Philips-DS-9800-Service-Manual电路原理图.pdf

Published by Sophie-KM 1148 AVM Printed in the NetherlandsDS9800W/10/37/93Subject to modi cation ENDocking Speaker SystemContents Page Contents Page©Copyright 2011 Philips Consumer Electronics B.V. Eindhoven, The Netherlands.All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips.Version 1.11 Technical Specification and Connection Facilities2 Laser Beam Safety Precautions. 2-13 Important Safety Precautions . 3-1 to 3-24 Safety Check After Servicing . 4-16 Standard Notes For Servicing,Lead Free Requirements+A1:2003, +A2:2006, EN55020:2007 IT-functions: EN55022:2006,+A1:2007, EN55024:1998, +A1:2001, +A2:2003 WiFi-function: ETSI EN 300 328 (V1.7.1.), ETSI EN 301 489-1 (V1.8.1.) +A1:2001; +A2:2005 or alternatively EN61000-3-3:2008 /97 (/55) Audio functions: CISPR-13:2006 (or alternatively CISPR-13:2009), CISPR-20:2005; IT-functions: CISPR-22;2008, CISPR-24:1997; +A1:2001, +A2:2002; IEC 62311:2007 Generic functions: IEC 61000-3-2:2005,+A1:2008,+A2:2009 or alternatively IEC 61000-3-2:2009, IEC 61000-3-3:2008 /37 FCC-15.247 (Part B, C), OET Bulletin 65, Edition 97-01 Table 1; RSS-210 Issue 7 10 93Region Europe ChinaModel DS9800WTechnical Specification and Connection Facilities 1-4ESD Requirements(TBC) The product shall withstand electro static discharges on all user accessible parts of the product. Reference: IEC61000-4-2. For contact discharges: Level General (kV) USA (kV) Requirement 1 0-2 0-3 No deviations allowed. 2 >2-4 >3-4 Short perceptible deviations allowed 3 >4-5 >4-5 Normal recallable functions function changes allowed. 4 >5-7 >5-7 Control recallable functions function changes allowed. 5 - >7-8 No loss of stored data allowed. For air discharge: Level General (kV) USA (kV) Requirement 1 0-4 0-6 No deviations allowed. 2 >4-8 >6-8 Short perceptible deviations allowed. 3 >8-10 >8-10 Normal recallable functions function changes allowed. 4 >10-15 >10-15 Control recallable functions function changes allowed. 5 - >15-18 No loss of stored data allowed. General requirement: 1. 10 arcs for positive and negative polarity for unit “on” and “off” for 1kV incremental steps. 2. Component or mechanical damage is not allowed. No loss of fixed stored data (stored in EEPROMs). 3. Hang-ups and malfunctions are allowed, as long as the customer can “recover” from the hang-up by pressing the Standby or ON/OFF button of the set. 4. Failures that disappear only by unplugging the AC mains cord and/or power sources are not acceptable. Environmental Condition The environmental condition requirements and test method is according to UAN-D1590. Ambient temperature : max. 40 ° C - all climates Apparatus acc. to spec. : +5 to + 35 ° C Vibration test (acc. IEC 60 068/2/6) : operational vibration test to be proceeded in operating position of the set. Technical Specification and Connection Facilities 1-53. Technical Specifications Power Supply 3.1.1 Type and versions 3.1.1.1 SMPS for main unit Build-inSMPS will be used for all models and stroke versions. All using figure '8' socket, will cater for all versions: Versions Region/Country SMPS Detachable mains cords nip-3 )50/( KU Rin 22k cbt yalpriA enohPiA1.2 tnerruc gnigrahc gnikcoD 5V voltage power supplyW0089SD Output Power(*4) At THD=10%, 1kHz sinewave 50W± 1dB ( At Cold Condition with 10% THDOutput Power with limitation(shipment sample) 36W± 1dB ( At Cold Condition with 10% THDFrequency Response(± 3dB) 30Hz-20kHZ Loudspeaker(Boxes): Separable speaker box Refer to package document of Speaker Box Assy Speaker driver Impedance: Right/Left: 8 30 Hz 20kHz(-1db)(tbc) :refoowbuS REMARKS: Electrical Parameters are to be measured at Speaker Terminals across rated impedance Load(8ohm) with Rated Input Signal in CD Mode setting in DBB/Loudness Off and Pre-eq at Flat unless specified otherwise. *1) Add 10dB to the measured SNR for the final result as a -10dB reference signal is used (IEC (A) weighted Vol.max with -10dB) *2) standard output - 1W output with 1kHz sinewave *3) SNR value is defined at Airplay mode, at MP3-link mode are worse a little.(SNR ROP(A-Weighted): limit 85dBA, 1W output (A-Weighted): limit 78dBA) *4) Test mode : press RESET and WPS key 5s, the set go to factory mode. Many electrical parameter should measured at factory mode. Laser Beam Safety PrecautionsThis Blu-Ray player uses a pickup that emits a laser beam.The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keepyour eyes at least 30 cm away from the pickup lens when the diode is turned on. Do not look directly at the laserbeam.CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result inhazardous radiation exposure.Location: Inside Top of Blu-Ray mechanism.Do not look directly at the laser beam comingfrom the pickup or allow it to strike against yourskin.Drive Mechanism AssemblyLaser Beam RadiationLaser PickupTurntable2-1Electronics N.V. bears no responsibilityfor improper wall mounting that results inaccident, injury or damage.For speakers with stands, use only thesupplied stands. Secure the stands tothe speakers tightly. Place the assembledstands on flat, level surfaces that cansupport the combined weight of thespeaker and stand.Never place the product or any objectson power cords or on other electricalequipment.If the product is transported intemperatures below 5°C, unpack theproduct and wait until its temperaturematches room temperature beforeconnecting it to the power outlet.Visible and invisible laser radiation whenopen. Avoid exposure to beam.Do not touch the disc optical lens insidethe disc compartment.Risk of overheating!Never install this product in a confinedspace. Always leave a space of at leastfour inches around the product forventilation. Ensure curtains or otherobjects never cover the ventilation slotson the product.Risk of contamination!Do not mix batteries (old and new orcarbon and alkaline, etc.).Remove batteries if they are exhaustedor if the remote control is not to be usedfor a long time.Batteries contain chemical substances,they should be disposed of properly.Product careDo not insert any objects other than discsinto the disc compartment.Do not insert warped or cracked discsinto the disc compartment.Remove discs from the disc compartmentifyouarenotusingtheproductforanextended period of time.Only use microfiber cloth to clean theproduct.ImportantImportant Safety PrecautionsRead and understand all instructions before you useyour home theater. If damage is caused by failure to follow instructions, the warranty does not apply. SafetyRiskof electricshock or fire!Never expose the product andaccessories to rain or water. Never placeliquid containers, such as vases, near theproduct. If liquids are spilt on or into theproduct, disconnect it from the poweroutlet immediately. Contact PhilipsConsumer Care to have the productchecked before use.Never place the product and accessoriesnear naked ames or other heat sources,including direct sunlight.Never insert objects into the ventilationslots or other openings on the product.Where the mains plug or an appliancecoupler is used as the disconnect device,the disconnect device shall remain readilyoperable.Disconnect the product from the poweroutlet before lightning storms.When you disconnect the power cord,always pull the plug, never the cable.Riskof short circuit or re!Before you connect the product to thepoweroutlet,ensurethatthepowervoltage matches the value printed on theback or bottom of the product. Neverconnecttheproducttothepoweroutletif the voltage is different.Risk of injury or damage to the home theater!For wall-mountable products, use onlythe supplied wall mount bracket. Securethe wall mount to a wall that can supportthe combined weight of the productand the wall mount. Koninklijke Philips3-1Caution: These servicing instructions are for use by qualified service personnel only.To reduce the risk of electric shock do not perform any servicing other than that contained in the operatinginstructions unless you are qualified to do so.