HarmanKardon-HKTS8-htss-sm维修电路原理图.pdf

harman/kardon SUB-TS7(HKTS 7 SUBWOOFER) SUB-TS8(HKTS 8 SUBWOOFER) SERVICE MANUAL harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev1 10/2006 RadioFans.CN CONTENTS BASIC SPECIFICATIONS . . . . . . . . . . . . . . . . 1 DETAILED SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . 2 CONTROLS or whether it has moved: i.e., the speaker that was not working still has no sound and the speaker that was working is still fine. If the problem is in the same place, the source of the problem is most likely with your receiver or amplifier, and you should consult the owners manual for that product for further information. If theproblem has followed the speaker, consult your dealer for further assistance or, if that is not possible, visit our Web site at for further information. If there is no sound from Check all wires and connections between receiver/amplifier and speaker. Make sure all wires are connected. the center speaker:Make sure none of the speaker wires are frayed, ccut, punctured, or touching other wires. If your receiver/processor is set in Dolby Pro Logic mode, make sure the center speaker is not in phantom mode. If your receiver/processor is set in Dolby Digital or DTS mode, make sure the receiver/processor is configured so that the center speaker is enabled. If the system plays at low Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. volumes but shuts off as Make sure none of the speaker wires are frayed, cut, punctured, or touching other wires. volume is increased: If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/amplifier. If there is low (or no) bass Make sure the SUB or Line-Level Inputs of the subwoofer and SUB or LFE output of your receiver output:or amplifier are properly connected by the RCA-type interconnect cable. If you are using the Subwfrs Speaker-Level Inputs , check your speaker cables to make sure they are all connected; that none of the wires are frayed, cut, punctured, or touching other wires; and that you have maintained the correct polarity by connecting positive terminals to positive terminals, and negative terminals to negative terminals. Make sure the subwoofer is plugged into an active electrical outlet and its Master Power Switch is switched on to the “” position. Check the speaker setup (bass management) settings in your A/V receiver or processor to make certain that the front, center and surround speakers are configured for “Small,” and that the subwoofer is set for “Yes” or “On.” If there is no sound from Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure the surround speakers:none of the speaker wires are frayed, cut, punctured, or touching other wires. Review proper operation of your receiver/processor and its surround sound features. Make sure the movie or TV show you are watching is recorded in a surround sound mode. If it is not, check to see whether your receiver/processor has other surround modes you may use. In Dolby Digital or DTS mode, make sure your receiver/processor is configured so that the surround speakers are enabled. Review the operation of your DVD player and the jacket of your DVD to make sure that the DVD features the desired Dolby Digital or DTS mode, and that you have properly selected that mode using both the DVD players menu and the DVD discs menu. SUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 10 Ref# Description Part Number Qty 1 Amplifier screw 352-AM04020D210 10 2 SUB-TS7/TS8 Amplifier Not for Sale 1 3 Port Tube Not for Sale 1 4 SUB-TS7/TS8 Cabinet Not for Sale 1 5 Logo 316-AG-00557 1 6 LED Not for Sale 1 7 Grille Not for Sale 1 8 Logo 316-AL-00553 1 9 10 woofer 25PF12DZB-DW01 1 10 Woofer screw 352-FM04020D605 5 11 Foot Pad 320-EVA-00057 4 SUB-TS7/TS8 harman/kardon SUB-TS7/TS8 harman/kardon 11 (See Mechanical Parts List on Pages 21-22) SUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 12 Test Set Up and Procedure Equipment needed: Function/signal generator/sweep generator Integrated Amplifier Multimeter Speaker cables Initial Control Settings: Power Switch OFF; Filter OFF Level MIN (Full CCW) Phase, Auto/On switches do not matter General Unit Function (UUT = Unit Under Test) 1) From the signal generator, connect one line level (RCA) cable to the Subwoofer Line Level Input jacks L/R on the UUT. Use a Y-cable from a mono source if necessary to connect to both inputs. Do not connect to the single, purple SUB input. 2) Turn on generator; adjust to 75mV, 50 Hz. 3) Plug in UUT; turn the power switch ON. Turn LEVEL control full clockwise (MAX) 4) LED should turn from Amber to Blue (on top of UUT); immediate and vigorous bass response should be heard and felt from port tube opening. 5) Turn off generator, turn LEVEL control full counterclockwise (MIN), and disconnect RCA cable. 6) Connect one pair of speaker cables to Speaker Level input terminal (IN) on UUT. Cables should be connected to an integrated amplifier fed by the signal generator. 7) Turn on generator and adjust so that speaker level input at the amplifier is 1.6V, 50 Hz. Turn LEVEL control full clockwise. 8) LED should turn from Amber to Blue; immediate and vigorous bass response should be heard and felt from the port tube opening. Sweep Function 1) Follow steps 6-8 above, using a sweep generator as a signal source. 2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any other noises. If any unusual noises are heard, remove woofers and test. Driver Function 1) Remove woofer from cabinet; detach + and - wire clips. 2) Check DC resistance of woofer; it should be 3.0 ohms 10% 3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V. 4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises. SUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 13 harman/kardon TECH TIPSTECH TIPS Troubleshooting tips and solutions to common service problems For models: HKTS7 SUB (SUB-TS7) TIP# HKTT2004-04 Subject: Improved filter performance Instructions: Change four 1/6W 5% CF Resistors in the PREAMP PCB of the HKTS 7 subwoofer amplifier. It is recommended this procedure be followed for every unit that has to be serviced, for any reason. Designator Original value New value h/k part number R223 51k 30k R224 51k 30k 110-16303J26 R226 27k 10k 110-16103j26 R227 27k 12k 110-16123j26 NOTE: Lack of this modification is unlikely to generate a complant It will have no effect in applications when the SUB input is used, or when the sub amp is used with the FILTER switch in the OFF position. Model Serial Number (120v) Serial Number (230v) Status Action SUB-TS7 ME048503390 and below ME048708198 and below In need of filter modification Change value of R223,224,226,227 SUB-TS7 ME048503391 and above ME048708199 and above Modified by Factory None Required SUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 14 SUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 15 SUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 16 SUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 17 SUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 18 SUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 19 SUB-TS7/TS8 120V Electrical parts list Part numberDescriptionReference Designator LIMITER PCB Resistors 110- 16103j26 Resistor 10K 1/6W 5% CF 26mm R301,R303,R304,R308,R309,R314, 110- 16153j26Resistor 15K 1/6W 5% CF 26mm R302, 110- 16223j26 Resistor 22K 1/6W 5% CF 26mmR310,R312, 110- 16333j26Resistor 33K 1/6W 5% CF 26mmR305, 110- 16474j26Resistor 470K 1/6W 5% CF 26mmR307, 110- 16751j26Resistor 750 1/6W 5% CF 26mmR311,R313, 110- 16755j26Resistor 7.5M 1/6W 5% CF 26mmR306, Capacitors 135- 3226m50 Elec. Capacitor 22U 50V 20% C301, 135- 3476m25 Elec. Capacitor 47U 25V 20% C304, 130- 2f104z503disk capacitor 0.1U 50V +80/- 20%C305,C306, 132- 103j503 Mylar capacitor 0.01U 50V 5% C302,C303, 162- 10059001Single wire 50mm WHITE UL1007 AWG26 Semiconductors 190- 16tl074cnI.C TL074CN ST QUAD OP- AMP+B78U301, 192- 027c1815grTransistor 2SC1815GR NPNQ301,Q302, 197- 131n4148Diode1N4148 26mm D301,D302, Miscellaneous 162- 501590027PIN 150mm AWG26 UL 2468P302, 175- 9f40hr2 connector 40PIN PITCH=2.54mm PREAMP PCB Resistors 110- 12472j52Resistor4.7K 1/2W 5% CF 52mm R201,R202, 110- 16102j26Resistor 1K 1/6W 5% CF 26mm R213,R214,R215,R254,R209,R212,R216,R217, 110- 16103j26Resistor 10K 1/6W 5% CF 26mm R218,R220,R221,R222,R225,R228,R229,R230, R232,R235,R240,R248,R260,R270, 110- 16104j26Resistor 100K 1/6W 5% CF 26mmR231,R263,R266, 110- 16105j26Resistor 1M 1/6W 5% CF 26mm R259, 110- 16122j26Resistor 1.2K 1/6W 5% CF 26mmR265, 110- 16124j26Resistor 120K 1/6W 5% CF 26mmR233, 110- 16151j26Resistor 150 1/6W 5% CF 26mmR253, 110- 16154j26Resistor 150K 1/6W 5% CF 26mmR252, 110- 16183j26Resistor 18K 1/6W 5% CF 26mm R262, 110- 16203j26Resistor 20K 1/6W 5% CF 26mm R237,R238, 110- 16205j26Resistor 2M 1/6W 5% CF 26mm R257, 110- 16223j26Resistor 22K 1/6W 5% CF 26mmR247,R255,R256, 110- 16273j26Resistor 27K 1/6W 5% CF 26mmR226,R227, 110- 16472j26Resistor 4.7K 1/6W 5% CF 26mmR200,R207,R258, 110- 16473j26Resistor 47K 1/6W 5% CF 26mm R219,R249,R250,R251,R264 110- 16512j26Resistor 5.1K 1/6W 5% CF 26mmR210,R211, 110- 16513j26Resistor 51K 1/6W 5% CF 26mm R223,R224, 110- 16752j26Resistor 7.5K 1/6W 5% CF 26mm TAR234, 110- 16913j26Resistor 91K 1/6W 5% CF 26mm R203,R204,R205,R206, 115- h503a102Variable resistor RV16AE- 20B2- 15K- A54- 104(A50K)VR201 Capacitors 129- a154j633Mylar capacitor 0.15U 63V 5% MSCC221,C222, 129- a224j633Mylar capacitor 0.22uF 63V 5% MSCC218 130- 2b221k503disk capacitor 220P 50V 10% C200,C204,C205,C207,C208,C210,C211,C212, C214,C220,C230,C237, 130- 2b470k503disk capacitor 47P 50V 10% C229, 130- 2f104z503disk capacitor 0.1U 50V +80/- 20%C232,C242,C244,C245,C246,C252,C254,C256, SUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 20 Part numberDescriptionReference Designator PREAMP PCB 132- 183j503 Mylar capacitor 0.018uF 50V 5% C223, 132- 223ja03 Mylar capacitor 0.022uF 100V 5% C215, 132- 473j503 Mylar capacitor 0.047U 50V 5% C224, 132- 563j503 Mylar capacitor 0.056U 50V 5% C216, 132- 823j503 Mylar capacitor 0.082U 50V 5% C217, 135- 3105m50 elec. capacitor 1U 50V 20% C228, 135- 3106m50 Elec. Capacitor 10uF 50V 20% C201,C202,C206,C213,C219,C231,C241,C243, C251,C253, 135- 3107m16 Elec. Capacitor 100uF 16V 20% C234, 135- 3226m50 Elec. Capacitor 22U 50V 20% C225, 135- 3227m16 Elec. Capacitor 220U 16V 20% C233, Semiconductors 192- 027c1815grTransistor 2SC1815GR NPNQ201,Q206,Q207,Q208, 197- 131n4148Diode 1N4148 26mm D201,D202,D203,D204,D205,D206,D207,D208, D214,D215,D216, 199- 15000335ZENER diode 3.3V 1/2W 52mm D213, 162- 503320032PIN 330mm RED/GREEN LEDD209, 190- 06m4558dI.C. OPA 4558D Dual Op- AmpU203, 190- 16tl074cnI.C TL074CN ST Quad Op- AmpU201,U202, Miscellaneous 162- a016d001wire assembly UL1007 160/80mm#26 174- 0rca313vRCA JACK RCA- 313G V/R/WJK201, 174- 20810360gSPK JK BP 8PINJK202, 175- 1b08v01 connector 8 PIN PITCH=2.0mm 180- tms7210vSWITCH SLIDE 6PIN MS7210VSW201,SW202,SW203, 362- FE- 00041PCB bracket 11.75*8.5*12.5H MAIN PCB Resistors 110- 14472j26Resistor 4.7K 1/4W 5% CF 26mmR147,R150, 110- 14681j26Resistor 680 1/4W 5% CF 26mmR148,R151, 110- 16101j26Resistor 100 1/6W 5% CF 26mmR120, 110- 16102j26Resistor 1K 1/6W 5% CF 26mm R124, 110- 16103j26Resistor 10K 1/6W 5% CF 26mm R134, 110- 16105j26Resistor 1M 1/6W 5% CF 26mm R143, 110- 16123j26Resistor 12K 1/6W 5% CF 26mm R135,R139, 110- 16152j26Resistor 1.5K 1/6W 5% CF 26mmR103,R123,R136,R137,R141,R142, 110- 16153j26Resistor 15K 1/6W 5% CF 26mm R118,R145,R152,R154, 110- 16154j26Resistor 150K 1/6W 5% CF 26mmR131, 110- 16181j26Resistor 180 1/6W 5% CF 26mmR111,R114 110- 16182j26Resistor 1.8K 1/6W 5% CF 26mmR153, 110- 16223j26Resistor 22K 1/6W 5% CF 26mmR128,R129,R133, 110- 16332j26Resistor 3.3K 1/6W 5% CF 26mmR106,R107,R144 110- 16392j26Resistor 3.9K 1/6W 5% CF 26mmR105,R108, 110- 16393j26Resistor 39K 1/6W 5% CF 26mm R126, 110- 16470j26Resistor 47 1/6W 5% CF 26mmR112,R113,R115,R116, 110- 16471j26Resistor 470 1/6W 5% CF 26mmR140, 110- 16472j26Resistor 4.7K 1/6W 5% CF 26mmR110,R125,R130, 110- 16473j26Resistor 47K 1/6W 5% CF 26mm R101, 110- 16560j26Resistor 56 1/6W 5% CF 26mmR117, 110- 16563j26Resistor 56K 1/6W 5% CF 26mm R104, 110- 16682j26Resistor 6.8K 1/6W 5% CF 26mmR109, 110- 10821jk2Resistor 820 1W 5%R132, 110- 122r2j15Resistor 2.2 1/2W 5%R127, 110- 20331jk2Resistor 330 2W 5% 5mmR146,R149, 113- 50r10j10Cermemt resistor 0.1 5W 5% R121,R122, 114- 03302m0 Variable resistor 3K 0.3W 20%R138, SUB-TS7/TS8 harman/kardonSUB-TS7/TS8 harman/kardon 21 Part numberDescriptionReference Designator MAIN PCB Semiconductors 192- 027c1815grTransistor 2SC1815GR NPNQ102,Q111,Q112,Q113,Q118 192- 028a1015grTransistor 2SA1015GR PNPQ114,Q116, 192- 1672n5551Transistor 2N5551 NPNQ103,Q109, 192- 1682n5401Transistor 2N5401 AI- PNP 350VQ104,Q110, 197- 131n4148Diode 1N4148 26mm D101,D103,D105,D108, 199- 15000335ZENER diode 3.3V 1/2W 52mm D102, 199- 15000625ZENER diode 6.2V 1/2W 52mm D106,D107, 199- 15001605ZENER diode 16V 1/2W 52mm D109, 192- 021c1815grTransistor 2SC1815GR NPNQ101,Q115, 192- 021tip35cTransistor TIP35C NPNQ107, 192- 022tip36cTransistor TIP36C PNPQ108, 192- 201d882yTransistor KSD882Y NPNQ117, 192- 202b772yTransistor KSB772Y PNPQ119, 192- 991d669aTransistorHI- SINCERITY HSD669A NPNQ106, 192- 992b649tTransistor HSB649T PNPQ105, 197- 00kbl405bridge diode 4A 500V KBL405D110, 197- 101n4002Diode 1N4002 D104, 190- 06m4558dI.C. OPA 4558D Dual Op- AmpU101, Capacitors 130- 2b102k503disk capacitor 1000P 50V 10% C116, 130- 2f104z503disk capacitor 0.1U 50V +80/- 20%C108,C113,C115,C119, 130- 3f473m503disk capacitor 0.047U 50V 20% C106, 130- sl101k503disk capacitor 100P 50V SL 10% C139,C140, 132- 104j503 Mylar capacitor 0.1U 50V 5% C107, 132- 223ja03 Mylar capacitor 0.022uF 100V 5% C124,C125,C126,C128, 135- 3105m50 elec. Capacitor 1U 50V 20% C105,C112, 135- 3107m16 Elec. Capacitor 100uF 16V 20% C109,C117,C120, 135- 3226m50 Elec. Capacitor 22U 50V 20% C114,C118, 135- 3227m10 Elec. Capacitor 220U 10V 20% C129,C130, 135- 3227m16 Elec. Capacitor 220U 16V 20% C111, 135- 3476m25 Elec. Capacitor 47U 25V 20% C103, 130- 3f472md00disk capacitor 4700P 400V 20%for Power Switch 132- 223ja03 Mylar capacitor 0.022uF 100V 5% C123,C127, 135- 3107m16 Elec. Capacitor 100uF 16V 20% C110, 135- 4688m50 Elec. Capacitor 6800U/50V 20%C121,C122, Miscellaneous 171- udhss124drelay 5A 24V UD