Akai-MPC1000-mpc-sm维修电路原理图.pdf

SERVICE MANUAL 1 Music production Center RadioFans.CN 收音机爱 好者资料库 SERVICE MANUAL 2 SAFETY INSTRUCTIONSINFORMATIONS 1. Parts identified by the ? symbol are critical for safety. Replace them only with the parts number specified. 2. In addition to safety, other parts and assemblies are specified for conformance with such regulations as those applying to spurious radiation. These must also be replaced only with the specified replacements. Examples : Noise blocking capacitors, noise blocking filters, etc. 3. Use specified internal wiring. Note especially : 1) Wires covered with PVC tubing 2) Double insulated wires 3) High voltage leads 4. Use specified insulating materials for hazardous live parts. Note especially : 1) Insulation Tape 2) PVC tubing 3) Spacers (insulating barriers) 4) Insulation sheets for transistors 5) Plastic screws for fixing micro switches 5. When replacing AC primary side components (trans- formers, power cords, noise blocking capacitors, etc.), wrap the ends of the wires securely around the terminals before soldering. 6. Make sure that wires do not contact heat producing parts (heat sinks, oxide metal film resistors, fusible resistors, etc.). 7. Check that replaced wires do not contact sharp edged or pointed parts. 8. Also check areas surrounding repaired locations. 9. Make sure that foreign objects (screws, solder droplets, etc.) do not remain inside the set. SAFETY CHECK AFTER SERVICING After servicing, make measurements of leakage-current or resistance in order to determine that exposed parts are acceptably insulated from the supply circuit. The leakage- current measurement should be done between accessible metal parts (such as chassis, ground terminal, microphone jacks, signal input/output connectors, etc.) and the earth ground through a resistor of 1500 ohms paralleled with a 0.15 ? F capacitor, under the units normal working conditions. The leakage-current should be less than 0.5 mA rms AC. The resistance measurement should be done between accessible exposed metal parts and power cord plug prongs with the power switch (if included) “ON”. The resistance should be more than 2.2 M ohms. SYMBOLS FOR PRIMARY DESTINATION Unit destinations are indicated with letters as shown below. SymbolsPrincipal Destinations AU.S.A BEngland EEurope JJapan VGermany X1Japan X4Universal Area MAKE YOUR CONTRIBUTION TO PROTECT THE ENVIRONMENT Used batteries with the ISO symbol for recycling as well as small accumulators (rechargeable batteries), mini-batteries (cells) and starter batteries should not be thrown into the garbage can. Please leave them at an appropriate depot. PRECAUTIONS FOR LITHIUM BATTERY The lithium battery may explode when incorrectly replaced. OBSERVE THE FOLLOEING WHEN REPLACING ?Replace with the same make and type or equivalent recom mended by manufacturer. ?Place battery in correct polarity. ?Do not short the terminals. ?Do not charge battery. ?Do not dispose of battery in fire. RadioFans.CN 收音机爱 好者资料库 SERVICE MANUAL 3 * The specifications are subject to change without the prior notice. I. SPECIFICATIONS General Display240 x 64 dot graphic LCD w/back light Memory card slot Compact Flash (The size of the compact flash card the MPC1000 can handle is from 32MB to 2GB) Dimentions (W x H x D)330 x 75.5 x 228.2(Max 234.6) Weight3.45kg Power reqirement19W Sound generator Sampling rate44.1kHz Memory capacity16MB standard (11.5MB for sound memory), expandable to 128MB Recording time136sec. (16MB, MONO), 24m28sec. (128MB, MONO) Memory expansion slot1 x for optional EXM128 Data format16-bit linear Polyphony32 Dynamic filtering2 x 2-pole filter per voice Filter typeLow pass, Band pass, High pass Preset sound memory5MB Number of programs24 Effects Effects2 stereo effects and Master effect Effect type Chorus, Flanger, Bit grunger, 4 band EQ, Compressor, Phase shifter, Tremolo, Flying pan, Reverb Master effect: 4 band EQ, Compressor Sequencer Maximum events100,000 notes Resolution96 parts per 1/4-note Sequences99 Tracks per sequence64 MIDI output channels32 (16 channels x 2 outputs) Song mode20 songs, 250 steps per song Drum pad16 (velocity and pressure sensitive) Drum pad banks4 Sync mode MIDI clock SERVICE MANUAL 4 * The specifications are subject to change without the prior notice. Inputs / Outputs Record input (L and R) 1/4-inch stereo phone x 2, balanced -40dBu, input impedance 11k ohms; Max. Input level +10dBu Digital inputRCA-pin x 1 S/PDIF Stereo output (L and R) 1/4-inch phone x 2 unbalanced +11dBu, output impedance 1k Ohms, Max. output level +17dBu 4 individual outputs 1/4-inch phone x 4 unbalanced +11dBu, output impedance 1k Ohms, Max. output level +17dBu Phones output1/4-inch stereo phone x 1, 200mW / 100 ohms Digital outputRCA-pin x 1 S/PDIF MIDI inputs5-pin DIN x 2 MIDI outputs5-pin DIN x 2 USB Slave connector x 1, USB MASS STORAGE CLASS support. (You need Windows 2000/Me/XP or later version, or MacOS 9.x/10.x or later version. ) Footswitches1/4-inch phone x 2 Standard accessories Standard accessories32MB Compact Flash card, Power cable, Operators manual Options EXM128128MB expansion memory card Data Compatibility (THRU Computer) MPC2000XLSEQ, WAV, PGM (Most parameters of PGM file can be loaded.) MPC4000 SEQ, WAV , PGM (DRUM program only. Only note assign and tune are loaded.) MPC3000No compatibility Z4/Z8WAV only S5000/6000WAV only S1000/3000No compatibility SERVICE MANUAL 5 II. DISASSEMBLY In case of trouble, etc., necessitating dismantling, please dismantle in the order shown in the illustrations. Reassemble in the reverse order. ZS-820454X ZS-820455X ZS-820454X ZS-820454X ZS-820454X ZS-820454X SERVICE MANUAL 6 III. PRINCIPAL PARTS LOCATION BA - L4033A502D PC OPERATION - F BLK BA - L4033A502A PC OPERATION - R BLK BA - L4033A502C PC OPERATION - L BLK BA - L4033A502B PC PAD BLK BA - L4033A502E PC MIDI BLK BA - L4033A501E PC FILTER BLK BA - L4033A501A PC CPU BLK BA - L4033A501D PC HD CONNECT BLK BA - L4033A501C PC FRONT BLK BA - L4033A501B PC AD/DA BLK EM - 821776X IND LCD PS24064LRU - ETA - H03 BP - 821839X SW POW SNP - 9031 SERVICE MANUAL 7 IV. SUPPLEMENTARY INFORMATION Update procedure =How to copy the OS binary file to a CF card using a MPC1000 and a computer= Below procedure will utilize the MPC1000 as a Compact flash writer. Required Equipment : Compact Flash (CF), Computer with USB mass storage class support (Windows XP/ME/2000 or Mac OSX, OS9.x) 1. Copy/Download the OS data to a computer s hard disc drive and extract it s data. 2. Insert a Compact Flash card into the MPC1000. 3. Turn on the power of the MPC1000. 4. Go to Load mode, then press USB (F4). 5. Connect a USB cable between the computer and the MPC1000. (Display will change from “Status=Not Connected ” to “Status=Connected ”) 6. The CF in the MPC1000 will be mounted as a drive on the computer. 7. Copy the OS binary file to the CF in the MPC1000. 8. Disconnect the USB cable. (MPC1000 will not accept any user in put while a USB cable is connected) Note: The OS data can also be copied to a Compact Flash card using any other Compact Flash card reader/writer. In this case it is not necessary to connect the MPC1000 to a computer. =How to update the MPC1000= MPC1000 is updated using a Compact Flash card containing OS data. Insert a CF containing OS data into the MPC1000. Turn on the power of the MPC1000 while pressing down the “Window” button. To start the update process, p ress the “REC” button. After the update process is finished the MPC1000 will re- boot automatically. Note: The MPC1000 can not be updated from a computer via USB directly updating is only possible using a CF card. =Hidden model=( Note: V1.06 is not supported.) The MPC1000 has the following hidden modes, which can be accessed by certain input sequences or holding down a key while powering on the unit. Currently these modes are not supported in OS Version 1.06. Owner Name Mode Other F3/FOOTSW F6 Enter owner name in the startup screen, “Owner Name” will be displayed. Initialize parameter Hold down the ERASE button while powering on the unit. Memory Check Hold down the PLAY button while powering on the unit. Demo mode Hold down the Bank “D” button while powering on the unit. In this mode “Internal memory” on the Save page can not be selected . In the startup screen “Demo” will be displayed instead of “MPC1000”. Once demo mode has been activated it will remain active even if power is turned off and on again. To turn off the Demo mode, hold down the Bank “D” button while powering on the unit. 1. 2. 3. 1. 2. 3. 4. SERVICE MANUAL 8 Test program Test programs on the MPC1000 can be run either using a Test OS or a JIG PC Flash Rom. Running the test Program using a Test OS A test program can be installed on the MPC1000 by updating it with a Test OS. The Test OS must be copied to a CF card from which it will be written to the Flash ROM of the MPC1000. The installation procedure is the same as for a normal OS update. For a description of the test mode functions, refer to the “MPC1000 Test Program list”. Note: Once the Test OS is installed, the unit will always start up using the Test OS, until the regular OS is re-installed. Running the test Program using a JIG PC Flash ROM MPC1K (AJ - 771312J) The PC Flash ROM is used during repair for the testing jig and boot block recovery. To access the test program on the PC Flash ROM MPC1K follow this procedure: 1. Turn off the MPC1000 and open the unit. 2. Insert the PC Flash MPC1K ROM into J110 on the CPU board. 3. Turn on the MPC1000 to start up the Test OS from the PC Flash ROM. MPC1000 TEST OS Starting DisplayStarting Display F1F1 F2F2 F3F3 F4F4 F5F5 F6F6 PANELPANEL MEMORYMEMORY AUDIOAUDIO MIDI-MIDI- F.SW-F.SW- - PANEL TESTPANEL TEST MEMORY TESTMEMORY TEST A/D selectedA/D selected SPDIF selected SPDIF selected test tonetest tone OUTA IN 1:OK OUTB IN2 FAILEDOUTA IN 1:OK OUTB IN2 FAILED F.SW1 : ON F.SW2 : OFFF.SW1 : ON F.SW2 : OFF F1F1 F2F2 F3F3 F4F4 F5F5 F6F6 F1F1 F2F2 F3F3 F4F4 F5F5 F6F6 F1F1 F2F2 F3F3 F4F4 F5F5 F6F6 F1F1 F2F2 F3F3 F4F4 F5F5 F6F6 F1F1 F2F2 F3F3 F4F4 F5F5 F6F6 -KEY-KEY- -JOG-JOG- -PAD-PAD- -LCD-LCD- -LED-LED- EXIT-EXIT- SDRAMSDRAM -CF-CF- -HDD-HDD- -DSP-DSP- FLASHFLASH EXIT-EXIT- -A/D-A/D- SPDIFSPDIF TONE-TONE- - - EXIT-EXIT- STARTSTART - - - - - - - - - EXIT-EXIT- EXIT-EXIT- (Each connection result dislayed)(Each connection result dislayed) (Foot SW status displayed)(Foot SW status displayed) SDRAM TESTSDRAM TEST CF CARD TESTCF CARD TEST HDD TESTHDD TEST FLASH WRITINGFLASH WRITING F1F1 F2F2 F3F3 F4F4 F5F5 F6F6 F1F1 F2F2 F3F3 F4F4 F5F5 F6F6 F1F1 F2F2 F3F3 F4F4 F5F5 F6F6 F1F1 F2F2 F3F3 F4F4 F5F5 F6F6 SIMPLSIMPL FULL-FULL- EXIT-EXIT- - - - SIMPLSIMPL DETECDETEC SECTRSECTR BACUPBACUP ERASEERASE EXIT-EXIT- SIMPLSIMPL DETECDETEC SECTRSECTR BACUPBACUP ERASEERASE EXIT-EXIT- P_OS-P_OS- -USB-USB- LIBC-LIBC- LIBH-LIBH- - EXIT-EXIT- By Pressing Keys correspond 35 boxes change to negative.(#1)By Pressing Keys correspond 35 boxes change to negative.(#1) JOG,FADER1,FADER2,input,value,displyedJOG,FADER1,FADER2,input,value,displyed Each Pad No., and input value displayed. Plural input displayed ErrorEach Pad No., and input value displayed. Plural input displayed Error All dot of LCD change to Black. Contrast adjusting by JOGAll dot of LCD change to Black. Contrast adjusting by JOG All LEDs lightAll LEDs light (#2)When press Keys with LED, LED light while pressing switches. (#1Press F6 twice = EXIT) (#2)When press Keys with LED, LED light while pressing switches. (#1Press F6 twice = EXIT) SDRAM simple checkSDRAM simple check SDRAM all area READ/WRITE checkSDRAM all area READ/WRITE check CF card simple checkCF card simple check Type of CF card displayType of CF card display CF card all area READ/WRITE checkCF card all area READ/WRITE check For developmentFor development Delete CF card dataDelete CF card data HDD simple checkHDD simple check Type of HDD displayedType of HDD displayed HDD all area READ/WRITE checkHDD all area READ/WRITE check For developmentFor development Delete HDD dataHDDDelete HDD dataHDD No functionNo function Write Test OS to Flash ROMWrite Test OS to Flash ROM Data (OS/Liblary) transport via USBData (OS/Liblary) transport via USB No functionNo function No functionNo function A/D inputting signal output to all OUTPUT.A/D inputting signal output to all OUTPUT. SPDIF inputting signal output to all OUTPUT. (#3)SPDIF inputting signal output to all OUTPUT. (#3) FULL bit signal output to all OUTPUT.FULL bit signal output to all OUTPUT. (#3)A/D-L MAIN-L, 1,3 A/D-R MAIN-R, 2,4(#3)A/D-L MAIN-L, 1,3 A/D-R MAIN-R, 2,4 Start Loop back Test, MIDI OUT A - MIDI IN 1, MIDI OUT B - MIDI IN 2Start Loop back Test, MIDI OUT A - MIDI IN 1, MIDI OUT B - MIDI IN 2 SERVICE MANUAL 9 V. PARTS LIST HOW TO USE THIS PARTS LIST 1. This Parts List lists those parts which are considered necessary for repairs. 2. Parts not shown in the Parts List will not in principle be supplied. 3. How to read the Parts List. WARNING ? ? ? ? ? INDICATES SAFETY CRITICAL COMPONENTS. FOR CONTINUED SAFETY, REPLACE SAFETY CRITICAL COMPONENTS ONLY WITH MANUFACTURERS RECOMMENDED PARTS. AVERTISSEMENT ? ? ? ? ? IL INDIQUE LES COMPOSANTS CRITIQUES DE SCURIT. POUR MAINTENIR LE DEGR DE SCURITDE LAPPAREIL, NE REMPLACER QUE DES PICES RECOMMANDEES PAR L FABRICANT. 1. PC MAIN BOARD BLK Ref. No.Part No.Description D5ED-431276CD SCHOT 1S30-J T05 D110ED-431276CD SCHOT 1S30-J T05 : : IC5EI-811073JICTRC-6593 IC10EI-811068JIC HD74HC157FP Service parts classification These reference symbols correspond with component symbols in the Schematic Diagrams. 2. FINAL ASSEMBLY BLK Ref. No.Part No.Description 1.SA-349332FOOT 2.ZS-344754CST PAN30 x06STL CMT : : 44.SP-417333JCOVER TOP 45.ZS-418385JBT BID30X06STL BNI EATRH LOCK 46-A? EW-380905JAC CORD 250S KP300 KS16A H B J J 46-B? EW-368420J1AC CORD 200SKP30KS B AC A 46-C? EW-410608JAC CORD 250 KP4819D KS31A B E E,V Symbols for primary destination A U.S.A.J Japan B EnglandV Germany E Europex1 Japan X4 Universal Area Safety critical component This number corresponds with the individual parts index number in the figure. ATTENTION 1. When placing an order for parts, be sure to list the Part No., Model No. and the description of each part. Otherwise, the non-delivery of the part or the delivery of a wrong part may result. 2. Please make sure that Part No. is correct when ordering. If not, a part different from the one you ordered may be delivered. 3. Since the parts shown in Parts List or Preliminary Service Manual may have been the subject of changes, please use this Parts List for all future reference. SERVICE MANUAL 10 Ref. No.Part No.Description Ref. No. Part No.DescriptionIC203EI - 812479JIC NJM5532M FPT1T32P IC204EI - 812479JIC NJM5532M FPT1T32P 1BA - L4033A020A PC(#) MAIN BLK MPC1000I