Sony-STR-DA4300ES-Service-Manual电路原理图.pdf

SERVICE MANUAL AUDIO POWER SPECIFICATIONS (US model) POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 8 ohm loads, both channels driven, from 20 20,000 Hz; rated 100 watts per channel minimum RMS power, with no more than 0.09% total harmonic distortion from 250 milliwatts to rated output. Amplifier section POWER OUTPUT Rated Power Output at Stereo Mode1) 2) (8 ohms 20 Hz 20 kHz, THD 0 09%): 100W + 100W Reference Power Output at Stereo Mode (4 ohms 20 Hz 20 kHz, THD 0 15%): 85W + 85W Reference Power Output (8 ohms 1 kHz, THD 0 7%) FRONT2): 110W + 110W CENTER2): 110 W SURROUND2): 110W + 110W SUR BACK2): 110W + 110W Reference Power Output (4 ohms 1 kHz, THD 0 7%) FRONT2): 100W + 100W CENTER2): 100 W SURROUND2): 100W + 100W SUR BACK2): 100W + 100W 1)Depending on the sound field settings and the source, there may be no sound output 2)Measured under the following conditions: Power requirements: 120 V AC, 60 Hz Frequency response Inputs (Analog) Inputs (Digital) Outputs EQUALIZER FM tuner section Tuning range87.5 108.0 MHz Antenna (aerial)FM wire antenna (aerial) Antenna (aerial) terminals 75 ohms, unbalanced PHONORIAA equalization curve 0 5 dB MULTI CHANNEL INPUT, SA-CD/CD, MD/TAPE, DVD/BD, TV, SAT/CATV, VIDEO 1/2/3 10 Hz 100 kHz 3 dB PHONOSensitivity: 2 5 mV Impedance: 50 kohms S/N: 90dB (A, 20 kHz LPF) MULTI CHANNEL INPUT, SA-CD/CD, MD/TAPE, DVD/BD, TV, SAT/CATV, VIDEO 1/2/3 Sensitivity: 150 mV Impedance: 50 kohms S/N: 100 dB (A, 20 kHz LPF) DVD/BD,VIDEO 2, SA-CD/CD (Coaxial) Impedance: 75 ohms S/N: 96 dB (A, 20 kHz LPF) VIDEO 1, VIDEO 3, SAT/CATV, TV, MD/ TAPE (Optical) S/N: 96 dB (A, 20 kHz LPF) MD/TAPE (REC OUT), VIDEO 1 (AUDIO OUT) Voltage:150 mV Impedance: 1 kohm FRONT L/R, CENTER, SURROUND L/R, SUR BACK L/R, SUB WOOFER Voltage: 2 V Impedance: 1 kohm Gain levels10 dB, 1 dB step MULTI CHANNEL AV RECEIVER SPECIFICATIONS Ver. 1.1 2007.10 Continued on next page 9-887-785-02 2007J05-1 2007.10 Sony Corporation Home Audio Division Published by Sony Techno Create Corporation This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS* Digital Surround System *Manufactured under license from Dolby Laboratories Dolby, Pro Logic, Surround EX, and the double-D symbol are trademarks of Dolby Laboratories * Manufactured under license from DTS, Inc “DTS”, “DTS-ES” and “Neo:6” are registered trademarks of DTS, Inc and “DTS-HD Master Audio”, “DTS-HD High Resolution Audio” and “DTS 96/24” are trademarks of DTS, Inc STR-DA4300ES US Model Canadian Model RadioFans.CN 收音机爱 好者资料库 2 STR-DA4300ES Video section Inputs/Outputs Video:1 Vp-p, 75 ohms COMPONENT VIDEO: Y: 1 Vp-p, 75 ohms PB/CB: 0 7 Vp-p, 75 ohms PR/CR: 0 7 Vp-p, 75 ohms 80 MHz HD Pass Through HDMI Video Input/Output (HDMI Repeater block) 640 480p60Hz 720 480p59 94/60Hz 1440 480p59 94/60Hz (pixel sent 2times) 1280 720p59 94/60Hz 1920 1080i59 94/60Hz 1920 1080p59 94/60Hz 720 576p50Hz 1440 576p50Hz (pixel sent 2times) 1280 720p50Hz 1920 1080i50Hz 1920 1080p50Hz 1920 1080p24Hz General Power requirements 120 V AC, 60 Hz Power output (DIGITAL MEDIA PORT) DC OUT: 5 V, 700 mA Power consumption 350 W/480 VA (US/Canada) Power consumption (during standby mode) 0 7 W (when “HDMI Control” and “RS-232C Control” are set to “OFF”) Dimensions430 175 430 mm (width/height/depth) including projecting parts and controls Mass (Approx )14 5 kg Supplied accessories Operating Instructions Quick Setup Guide (1) HDMI CONTROL Guide (1) GUI Menu List (1) Optimizer microphone ECM-AC2 (1) FM wire antenna (aerial) (1) AM loop antenna (aerial) (1) AC power cord (mains lead) (1) Remote commander RM-AAL011 (1) Remote commander RM-AAU018 (1) R6 (size-AA) batteries (4) Design and specifications are subject to change without notice. AM tuner section Tuning range With 10-kHz tuning scale 530 1,710 kHz3) With 9-kHz tuning scale 531 1,710 kHz3) Antenna (aerial)Loop antenna (aerial) 3)You can change the AM tuning scale to either 9 kHz or 10 kHz After tuning in any AM station, turn off the receiver While holding down TUNING MODE, press POWER on the receiver All preset stations will be erased when you change the tuning scale To reset the scale to 10 kHz (or 9 kHz), repeat the procedure RadioFans.CN 收音机爱 好者资料库 3 STR-DA4300ES Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY. SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) Fig. A.Using an AC voltmeter to check AC leakage. 1.5 k0.15 F AC voltmeter (0.75 V) To Exposed Metal Parts on Set Earth Ground TABLE OF CONTENTS 1.SERVICING NOTES.5 2.GENERAL.8 3.DISASSEMBLY 3-1.Disassembly Flow . 12 3-2.Case . 13 3-3.Front Panel Block . 13 3-4.CIS Board, Tuner (FM/AM). 14 3-5.D.AUDIO Board, DSP Board. 14 3-6.TUNER Board, CONTROL Board . 15 3-7.PREOUT Board, S_SPTM Board . 15 3-8.D_VIDEO Board . 16 3-9.A_VIDEO Board . 16 3-10. MAIN Board, C_SPTM Board. 17 3-11. AC Board, Power Transformer (T001). 18 3-12. Power AMP Block. 18 4.TEST MODE. 19 5.ELECTRICAL ADJUSTMENTS. 23 6.DIAGRAMS 6-1.Block Diagram CONTROL Section . 25 6-2.Block Diagram DSP Section . 26 6-3.Block Diagram DIGITAL AUDIO Section . 27 6-4.Block Diagram HDMI Section . 28 6-5.Block Diagram VIDEO PROCESS Section . 29 6-6.Block Diagram ANALOG AUDIO Section . 30 6-7.Block Diagram POWER AMP Section . 31 6-8.Block Diagram VIDEO Section . 32 6-9.Block Diagram PANEL, CIS, XM/ SIRIUS RECEIVER, DMPORT Section . 33 6-10. Block Diagram POWER SUPPLY Section . 34 6-11. Schematic Diagram MAIN Board (1/4) . 36 6-12. Schematic Diagram MAIN Board (2/4) . 37 6-13. Schematic Diagram MAIN Board (3/4) . 38 6-14. Schematic Diagram MAIN Board (4/4) . 39 6-15. Printed Wiring Board MAIN Board . 40 6-16. Schematic Diagram D.AUDIO Board (1/5) . 41 6-17. Schematic Diagram D.AUDIO Board (2/5) . 42 6-18. Schematic Diagram D.AUDIO Board (3/5) . 43 6-19. Schematic Diagram D.AUDIO Board (4/5) . 44 6-20. Schematic Diagram D.AUDIO Board (5/5) . 45 6-21. Printed Wiring Board D.AUDIO Board (Component Side) . 46 6-22. Printed Wiring Board D.AUDIO Board (Conductor Side) . 47 6-23. Printed Wiring Board TUNER Board (Component Side) . 48 6-24. Printed Wiring Board TUNER Board (Conductor Side) . 49 6-25. Schematic Diagram TUNER Board (1/2) . 50 6-26. Schematic Diagram TUNER Board (2/2) . 51 6-27. Printed Wiring Board DSP Board (Side A) . 52 6-28. Printed Wiring Board DSP Board (Side B) . 53 6-29. Schematic Diagram DSP Board (1/4) . 54 6-30. Schematic Diagram DSP Board (2/4) . 55 6-31. Schematic Diagram DSP Board (3/4) . 56 6-32. Schematic Diagram DSP Board (4/4) . 57 6-33. Printed Wiring Boards CONNECTOR Section . 58 6-34. Schematic Diagram CONNECTOR Section . 59 6-35. Printed Wiring Board TEMPERATURE DETECTION Board . 60 4 STR-DA4300ES 6-36. Schematic Diagram TEMPERATURE DETECTION Board . 60 6-37. Printed Wiring Board A CLASS AMP Board . 61 6-38. Schematic Diagram A CLASS AMP Board (1/2) . 62 6-39. Schematic Diagram A CLASS AMP Board (2/2) . 63 6-40. Printed Wiring Board POWER AMP Board . 64 6-41. Schematic Diagram POWER AMP Board . 65 6-42. Printed Wiring Board PROTECTOR (F-C) Board . 66 6-43. Schematic Diagram PROTECTOR (F-C) Board . 67 6-44. Printed Wiring Boards PROTECTOR (SB/SURR) Section . 68 6-45. Schematic Diagram PROTECTOR (SB/SURR) Section . 69 6-46. Printed Wiring Board BIAS Board . 70 6-47. Schematic Diagram BIAS Board . 71 6-48. Printed Wiring Board PREOUT Board . 72 6-49. Schematic Diagram PREOUT Board . 73 6-50. Printed Wiring Boards SPEAKER Section . 74 6-51. Schematic Diagram SPEAKER Section . 75 6-52. Printed Wiring Board D_VIDEO Board (Component Side) . 76 6-53. Printed Wiring Board D_VIDEO Board (Conductor Side) . 77 6-54. Schematic Diagram D_VIDEO Board (1/10) . 78 6-55. Schematic Diagram D_VIDEO Board (2/10) . 79 6-56. Schematic Diagram D_VIDEO Board (3/10) . 80 6-57. Schematic Diagram D_VIDEO Board (4/10) . 81 6-58. Schematic Diagram D_VIDEO Board (5/10) . 82 6-59. Schematic Diagram D_VIDEO Board (6/10) . 83 6-60. Schematic Diagram D_VIDEO Board (7/10) . 84 6-61. Schematic Diagram D_VIDEO Board (8/10) . 85 6-62. Schematic Diagram D_VIDEO Board (9/10) . 86 6-63. Schematic Diagram D_VIDEO Board (10/10) . 87 6-64. Printed Wiring Board A_VIDEO Board (Component Side) . 88 6-65. Printed Wiring Board A_VIDEO Board (Conductor Side) . 89 6-66. Schematic Diagram A_VIDEO Board (1/4) . 90 6-67. Schematic Diagram A_VIDEO Board (2/4) . 91 6-68. Schematic Diagram A_VIDEO Board (3/4) . 92 6-69. Schematic Diagram A_VIDEO Board (4/4) . 93 6-70. Printed Wiring Board VIDEO3 Board . 94 6-71. Schematic Diagram VIDEO3 Board . 95 6-72. Printed Wiring Board CONTROL Board (Component Side) . 96 6-73. Printed Wiring Board CONTROL Board (Conductor Side) . 97 6-74. Schematic Diagram CONTROL Board (1/2) . 98 6-75. Schematic Diagram CONTROL Board (2/2) . 99 6-76. Printed Wiring Board CIS Board . 100 6-77. Schematic Diagram CIS Board . 101 6-78. Printed Wiring Board DISPLAY Board . 102 6-79. Schematic Diagram DISPLAY Board . 103 6-80. Printed Wiring Boards PANEL Section . 104 6-81. Schematic Diagram PANEL Section . 105 6-82. Printed Wiring Board DC-DC Board . 106 6-83. Schematic Diagram DC-DC Board . 107 6-84. Printed Wiring Board AC Board .108 6-85. Schematic Diagram AC Board . 109 7.EXPLODED VIEWS 7-1.Case Section .156 7-2.DISPLAY Board Section. 157 7-3.Front Panel Section . 158 7-4.AC/DC-DC Boards Section. 159 7-5.D.AUDIO/D_VIDEO Boards Section.160 7-6.A_VIDEO Board Section .161 7-7.Heat Sink Section .162 7-8.MAIN Board Section.163 8.ELECTRICAL PARTS LIST.164 5 STR-DA4300ES SECTION 1 SERVICING NOTES UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder