Philips-DVD-755-VR-Service-Manual电路原理图.pdf
Published by MW 0365 Service PaCE Printed in the Netherlands Subject to modification EN 3122 785 13520©Copyright 2003 Philips Consumer Electronics B.V. Eindhoven, The Netherlands. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips.DVD-VCR Player DVD755VRDVD755VR /00DVD755VR /02DVD755VR /05DVD755VR /14SECTION 1 SUMMARY 1-1PRODUCT SAFETY SERVICING GUIDELINES FOR VIDEO PRODUCTS 1-3SERVICING PRECAUTIONS 1-4SERVICE INFORMATION FOR EEPROM IC SETTING 1-5SPECIFICATIONS 1-6SECTION 2 CABINET CONNECT A 1500 OHM 10 WATT RESIS-TOR, PARALLELED BY A .15 MFD. 150.V A.C TYPE CAPACITORBETWEEN A KNOWN GOOD EARTH GROUND (WATER PIPE, CON-DUIT, ETC.) AND THE EXPOSED METALLIC PARTS, ONE AT A TIME.MEASURE THE A.C. VOLTAGE ACROSS THE COMBINATION OF 1500 OHM RESISTOR AND .15 MFD CAPACITOR. REVERSE THE A.C. PLUGAND REPEAT A.C. VOLTAGE MEASUREMENTS FOR EACH EXPOSED METALLIC PART. VOLTAGE MEASURED MUST NOT EXCEED 75VOLTS R.M.S. THIS CORRESPONDS TO 0.5 MILLIAMP A.C ANYVALUE EXCEEDING THIS LIMIT CONSTITUTES A POTENTIAL SHOCKHAZARD AND MUST BE CORRECTED IMMEDIATELY.SUBJECT: GRAPHIC SYMBOLSTHE LIGHTNING FLASH WITH APROWHEAD SYMBOL. WITHINAN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THESERVICE PERSONNEL TO THE PRESENCE OF UNINSULATED“DANGEROUS VOLTAGE” THAT MAY BE OF SUFFICIENT MAG-NITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK.THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIAN-GLE IS INTENDED TO ALERT THE SERVICE PERSONNEL TOTHE PRESENCE OF IMPORTANT SAFETY INFORMATION INSERVICE LITERATURE.SUBJECT : X-RADIATION1. BE SURE PROCEDURES AND INSTRUCTIONS TO ALL SERVICE PER-SONNEL COVER THE SUBJECT OF X-RADIATION. THE ONLY POTEN-TIAL SOURCE OF X-RAYS IN CURRENT T.V. RECEIVERS IS THE PIC-TURE TUBE. HOWEVER, THIS TUBE DOES NOT EMIT X-RAYS WHENTHE HIGH VOLTAGE IS AT THE FACTORY SPECIFIED LEVEL. THE PROPER VALUE IS GIVEN IN THE APPLICABLE SCHEMATIC. OPERA-TION AT HIGHER VOLTAGES MAY CAUSE A FAILURE OF THE PIC-TURE TUBE OR HIGH VOLTAGE SUPPLY AND, UNDER CERTAIN CIR-CUMSTANCES, MAY PRODUCE RADIATION IN EXCESS OF DESIR-ABLE LEVELS.2. ONLY FACTORY SPECIFIED C.R.T. ANODE CONNECTORS MUST BEUSED. DEGAUSSING SHIELDS ALSO SERVE AS X-RAY SHIELD INCOLOR SETS, ALWAYS RE-INSTALL THEM.3. IT IS ESSNTIAL THAT SERVICE PERSONNEL HAVE AVAILABLE ANACCURATE AND RELIABLE HIGH VOLTAGE METER. THE CALIBRATION OF THE METER SHOULD BE CHECKED PERIODICALLYAGAINST A REFERENCE STANDARD, SUCH AS THE ONE AVAILABLEAT YOUR DISTRIBUTOR.4. WHEN THE HIGH VOLTAGE CIRCUITRY IS OPERATING PROPERLYTHERE IS NO POSSIBILITY OF AN X-RADIATION PROBLEM. EVERYTIME A COLOR CHASSIS IS SERVICED. THE BRIGHTNESS SHOULDBE RUN UP AND DOWN WHILE MONITORING THE HIGH VOLTAGEWITH A METER TO BE CERTAIN THAT THE HIGH VOLTAGE DOESNOT EXCEED THE SPECIFIED VALUE AND THAT IT IS REGULATINGCORRECTLY, WE SUGGEST THAT YOU AND YOUR SERVICE ORGA-NIZATION REVIEW TEST PROCEDURES SO THAT VOLTAGE REGU-LATION IS ALWAYS CHECKED AS A STANDARD SERVICING PROCE-DURE. AND THAT THE HIGH VOLTAGE READING BE RECORDER ONEACH CUSTOMERS INVOICE.5. WHEN TROUBLESHOOTING AND MAKING TEST MEASUREMENTS INA PRODUCT WITH A PROBLEM OF EXCESSIVE HIGH VOLTAGE,AVOID BEING UNNECESSARILY CLOSE TO THE PICTURE TUBE ANDTHE HIGH VOLTAGE SUPPLY. DO NOT OPERATE THE PRODUCTLONGER THAN IS NECESSARY TO LOCATE THE CAUSE OF EXCESSIVE VOLTAGE.6. REFER TO HV. B+ AND SHUTDOWN ADJUSTMENT PROCEDURES DESCRIBED IN THE APPROPRIATE SCHEMATIC AND DIAGRAMS(WHERE USED).SUBJECT: IMPLOSION1. ALL DIRECT VIEWED PICTURE TUBES ARE EQUIPPED WITH AN INTEGRAL IMPLOSION PROTECTION SYSTEM, BUT CARE SHOULD BETAKEN TO AVOID DAMAGE DURING INSTALLATION, AVOIDSCRATCHING THE TUBE. IF SCRATCHED REPLACE IT.2. USE ONLY RECOMMENDED FACTORY REPLACEMENT TUBES.SUBJECT : TIPS ON PROPER INSTALLATION1. NEVER INSTALL ANY PRODUCT IN A CLOSED-IN RECESS, CUBBY-HOLE OR CLOSELY FITTING SHELF SPACE. OVER OR CLOSE TOHEAT DUCT, OR IN THE PATH OF HEATED AIR FLOW.2. AVOID CONDITIONS OF HIGH HUMIDITY SUCH AS: OUTDOOR PATIOINSTALLATIONS WHERE DEW IS A FACTOR, NEAR STEAM RADIA-TORS WHERE STEAM LEAKAGE IS A FACTOR, ETC.3. AVOID PALCEMENT WHERE DRAPERIES MAY OBSTRUCT REARVENTING. THE CUSTOMER SHOULD ALSO AVOID THE USE OF DEC-ORATIVE SCARVES OR OTHER COVERINGS WHICH MIGHTOBSTRUCT VENTILATION.4. WALL AND SHELF MOUNTED INSTALLATIONS USING A COMMER-CIAL MOUNTING KIT. MUST FOLLOW THE FACTORY APPROVED MOUNTING INSTRUCTIONS A PRODUCT MOUNTED TO A SHELF ORPLATFORM MUST RETAIN ITS ORIGINAL FEET (OR THE EQUIVALENTTHICKNESS IN SPACERS) TO PROVIDE ADEQUATE AIR FLOW ACROSS THE BOTTOM, BOLTS OR SCREWS USED FOR FASTENERSMUST NOT TOUCH ANY PARTS OR WIRING. PERFORM LEAKAGETEST ON CUSTOMIZED INSTALLATIONS.5. CAUTION CUSTOMERS AGAINST THE MOUNTING OF A PRODUCT ONSLOPING SHELF OR A TILTED POSITION, UNLESS THE PRODUCT ISPROPERLY SECURED.6. A PRODUCT ON A ROLL-ABOUT CART SHOULD BE STABLE ON ITSMOUNTING TO THE CART. CAUTION THE CUSTOMER ON THE HAZ-ARDS OF TRYING TO ROLL A CART WITH SMALL CASTERS ACROSSTHRESHOLDS OR DEEP PILE CARPETS.7. CAUTION CUSTOMERS AGAINST THE USE OF A CART OR STANDWHICH HAS NOT BEEN LISTED BY UNDERWRITERS LABORATORIES, INC. FOR USE WITH THEIR SPECIFIC MODEL OF TELEVISION RECEIVER OR GENERICALLY APPROVED FOR USE WITH T.V.S OFTHE SAME OR LARGER SCREEN SIZE.8. CAUTION CUSTOMERS AGAINST THE USE OF EXTENSION CORDS, EXPLAIN THAT A FOREST OF EXTENSIONS SPROUTING FROM A SIN-GLE OUTLET CAN LEAD TO DISASTROUS CONSEQUENCES TOHOME AND FAMILY.PRODUCT SAFETY SERVICING GUIDELINES FOR VIDEO PRODUCTSA.C. VOLTMETERGOOD EARTH GROUNDSUCH AS THE WATERPIPE. CONDUIT. ETCPLACE THIS PROBEON EACH EXPOSEDMETAL PART1-4SERVICING PRECAUTIONSCAUTION : Before servicing the VCR+DVD covered by thisservice data and its supplements and addends, read and fol-low the SAFETY PRECAUTIONS. NOTE : if unforeseen cir-cumstances create conflict between the following servicingprecautions and any of the safety precautions in this publi-cations, always follow the safety precautions.Remembers Safety First:General Servicing Precautions1. Always unplug the VCR+DVD AC power cord from the ACpower source before:(1) Removing or reinstalling any component, circuit board, module, or any other assembly.(2) Disconnection or reconnecting any internal electricalplug or other electrical connection.(3) Connecting a test substitute in parallel with an elec-trolytic capacitor.Caution : A wrong part substitution or incorrect polarity installation of electrolytic capacitors may resultin an explosion hazard.2. Do not spray chemicals on or near this VCR+DVD or anyof its assemblies.3. Unless specified otherwise in this service data, cleanelectrical contacts by applying an appropriate contact cleaning solution to the contacts with a pipe cleaner,cotton-tipped swab, or comparable soft applicator.Unless specified otherwise in this service data, lubricationof contacts is not required.4. Do not defeat any plug/socket B+ voltage interlocks withwhitch instruments covered by this service manual mightbe equipped.5. Do not apply AC power to this VCR+DVD and/or any of itselectrical assemblies unless all solid-state device heatsinks are cerrectly installed.6. Always connect test instrument ground lead to theappropriate ground before connection the test instrumentpositive lead. Always remove the test instrument ground lead last.Insulation Checking ProcedureDisconnect the attachment plug from the AC outlet and turnthe power on. Connect an insulation resistance meter(500V)to the blades of the attachment plug. The insulation resis-tance between each blade of the attachment plug and acces-sible conductive parts (Note 1) should be more than 1M-ohm.Note 1 : Accessible Conductive Parts including Metal pan-els, Input terminals, Earphone jacks, etc.Electrostatically Sensitive (ES) DevicesSome semiconductor (solid state) devices can be damagedeasily by static electricity. Such components commonly arecalled Electrostatically Sensitive (ES) Devices. Examples oftypical ES devices are integrated circuits and some fieldeffect transistors and semiconductor chip components.The following techniques should be used to help reduce theincidence of component damage caused by static electricity.1. Immediately before handling any semiconductor compo-nent or semiconductor-equipped assembly, drain off anyelectrostatic charge on your body by touching a knownearth ground. Alternatively, obtain and wear a commer-cially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test.2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.3. Use only a grouned-tip soldering iron to solder or unsolderES devices.4. Use only an anti-static solder removal device. Somesolder removal devices not classified a “anti-static” cangenerate electrical charges sufficient to damage ES devices.5. Do not use freon-propelled chemicals. These cangenerate electrical charge sufficient to damage ESdevices.6. Do not remove a replacement ES device from its protective package until immediately before you are ready toinstall it. (Most replacement ES devices are packaged withleads electrically shorted together by conductive foam,aluminum foil, or comparable conductive material).7. Immediately before removing the protective material fromthe leads of a replacement ES device, touch the protectivematerial to the chassis or circuit assembly into which thedevice will be installed.Caution : Be sure no power is applied to the chassis orcircuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Normally harmless motion such as the brushing together of your clothes fabric or the liftingof your foot from a carpeted floor can generate static elec-tricity sufficient to damage an ES device.)1-5SERVICE INFORMATION FOR EEPROM IC SETTINGMODEL NAME HEX BINARYDVD755VR/00 OPT1 7C 00000000OPT2 63 00000000OPT3 89 00000000OPT4 F1 00000000OPT5 31 00000000OPT6 48 00000000DVD755VR/02 OPT1 7C 00000000OPT2 63 00000000OPT3 09 00000000OPT4 F0 00000000OPT5 62 00000000OPT6 40 00000000DVD755VR/05 OPT1 3C 00000000OPT2 63 00000000OPT3 89 00000000OPT4 F1 00000000OPT5 31 00000000OPT6 48 00000000DVD755VR/14 OPT1 3C 00000000OPT2 6A 00000000OPT3 89 00000000OPT4 F7 00000000OPT5 00 00000000OPT6 50 00000000WR : OK I : EXIT MOVE : F GEDIT : DE1. DETECT NEW EEPROM (OPTION EDITSCREEN)- Eeprom EDIT screen automatically appears ifreplacing Eeprom.- Setup option data using the cursor Up/Down keyof a remote control.(Setup upon BOM depending on OPT1OPT6model) Since an initial remote control is set to LG for LGmodel, appropriately set option data using thecursor Up/Down key. For PHILIPS model, change a remocon key byusing following JIG key.PHILIPS MODEL : FRONT FF + FRONT RECKEY(LG/PHILIPS CODE)2. EEPROM WRITED COMPLETE SCREEN- Writes data on EEPROM by using REMOCON“OK“. - If completing the option data screen with a menukey, Powering Off is automatically done and theoption edit screen is arranged.3. PG ADJUST1) Payback the SP standard tape2) Press the “1” key on the Remote controller andthe “PLAY” key on the Front Panel at the sametime, then it goes into Tracking initial mode. 3) Repeat the above step(No.2), then it finishesthe PG adjusting automatically.4) Stop the playback, then it goes out to PGadjusting mode after mony the PG data. 4. EEPROM INITIAL- SETUP is displayed in the field if pressing theFRONT REC KEY with the remocon number“CLEAR“ key pressed in the status of no tape.- AUTO SEARCH is done since the initial screenof ACMS is serviced if powering On.- Check basic operation (PLAY/RECORD.)EEPROM option code No. setting EEPROM option code No. setting procedureNAME HEX BINARYOPT1 00 00000000OPT2 00 00000000OPT3 00 00000000OPT4 00 00000000OPT5 00 00000000OPT6 00 00000000WR : OK I : EXIT MOVE : F GEDIT : DEMASKROM : R00EEPROM : R00 LG CODE1-6SPECIFICATIONSDVD PARTPower supply AC 220230V, 50HzPower consumtion 23WMass 5.4kg External dimensions 430 x 97.5 x 360 (W x H x D)Signal system PAL 625/50, NTSC 525/60Laser Semiconductor laser, wavelength 650nmFrequency range (digital audio) 4 Hz to 20 kHzSignal-to-noise ratio (digital audio) More than 100 dB (EIAJ)Audio dynamic range (digital audio) More than 95 dB (EIAJ)Harmonic distortion(digital audio) 0.008%Wow and flutter Below measurable level (less than +0.001%(W.PEAK) (EIAJ)Operations Temperature : 5C(41F) to 35C(95F),Operation status : HorizontalOUTPUTSVideo outputs 1.0V(p-p), 75, negative sync., RCA jack x 1/SCART(TO TV)S video outputs (Y)1.0V(p-p), 75, negative sync.,Mini DIN 4-pin x 1(C)0.3V(p-p), 75Component video output (Y) 1.0 V (p-p), 75 , negative sync., RCA jack x 1(Pb)/(Pr) 0.7 V (p-p), 75 Audio output(digital audio) 0.5V(p-p), 75, RCA jack X 1/SCART(TO TV)Audio output(optical audio) Optical connector x 1Audio output(analog audio) 2.0Vrms (1kHz, 0dB), 330, RCA jack (L, R) x 1/SCART(TO TV)VHS PARTVideo Head System Double azimuth 4 heads, helical scanningTape format Tape width 12.7 mm (0.5 inch)Timer 24 hours display type*Designs and specifications are subject to change without notice.*Weight and dimensions shown are approximate.Directions for Use
