Yamaha-RXA-730-Service-Manual-Part-1电路原理图.pdf
Copyright (c) Yamaha Corporation All rights reserved. This manual is copyrighted by Yamaha and may not be copied or redistributed either in print or electronically without permission. P.O.Box 1, Hamamatsu, Japan 101 2 6 7 SERVICE MANUAL IMPORTANT NOTICE This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifi cally Yamaha Products, are already known and understood by the users, and have therefore not been restated. WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specifi ed. For these reasons, we advise all Yamaha product owners that any service required should be performed by an authorized Yamaha Retailer or the appointed service representative. IMPORTANT: The presentation or sale of this manual to any individual or fi rm does not constitute authorization, certifi cation or recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form. The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of Yamaha are continually striving to improve Yamaha products. Modifi cations are, therefore, inevitable and specifi cations are subject to change without notice or obligation to retrofi t. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss). IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit. CONTENTS TO SERVICE PERSONNEL .2 FRONT PANELS .34 REAR PANELS .58 REMOTE CONTROL PANEL .9 SPECIFICATIONS .1014 INTERNAL VIEW .1516 SERVICE PRECAUTIONS .16 DISASSEMBLY PROCEDURES .1724 UPDATING FIRMWARE .2527 SELF-DIAGNOSTIC FUNCTION .2870 POWER AMPLIFIER ADJUSTMENT .71 DISPLAY DATA .7273 IC DATA .7494 PIN CONNECTION DIAGRAMS .9597 BLOCK DIAGRAMS . 98101 WIRING DIAGRAMS . 102103 PRINTED CIRCUIT BOARDS .104125 SCHEMATIC DIAGRAMS .127142 REPLACEMENT PARTS LIST .143163 REMOTE CONTROL .164166 ADVANCED SETUP .167168 FIRMWARE UPDATING PROCEDURE .169180 AV RECEIVER RX-V675/HTR-6066/ RX-A730/TSR-6750 13.05 Note: When the DIGITAL P.C.B. or IC82 on DIGITAL (1) P.C.B. is replaced, this unit will display “Internal Error” and will not operate properly. The model name MUST be written to the backup IC (EEPROM: IC82 on DIGITAL (1) P.C.B.) to have proper operation. (For detailed procedure, refer to related Service News or Service Bulletin. Or contact your local Yamaha representative.) RX-V675/HTR-6066/ RX-A730/TSR-6750 This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHATSOEVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food. 1. Critical Components Information Components having special characteristics are marked and must be replaced with parts having specifications equal to those originally installed. 2. Leakage Current Measurement (For 120V Models Only) When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated from supply circuits. Meter impedance should be equivalent to 1500 ohms shunted by 0.15 F. TO SERVICE PERSONNEL Leakage current must not exceed 0.5mA. Be sure to test for leakage with the AC plug in both polarities. WARNING: CHEMICAL CONTENT NOTICE! All of the P.C.B.s installed in this unit and solder joints are soldered using the lead free solder. Among some types of lead free solder currently available, it is recommended to use one of the following types for the repair work. Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc + bismuth) Caution: As the melting point temperature of the lead free solder is about 30C to 40C (50F to 70F) higher than that of the lead solder, be sure to use a soldering iron suitable to each solder. About lead free solder WALL OUTLET EQUIPMENT UNDER TEST AC LEAKAGE TESTER OR EQUIVALENT INSULATING TABLE For U model “CAUTION” “F3701: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 2A, 250V FUSE.” “F3702: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 8A, 125V FUSE.” For C model CAUTION F3701: REPLACE WITH SAME TYPE 2A, 250V FUSE. F3702: REPLACE WITH SAME TYPE 8A, 125V FUSE. ATTENTION F3701: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE 2A, 250V. F3702: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE 8A, 125V. 2 RX-V675/HTR-6066/RX-A730/TSR-6750 RX-V675/HTR-6066/ RX-A730/TSR-6750 FRONT PANELS RX-V675 (U, C, R, T, A, B, G, F, L, S, H models) HTR-6066 (G, F models) 3 RX-V675/HTR-6066/RX-A730/TSR-6750 RX-V675/HTR-6066/ RX-A730/TSR-6750 RX-A730 (U, C, A, B, G, L models) TSR-6750 (U model) 4 RX-V675/HTR-6066/RX-A730/TSR-6750 RX-V675/HTR-6066/ RX-A730/TSR-6750 REAR PANELS RX-V675 (U, C models) RX-V675 (R, S models) RX-V675 (T model) 5 RX-V675/HTR-6066/RX-A730/TSR-6750 RX-V675/HTR-6066/ RX-A730/TSR-6750 H model RX-V675 (A model) RX-V675 (B, G, F models) RX-V675 (L, H models) 6 RX-V675/HTR-6066/RX-A730/TSR-6750 RX-V675/HTR-6066/ RX-A730/TSR-6750 RX-A730 (U, C models) HTR-6066 (G, F models) RX-A730 (A model) 7 RX-V675/HTR-6066/RX-A730/TSR-6750 RX-V675/HTR-6066/ RX-A730/TSR-6750 RX-A730 (L model) RX-A730 (B, G models) TSR-6750 (U model) 8 RX-V675/HTR-6066/RX-A730/TSR-6750 RX-V675/HTR-6066/ RX-A730/TSR-6750 Remote control sheet (T model) REMOTE CONTROL PANEL RAV501 9 RX-V675/HTR-6066/RX-A730/TSR-6750 RX-V675/HTR-6066/ RX-A730/TSR-6750 Audio Section Rated Output Power (Power Amp. Section) (1 kHz, 0.9 % THD) 1 channel driven U, C, R, T, A, B, G, F, L, S, H models (8 ohms) FRONT L/R .125 W/ch CENTER .125 W SURROUND L/R .125 W/ch SURROUND BACK L/R .125 W/ch B, G, F models (4 ohms) FRONT L/R .150 W/ch 2 channels driven simultaneously U, C, R, T, A, B, G, F, L, S, H models (8 ohms) FRONT L/R .105 W + 105 W CENTER .105 W SURROUND L/R .105 W + 105 W SURROUND BACK L/R .105 W + 105 W (20 Hz to 20 kHz, 0.09 % THD) 2 channels driven simultaneously U, C, R, T, A, B, G, F, L, S, H models (8 ohms) FRONT L/R .90 W + 90 W Maximum Effective Output Power (JEITA) R, T, L, H models (1 channel driven, 1 kHz, 10 % THD, 8 ohms) FRONT L/R .150 W/ch CENTER .150 W SURROUND L/R .150 W/ch SURROUND BACK L/R .150 W/ch Dynamic Power Per Channel (IHF) FRONT L/R (1 channel driven) (8 / 6 / 4 / 2 ohms) .130 / 170 / 200 / 240 W Damping Factor (20 Hz to 20 kHz, 8 ohms) FRONT L/R to SPEAKER-A .100 or more Input Sensitivity/Input Impedance (1 kHz, 100 W/8 ohms) AV5 etc. . 200 mV / 47 k-ohms Maximum Input Signal (1 kHz, 0.5 % THD) AV5 etc. (EFFECT ON) .2.3 V Output Level/Output Impedance AV OUT . 200 mV / 1.2 k-ohms SUBWOOFER (2 ch stereo and FRONT SP: small) . 1 V / 1.2 k-ohms ZONE2 OUT . 200 mV / 1.2 k-ohms Headphone Jack Rated Output/Output Impedance (1 kHz, 50 mV, 8 ohms) AV5 etc. input . 100 mV / 560 ohms Frequency Response (10 Hz to 100 kHz) AV5 etc., FRONT .0 / -3 dB Total Harmonic Distortion (20 Hz to 20 kHz, 50 W/8 ohms) AV5 etc. (PURE DIRECT) to FRONT SP OUT .0.06 % or less Signal to Noise Ratio (IHF-A Network) (Input shorted 250 mV) AV5 etc. (PURE DIRECT) to SP OUT . 100 dB or more Residual Noise (IHF-A Network) FRONT L/R to SP OUT .150 V or less Channel Separation (1 kHz / 10 kHz) AV5 etc. (Input 5.1 k-ohms shorted) . 60 dB or more / 45 dB or more Volume Control/Step .MUTE / -80 dB to +16.5 dB / 0.5 dB step Tone Control Characteristics Bass Boost/Cut . 6 dB / 0.5 dB step, at 50 Hz Turnover frequency .350 Hz Treble Boost/Cut .6 dB / 0.5 dB step, at 20 kHz Turnover frequency .3.5 kHz Filter Characteristics FRONT, CENTER, SURROUND, SURROUND BACK small (H.P.F.) .fc=40/60/80/90/100/110/120/160/200 Hz, 12 dB/oct. SUBWOOFER small (L.P.F.) .fc=40/60/80/90/100/110/120/160/200 Hz, 24 dB/oct. Optical Jack, Coaxial Jack Support Frequencies .32 kHz to 96 kHz Video Section Video Signal Type Monitor out (Wall paper) U, C, R models .NTSC T, A, B, G, F, L, S, H models .PAL Video conversion .NTSC/PAL Composite Video Signal Level .1 Vp-p / 75 ohms Component Video Signal Level Y .1 Vp-p / 75 ohms Pb/Pr .0.7 Vp-p / 75 ohms Video Maximum Input Level (VIDEO Conversion Off) .1.5 Vp-p or more Video Signal to Noise Ratio . 50 dB or more Monitor Out Frequency Response (VIDEO Conversion Off) Component video signal level .5 Hz to 60 MHz, -3 dB FM Section Tuning Range U, C models .87.5 to 107.9 MHz R, L, S, H models .87.5 to 108.0 / 87.50 to 108.00 MHz T, A, B, G, F models .87.50 to 108.00 MHz 50 dB Quieting Sensitivity (IHF) (1 kHz, 100 % MOD.) Mono .3 V (20.8 dBf) Signal to Noise Ratio (IHF) Mono .71 dB Stereo .69 dB Harmonic Distortion (1 kHz) Mono .0.3 % Stereo .0.5 % Antenna Input . 75 ohms unbalanced SPECIFICATIONS 10 RX-V675/HTR-6066/RX-A730/TSR-6750 RX-V675/HTR-6066/ RX-A730/TSR-6750 U .U.S.A. model C .Canadian model R .General model T.Chinese model A .Australian model B .British model G .European model F. Russian model L.Singapore model S .Brazirian model H .Thai model AM Section Tuning Range U, C models .530 to 1,710 kHz R, L, S, H models .530 to 1,710 / 531 to 1,611 kHz T, A, B, G, F models .531 to 1,611 kHz Antenna .Loop antenna General Power Supply U, C models .AC 120 V, 60 Hz R, S models .AC 110120/220240 V, 50/60 Hz T model .AC 220 V, 50 Hz A model .AC 240 V, 50 Hz B, G, F models .AC 230 V, 50 Hz L, H models . AC 220240 V, 50/60 Hz Power Consumption U, C models .400 W / 500 VA R, T, L, S, H models .270 W A, B, G,
