). Depress station selector bar and allow the planetary arm to run against the feeler gauge. Turn * the radio off and men on. 收音机爱 好者资料库 RadioFans.CN