Aiwa-CDC-R927M-Service-Manual 电路图 维修手册.pdf
《Aiwa-CDC-R927M-Service-Manual 电路图 维修手册.pdf》由会员分享,可在线阅读,更多相关《Aiwa-CDC-R927M-Service-Manual 电路图 维修手册.pdf(57页珍藏版)》请在收音机爱好者资料库上搜索。
1、SERVICE MANUAL DATA BASIC CD MECHANISM : BZG-3 CNFSTEREO CAR CD RECEIVER CDC-R927M S/M Code No. 09-026-458-9N1 YZ(ST) RadioFans.CN 收音机爱 好者资料库 -2- SPECIFICATION -1/1 RADIO SECTION (FM) Frequency Range:87.5 MHz - 108 MHz (50-KHz steps) Usable Sensitivity:12.7 dBf 50 dB Quieting Sensitivity:17.2 dBf IF
2、 Rejection:100 dB Frequency Response:30 Hz - 15,000 Hz S/N Ratio:67 dB Stereo Separation:35 dB at 1 kHz Alternate Channel Selectivity:98 dB Capture Ratio:3 dB (MW) Frequency Range:531 kHz - 1,602 kHz (9-KHz steps) Usable Sensitivity:30 V (30 dB) (LW) Frequency Range:144 kHz - 288 kHz (1-kHz/9-kHz st
3、eps) Usable Sensitivity:30 V (30 dB) CD SECTION Frequency Response:17 Hz - 20 kHz +0/-3 dB Dynamic Range:More than 92 dB Channel Separation:More than 60 dB S/N Ratio:More than 90 dB Wow/Flutter:Unmeasurable AUDIO SECTION Max. Power Output:45 W x 4 channels AUX IN input Input sensitivity (load impeda
4、nce) AUX IN: 300 mV (10 k) GENERAL Power-Supply Voltage:14.4 V (11 to 16 V allowable), DC, negative ground Load Impedance:4 Tone Control:Bass 10 dB at 100 Hz, Treble 10 dB at 10 kHz Preamp Output Voltage (load impedance): 2.2 V (10 k) Installed size:182 (W) x 53 (H) x 155 (D) mm CARD REMOTE CONTROL
5、Dimensions: Approx.33 (W) x 85 (H) x 7.5 (D) mm Weight: Approx.20 g (including battery) Specifications and external appearance are subject to change without notice due to product improvement. RadioFans.CN 收音机爱 好者资料库 -3- PROTECTION OF EYES FROM LASER BEAM DURING SERVICING -1/1 VAROITUS! Laiteen Kyttm
6、inen muulla kuin tss kyttohjeessa mainitulla tavalla saattaa altistaa kyt-tjn turvallisuusluokan 1 ylittvlle nkymttmlle lasersteilylle. VARNING! Om apparaten anvnds p annat stt n vad som specificeras i denna bruksanvising, kan anvndaren utsttas fr osynling laserstrlning, som verskrider grnsen fr las
7、erklass 1. Caution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. Advarsel:Usynling laserstling ved bning, nr sikkerhedsafbrydere er ude af funktion. Undg udsttelse for strling. CAUTION Use of controls or adjustments or performance of procedures other than those
8、 specified herein may result in hazardousradiation exposure. ATTENTION Lutilisation de commandes, rglages ou procdures autres que ceux spcifis peut entraner une dangereuse exposition aux radiations. ADVARSEL! Usynlig laserstling ved bning, nr sikkerhedsafbrydereer ude af funktion. Undg udsttelse for
9、 strling. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior. This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing. WARNING! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT
10、WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1 LASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT Precaution to replace O
11、ptical block (PICK720) 1) After the connection, remove solder shown in the right figure. Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode. PICK-UP ASSY. P.C.B Solder RadioFans.CN 收音
12、机爱 好者资料库 != ! SAFTY PARTS C= Components marked All components used on this model at the production line are shown in this service manual. However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for
13、 service and will be stocked at the spare parts centers. Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers. UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL -4- ACCESSORIES PARTS LIST -1/1 CDC-R927M YZSTF O AS
14、1001 8C-KC2-901-010 IB,YZ(9L)F R927M a O AS1002 8C-KCG-913-010 IB,INST YZ,YV (9L,R)F a O AS1003 87-B10-141-010 NUT,5 TYPE-2 a O AS1004 87-B10-143-010 UT1+5-15 W/O SLOT a O AS1005 87-B10-144-010 W,5.2-10-0.5 a O AS1006 87-B10-145-010 W-SPR,5.3-8.5-1.5 a O AS1007 8C-KCG-651-010 RC UNIT,CD1B a O AS1008
15、 8Z-KC1-231-110 HLDR,HALF -C a O AS1009 8Z-KC1-232-010 KEY,REMOVE -C a O AS1010 8Z-KC1-235-010 HLDR,REAR MTG a O AS1011 8Z-KC1-244-010 S-SCREW,5*6 TH+ TAPPING ST a O AS1012 8Z-KC1-250-010 S-SCREW,HEXAGON a -5- DISASSEMBLY INSTRUCTION - 1/2 DISASSMBLY PROCEDURE 1) Remove top and bottom cover. 2) Remo
16、ve CD mechanism. 3) Remove FFC. 4) Remove wire solder. 5) Remove the screw of MAIN BOARD. 6) Remove the connector of the motor. 7) Remove CABI BASE AROUND and remove the screw of FRAME SUB assy right and left. 8) Move FRONT PANEL assy. Notes Each FFC shoud be passed the bottom of SHAFT Assy. -6- 9)
17、Remove MOTOR assy. 10) Remove FRONT assy. 11) Remove Panel SW assy. (Extend FRAME SUB assy lightly and remove it at front side) 12) Remove SHAFT assy. (Remove the washer. See figure) Reassemble MOTOR assy at the position that is arranged with hole of GEAR CAM and hole of FRAME SUB assy like the figu
18、re) Put the tip of a lever Assy gear at between the marks of GEAR CAM and reassemble FRONT assy. (Extend FRAME SUB assy lightly.) Put GEAR CAM at the position that hole of FRAME SUB assy can be seen from the left and right side hole of GEAR CAM, and reassemble SHAFT assy. DISASSEMBLY INSTRUCTION - 1
19、/2 != ! SAFTY PARTS C= Components marked All components used on this model at the production line are shown in this service manual. However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for servi
20、ce and will be stocked at the spare parts centers. Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers. UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL -7- ELECTRICAL PARTS LIST - 1/10 CDC-R927M YZSTF CD O C 02
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Aiwa-CDC-R927M-Service-Manual 电路图 维修手册 Aiwa CDC R927M Service Manual 维修 手册
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf

