Onkyo-RDC7-avc-sm 电路图 维修手册.pdf

《Onkyo-RDC7-avc-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Onkyo-RDC7-avc-sm 电路图 维修手册.pdf（72页珍藏版）》请在收音机爱好者资料库上搜索。

1、AV Controller MODEL RDC-7 SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK ON THE SCHEMATIC DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR RISK OF FIRE AND ELEC- TRIC SHOCK. REPLACE THESE COMPONENTS WITH ONKYO PARTS WHOSE PARTS NUMBERS APPEAR AS SHOWN IN THIS MANUAL. MAKE LEAKAGE-CURR

2、ENT OR RESISTANCE MEASUREMENTS TO DETERMINE THAT EXPO- SED PARTS ARE ACCEPTABLY INSULATED FORM THE SUPPLY CIRCUIT BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER. No.3653 RDC-7 Sep,2000 Silver model UDD, UDT UPP,UPT UGT 120V AC, 60Hz 220 -230V AC, 50/60Hz 230V AC, 50Hz SPECIFICATIONS- SERVICE PROCEDU

3、RE- FRONT PANEL FACILITIES- REMOTE CONTROLLER- REAR PANEL FACILITIES- EXAMPLE OF HOW TO CONNECT YOUR EQUIPMENT- CONNECTING POWER AMPLIFIERS- DISASSEMBLING PROCEDURES- ASSEMBLING PROCEDURES- IC BLOCK DIAGRAMS AND DESCRIPTIONS- WIRING VIEW- CHASSIS EXPLODED VIEW- CHASSIS EXPLODED VIEW PARTS LIST- MAIN

4、 MICROPROCESSOR CONNECTION DIAGRAM- MAIN MICROPROCESSOR TERMINAL DESCRIPTION- SUB MICROPROCESSOR CONNECTION DIAGRAM- SUB MICROPROCESSOR TERMINAL DESCRIPTION- PC BOARD CONNECTION VIEW- BLOCK DIAGRAM- PRINTED CIRCUIT BOARD PARTS LIST- SCHEMATIC DIAGRAM / PRINTED CIRCUIT BOARD VIEW- CONFIRMATION- FL TU

5、BE VIEW- PACKING VIEW- 2 3 4 5 6 8 10 11 12 1330 31 33 35 37 39 41 43 45 47 49 5094 95 96 97 TABLE OF CONTENTS RadioFans.CN 收音机爱 好者资料库 RDC-7 2 GENERAL Power SupplyAC 120 V, 60 Hz AC 230 V, 50 Hz AC 220 V, 50/60 Hz Power Consumption75 W Dimensions (W H D)450 196 440 mm 17-11/16 7-11/16 17-5/16 Weight

6、16.2 kg, 35.7 lbs. REMOTE CONTROLLER TransmitterInfrared Signal rangeApprox. 5 meters, 16 ft. Power supplyTwo “AA” batteries (1.5 V 2) Specifications and features are subject to change without notice. Power supply and voltage vary depending on the area in which the unit is purchased. CONTROLLER SECT

7、ION Input Sensitivity and Impedance PHONO2.5 mV, 50 kohms LINE (CD, TAPE 1-2, DVD, VIDEO 1-5)200 mV, 50 kohms MULTICHANNEL INPUT (FRONT L/C/R, SURROUND L/R, SURROUND BACK L/R)200 mV, 50 kohms (SUBWOOFER)36 mV, 50 kohms COAXIAL 1-5 (DIGITAL)0.5 Vp-p, 75 ohms DVD, VIDEO1-51 Vp-p, 75 ohms 1 Vp-p, 75 oh

8、ms (Y) 0.28 Vp-p, 75 ohms (C) COMPONENT VIDEO 1-31 Vp-p, 75 ohms (Y) 0.5 Vp-p, 75 ohms (PB, PR) Output Level and Impedance Rec out (TAPE 1-2, VIDEO 1-2) 200 mV, 2.2 kohms Pre out(RCA)1 V, 470 ohms Pre out(XLR)1 V, 470 ohms ZONE 2 OUT100mV, 470 ohms VIDEO (VIDEO 1-2, MONITOR OUT, ZONE 2 OUT)1 Vp-p, 7

9、5 ohms 1 Vp-p, 75 ohms (Y) 0.28 Vp-p, 75 ohms (C) COMPONENT VIDEO OUT1 Vp-p, 75 ohms (Y) 0.5 Vp-p, 75 ohms (PB, PR) Phono Overload110 mV RMS at 1 kHz, 0.5% T.H.D. Frequency Response20 Hz to 30 kHz : 1dB (CD in, Direct mode) 5 Hz to 100 kHz : +1dB,-3dB (CD in, Direct mode) RIAA Deviation:20 to 20 kHz

10、 : 0.8 dB Tone Control Bass10 dB at 100 Hz Treble10 dB at 10 kHz Signal-to-Noise Ratio (Stereo) PHONO80 dB (IHF A, 5 mV input) CD/TAPE100 dB (IHF A, 0.5 V input) TUNER SECTION FM Tuning Range87.5 108.0 MHz (50 kHz steps) Usable Sensitivity Mono11.2 dBf, 1.0 V (75 ohms IHF) 0.9 V (75 ohms DIN) Stereo

11、:17.2 dBf, 2.0 V (75 ohms IHF) 23 V (75 ohms DIN) 50 dB Quieting Sensitivity Mono17.2 dBf, 2.0 V (75 ohms) Stereo37.2 dBf, 20 V (75 ohms) Capture Ratio2.0 dB Image Rejection Ratio USA & Canadian models40 dB European & Australian models : 85 dB IF Rejection Ratio90 dB Signal-to-Noise Ratio Mono76 dB

12、Stereo70 dB Alternate Channel Attenuation55 dB Selectivity50 dB (DIN) AM Suppression Ratio50 dB Total Harmonic Distortion Mono0.2 % Stereo0.3 % Frequency Response30 Hz 15 kHz, 1.0 dB Stereo Separation45 dB at 1 kHz 30 dB at 100 Hz 10 kHz AM Tuning Range USA & Canadian models5301,710 kHz (10 kHz step

13、s) European & Australian models : 5221,611 kHz (9 kHz steps) Asian models5311,602 kHz (9 kHz steps) Usable Sensitivity30 V Image Rejection Ratio40 dB IF Rejection Ratio40 dB Signal-to-Noise Ratio40 dB Total Harmonic Distortion0.7 % SPECIFICATIONS : : : : : : : : : : : : : : : : : : : : : : : : : : :

14、 : : : : : : : : : : : : : : : : : : : : : : : : : : : RadioFans.CN 收音机爱 好者资料库 RDC-7 3 SERVICE PROCEDURE 1. Replacing the fuses 3. Safety-check out (Only U.S.A. model) After correcting the original service problem perform the follwing safety check before releasing the set to the customer Connect the

15、 insulating-resistance tester between the plug of power supply cord and terminal GND on the back panel. Specifications: More than 10Mohm at 500V REF.NO.PART NO. DESCRIPTION NOTE : : 120 V model only : Asian model only for 120V : European model only : Asian model only for 230V : 220V model only This

16、symbol located near the fuse indicates that the fuse used is show operating type, For continued protection against fire hazard, replace with same type fuse , For fuse rating, refer to the marking adjest to the symbol. Ce symbole indique que le fusible utilise est e lent. Pour une protection permanen

17、te, nutiliser que des fusibles de meme type. Ce demier est indique la qu le present symbol est apposre. This device employs a microprocessor to perform various functions and operations. If interference generated by an external power supply, radio wave, or other electrical souce results in accident w

18、hich causes the specified operations and functions to pperate abnormally. To perform a result, please follow the procesure below. 1. Turn teh Power switch to on. 2. Press and the hold down the VIDEO-1 button, then press the STANDBY/ON button. 2. After clear is displayed, the preset memory and each m

19、ode stored in the memory, such as surround, are initialized and will return to the factory setting 3. Press the STANDBY/ON button. 4. Disconnect the power supply cord. 2. To initialize the unit 4. Memory Preservation This unit does not require memory preservation batteries. A built-in memory power b

20、ack-up system preserves the contents of the memory during power failures and even when the unit is un-plugged. The unit must be plugged in order to charge the back-up system. The memory preservation period after the unit has been unplugged varies depending on climate and placement of the unit. On th

21、e average, memory contents are protected over a period of a few weeks after the last time the unit has been unplugged. This period is shorter when the unit is exposed to a highly humid climate. 5. Changing the AM band step When you change the band step, change the parts as shown below. To 10kHz To 9

22、kHz R7091 Short Open R7191 Open 10 kohms R7276 Short Open R7277 Short Open R7376 Open 10kohms R7377 Open 10 kohms R7091 R7191 100 Q7001 MAIN MICROPROCESSOR MAIN MICROPROCESSOR PC BOARD NAAR-6837 From soldering side SUB MICROPROCESSOR PC BOARD NADIS-6832 From soldering side Q7201 SUB MICROPROCESSOR S

23、7641 R7277 R7376 R7276 R7377 F9001 252163 ! 4A-UL/T-237, Fuse F9002 252074 ! 2A-SE-EAK, Fuse 6. Connection of computer When you change the program of microprocessor or control the unit by the computer, connect the cable RS232C of straight type between a computer and terminal RS232C on the rear panel

24、. 12345 6789 54321 9876 To the unitTo PC GNDGND 1 2 3 7 8 9 1 2 3 7 8 9 RadioFans.CN 收音机爱 好者资料库 RDC-7 4 Front panel facilities Display Here is an explanation of the controls and displays on the front panel of the RDC-7. Front door Front panel Front panel door Front panel display ALDOLBY DIGIT MPEG D

25、TS DOLBY PRO LOGIC VIDEO 213 DVD 4 5COMPONENT ANALO GDIGITAL 213 SLEEP INPUT Standby/On DisplayDVDVideo 1Video 2Video 3Video 4Video 5Tape 1Tape 2AMFMPhonoC DOpen/Close Zone 2()GRN Rec ( )RED OffOn Standby Master Volume On Power AV Controller RDC-7 Phones Clear AV Controller RDC-7 Digital format: The

26、 current input source is set for a digital format of Auto. Bass level: The current bass level is +2. Treble level: The current treble level is -2. Front panel Power After plugging in the power cord into the rear panel and wall outlet, pressing this button connects the RDC-7 to the AC mains and turns

27、 it on. Before turning on the power, make sure all cables are properly connected. Turning on the RDC-7 may cause a momentary power surge that might interfere with other electrical equip- ment on the same circuit. If this is a problem, plug the RDC-7 into a different electrical circuit. Standby/On Pr

28、essing this button while the main power is turned on the STANDBY indicator lights up and the front display turns off. Pressing it again returns it to the standby state. This state turns off the display, disables control functions, and turns off all outputs to the main zone (those for the remote zone

29、 remain available). On and Standby indicator Master Volume The MASTER VOLUME knob is used to control the volume for the main zone. The volume for the remote zone (Zone 2) is independent. Open/Close Press this button to open and close the front door that covers the lower buttons. Display The DISPLAY

30、button is used to display information about the current input source signal. Each time you press the display button, the screen changes to show you different information concerning the input signal. The screen changes as follows: Program format Sampling frequency Digital input Digital format Bass le

31、vel Treble level. If the input source signal does not have any information for a particular screen, then that screen will be skipped. Displaying the data of the current input source Each display is explained below. Program format: Front channelSurround channel Sampling frequency: Source signal48 kHz

32、 Sampling frequency Digital input: The current input source is set for digital input at OPT1. LFE(Low Frequency Effect) Input Source Buttons (DVD, VIDEO 15, TAPE 1 2, AM, FM, PHONO, and CD) and Indicators These buttons are used to select the input source for the main zone. When an input source is se

33、lected, the indica- tor will light in blue. To select the input source for the re- mote zone (Zone 2) or recording out (Rec Out), first press the Zone 2 or Rec Out button, and then the desired input source button. Zone 2/Rec Indicator For Zone 2, the indicator above the selected input source button

34、will light green. For recording, it will light red. Lower buttons in the front door Caution: The front door of the AV Controller is motorized. Use the open/close button to open or close the door. Manually opening or closing the door, or moving the AV Controller while holding the door, will cause the

35、 door to malfunction or break. Rec Out Press the Rec Out button to output to a recording compo- nent for recording purposes. After pressing the Rec Out button, press one of the input source selector buttons within 8 seconds to select the component to record to. When one is selected, the indicator ab

36、ove that button will light in red. To record from the same input source that you are using (that is selected for the main zone), press the Rec Out button twice in succession. Note: The Rec Out and Zone 2 buttons use the same circuit and therefore cannot be used at the same time. When Rec Out is sele

37、cted, nothing is output from Zone 2. Zone 2 The RDC-7 includes a second signal path separate from the main one that can be used for a remote zone (Zone 2) or for making recordings. By connecting an additional amplifier or other video equipment to the Zone 2 outputs, you can output to a separate room

38、 an input source that is different from that being used in the main room. This al- lows you to watch one program in one room while some- body else is watching a different program in another. Press the Zone 2 button to enable output to the ZONE 2 outputs. After pressing the Zone 2 button, press one o

39、f the input source selector buttons within 8 seconds to select the input source for the remote zone. When one is se- lected, the indicator above that button will light in green. RDC-7 5 Front panel facilities Memory This button only operates when FM or AM is selected as the input source. This button

40、 allows you to preset fre- quencies for stations when using the FM/AM tuner. You can preset up to 40 stations (or frequencies) to be used with the PRESET buttons. Menu, , , Enter, , , Exit These buttons are used with the On Screen Display (OSD) menu. They also perform the same functions as the OSD M

41、ENU, (upper edge of ENTER button), (lower edge of ENTER button), (left edge of ENTER button), (right edge of ENTER button), ENTER, and EXIT RETURN buttons on the remote controller. Menu: Press to bring up the OSD menu. Exit: Press to exit the OSD menu when at the Menu Screen, or move to one screen p

42、revious to the one that is displayed if at any other screen. and : When selecting items in the OSD Menu, press these buttons to move the on-screen cursor (or the highlighted portion) upward and downward. and : When setting parameters in the OSD menu, press these buttons to select parameter values or

43、 modes. Enter: Press to display the screen for the selected item in the OSD Menu. Note for European models: These buttons are also used to set programs and finish scans when performing a PTY or TP scan with the RDS broadcasts. PHONES This is a standard stereo jack for connecting stereo headphones. T

44、he audio for the front right and left speakers are sent to the headphone speakers. When the headphones are plugged in, the listening mode automatically changes to stereo and output to the speakers is stopped. Front panel display Listening mode or digital input format indicators Multi function displa

45、y Sleep indicator Input source format indicator Video display To use the same input source for the both the main and remote zones, press the Zone 2 button twice in succession. Note: The Rec Out and Zone 2 buttons use the same circuit and therefore cannot be used at the same time. when Zone 2 is sele

46、cted, the currently selected input source is output from the recording terminal. Off When not using either Rec Out or Zone 2, press that but- ton and then press the Off button to turn off the signal. If the Rec Out or Zone 2 signal is turned on and the con- nected component is not turned on, the electric signal will still be sent through the circuitry and the excess load may cause deterioration of the audio signal. DSP Press these buttons to scroll through the listen