Aiwa-CDC-X204-Service-Manual 电路图 维修手册.pdf

《Aiwa-CDC-X204-Service-Manual 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Aiwa-CDC-X204-Service-Manual 电路图 维修手册.pdf（46页珍藏版）》请在收音机爱好者资料库上搜索。

1、1 Ver 1.0 2004. 01 Model Name Using Similar MechanismCDX-R3000/R3000T CD Drive Mechanism TypeMG-611XC-186/Q Optical Pick-up NameKSS1000E SERVICE MANUALUS Model Canadian Model CDC-X204/X304/X444 AEP Model UK Model CDC-R304/X304 East European Model CDC-X104EE CDC-R304/X104EE/X204/ X304/X444 CDC-X304:

2、US model/X444 AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION 23.2 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 5% total harmonic distortion. CDC-X204 AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL H

3、ARMONIC DISTORTION 22 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 5% total harmonic distortion. Tuner section FM Tuning rangeUS, Canadian Model: 87.5 107.9 MHz AEP, UK Model: 87.5 108 MHz CDC-X104EE: FM1/FM2: 87.5 108.0 MHz

4、 (at 50 kHz step) FM3: 65 74 MHz (at 30 kHz step) Antenna terminalExternal antenna connector Intermediate frequency10.7 MHz/450 kHz Usable sensitivity9 dBf Selectivity75 dB at 400 kHz Signal-to-noise ratio67 dB (stereo), 69 dB (mono) Harmonic distortion at 1 kHz 0.5% (stereo), 0.3% (mono) Separation

5、35 dB at 1 kHz Frequency response30 15,000 Hz AM (US, Canadian Model) Tuning range530 1,710 kHz Antenna terminalExternal antenna connector Intermediate frequency10.7 MHz/450 kHz Sensitivity30 V SPECIFICATIONS AM (CDC-X104EE) Tuning range531 1,602 kHz Antenna terminalExternal antenna connector Interm

6、ediate frequency10.7 MHz/450 kHz Sensitivity30 V MW/LW (AEP, UK Model) Tuning rangeMW: 531 1,602 kHz LW: 153 279 kHz Antenna terminalExternal antenna connector Intermediate frequency10.7 MHz/450 kHz SensitivityMW: 30 V LW: 40 V The tuner and CD sections have no adjustments. Sony Corporation e Vehicl

7、e Company Published by Sony Engineering Corporation 9-877-519-01 2004A04-1 2004. 01 Photo: CDC-R304 FM/AM COMPACT DISC PLAYER US, Canadian, East European model FM/MW/LW COMPACT DISC PLAYER AEP, UK model Continued on next page RadioFans.CN 收音机爱 好者资料库 2 CDC-R304/X104EE/X204/X304/X444 If the optical pi

8、ck-up block is defective, please replace the whole optical pick-up block. Never turn the semi-fixed resistor located at the side of optical pick-up block. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

9、 SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY

10、. ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES S

11、UPPLMENTS PUBLIS PAR SONY. SERVICE NOTES NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. Duri

12、ng repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to

13、be focused on the disc reflective surface by the objective lens in the optical pick- up block. Therefore, when checking the laser diode emission, ob- serve from more than 30 cm away from the objective lens. Notes on Chip Component Replacement Never reuse a disconnected chip component. Notice that th

14、e minus side of a tantalum capacitor may be dam- aged by heat. optical pick-up semi-fixed resistor US, Canadian model AEP, UK model CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. This compact disc play

15、er is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the exterior. This label is located on the bottom of the chassis. CD player section Signal-to-noise ratioUS, Canadian Model: 110 dB AEP, UK Model/CDC-X444: 120 dB Frequency response10 20,000 Hz Wow and flutter

16、Below measurable limit Power amplifier section OutputsSpeaker outputs (sure seal connectors) Speaker impedance4 8 ohms Maximum power output CDC-R304/X304/X444: 52 W 4 (at 4 ohms) CDC-X104EE/X204: 45 W 4 (at 4 ohms) General OutputsAudio outputs terminal (rear/sub switchable) Power antenna relay contr

17、ol terminal Power amplifier control terminal InputsTelephone ATT control terminal (AEP, UK Model/ CDC-X444) Antenna input terminal Tone controlsLow: 10 dB at 60 Hz (HIP-HOP) Mid: 10 dB at 1 kHz (HIP-HOP) High: 10 dB at 10 kHz (HIP-HOP) Power requirements12 V DC car battery (negative ground) Dimensio

18、nsApprox. 178 50 176 mm (7 1/8 2 7 in.) (w/h/d) Mounting dimensionsApprox. 182 53 161 mm (7 1/4 2 1/8 6 3/8 in.) (w/h/d) MassApprox. 1.2 kg (2 lb. 10 oz.) Supplied accessoriesParts for installation and connections (1 set) Front panel case (1) Card remote control RM-Z304 (CDC-X444) Design and specifi

19、cations are subject to change without notice. TEST DISCS This set can playback CD-R and CD-ROM discs. The following test discs should be used to check the capability: CD-R test disc TCD-R082LMT (Part No. J-2502-063-1) CD-RW test disc TCD-W082L (Part No. J-2502-063-2) RadioFans.CN 收音机爱 好者资料库 3 CDC-R3

20、04/X104EE/X204/X304/X444 z UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) : LEAD FREE MARK Unlea

21、ded solder has the following characteristics. Unleaded solder melts at a temperature about 40C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be

22、set to about 350C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins,

23、etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. SERVO BOARD CN1 J-2502-076-1 MAIN BOARD CN301 Notes on CD-R/CD-RW discs You can play CD-Rs (recordable CDs)/CD-RWs (rewritable CDs) designed for audio use on this unit. L

24、ook for these marks to distinguish CD-Rs/CD-RWs for audio use. These marks denote that a disc is not for audio use. Some CD-Rs/CD-RWs (depending on the equipment used for its recording or the condition of the disc) may not play on this unit. You cannot play a CD-R/CD-RW that is not finalized. A proc

25、ess necessary for a recorded CD-R/CD-RW disc to be played on the audio CD player. EXTENSION CABLE AND SERVICE POSITION When repairing or servicing this set, connect the jig (extension cable) as shown below. Connect the MAIN board (CN301) and the SERVO board (CN1) with the extension cable (Part No. J

26、-2502-076-1). RadioFans.CN 收音机爱 好者资料库 4 CDC-R304/X104EE/X204/X304/X444 TABLE OF CONTENTS 1. GENERAL Location of Controls. 5 Connections (US, Canadian Model). 6 Connections (AEP, UK Model) . 7 2. DISASSEMBLY 2-1. Sub Panel Assy . 9 2-2. CD Mechanism Block . 9 2-3. Main Board .10 2-4. Chassis (T) Sub

27、Assy . 10 2-5. Roller Arm Assy . 11 2-6. Chassis (OP) Assy . 11 2-7. Optical Pick-up . 12 2-8. SL Motor Assy (M902) . 12 2-9. LE Motor Assy (M903). 13 2-10. Servo Board.13 3. DIAGRAMS 3-1. IC Pin Descriptions .14 3-2. Block Diagram CD Section.18 3-3. Block Diagram Main Section.19 3-4. Block Diagram

28、Display Section.20 3-5. Circuit Boards Location .20 3-6. Note for Printed Wiring Boards and Schematic Diagrams. 21 3-7. Waveforms. 21 3-8. Printed Wiring Boards CD Mechanism Section.22 3-9. Schematic Diagram CD Mechanism Section.23 3-10. Schematic Diagram Main Section (1/2).24 3-11. Schematic Diagra

29、m Main Section (2/2).25 3-12. Printed Wiring Board Main Section . 26 3-13. Printed Wiring Boards Display Section . 27 3-14. Schematic Diagram Display Section. 28 3-15. IC Block Diagrams. 29 4. EXPLODED VIEWS 4-1. Main Section . 32 4-2. Front Panel Section .33 4-3. CD Mechanism Section (1) .34 4-4. C

30、D Mechanism Section (2) .35 4-5. CD Mechanism Section (3) .36 4-6. CD Mechanism Section (4) .37 5. ELECTRICAL PARTS LIST.38 5 CDC-R304/X104EE/X204/X304/X444 SECTION 1 GENERAL This section is extracted from instruction manual. LOCATION OF CONTROLS 6 CDC-R304/X104EE/X204/X304/X444 CONNECTIONS (US, Can

31、adian Model) 7 CDC-R304/X104EE/X204/X304/X444 CONNECTIONS (AEP, UK Model) 8 CDC-R304/X104EE/X204/X304/X444 SECTION 2 DISASSEMBLY Note : This set can be disassemble according to the following sequence. 2-1.SUB PANEL ASSY (Page 9) 2-2.CD MECHANISM BLOCK (Page 9) SET 2-3.MAIN BOARD (Page 10) 2-4.CHASSI

32、S (T) SUB ASSY (Page 10) 2-5.ROLLER ARM ASSY (Page 11) 2-6.CHASSIS (OP) ASSY (Page 11) 2-8.SL MOTOR ASSY (M902) (Page 12) 2-10. SERVO BOARD (Page 13) 2-7.OPTICAL PICK-UP (Page 12) 2-9.LE MOTOR ASSY (M903) (Page 13) 9 CDC-R304/X104EE/X204/X304/X444 2-2. CD MECHANISM BLOCK Note : Follow the disassembl

33、y procedure in the numerical order given. 2-1. SUB PANEL ASSY 2 two claws 3 two claws 4 sub panel assy 1 two screws (+PTT 2.6 x 6) 7 bracket (CD) 5 CD mechanism block 4 CN301 3 1screw (+PTT 2.6 x 6) 2screw (+PTT 2.6 x 6) 6two screws (+PTT 2.6 x 4) 10 CDC-R304/X104EE/X204/X304/X444 2-4. CHASSIS (T) S

34、UB ASSY 2-3. MAIN BOARD 1 three ground point screws (+PTT 2.6 x 6) 3 MAIN board 2 two screws (+PTT 2.6 x 6) insulating sheet 5 SENSOR board 6 chassis (T) sub assy 4 claw 3 claw 1 two screws (+P 1.7 x 2.2) 2 two screws (+P 1.7 x 2.2) 11 CDC-R304/X104EE/X204/X304/X444 2-5. ROLLER ARM ASSY 2-6. CHASSIS

35、 (OP) ASSY 3 washer (0.8-2.5) 4 worm wheel (RA) 5 roller arm assy 1 spring (RAL) 2 spring (RAR) 4 washer 0 coil spring (damper) 9 two coil springs (damper) qa chassis (OP) assy 5 gear (LE1) 1 CN2 lever (D) slider (R) 6 7 8 2 Remove the six solderings. 3 tension coil spring (KF) 12 CDC-R304/X104EE/X2

36、04/X304/X444 2-7. OPTICAL PICK-UP 2-8. SL MOTOR ASSY (M902) 1 tension coil spring (CHKG) 2 chucking arm sub assy 3 screw (+B 1.4 x 5) 4 rack (SL) 5 claw 6 main shaft 7 optical pick-up 1 screw (+P 1.4 x 1.8) 2 SL motor assy (M902) 13 CDC-R304/X104EE/X204/X304/X444 2-9. LE MOTOR ASSY (M903) 2-10. SERV

37、O BOARD 2 washer 4 qd 3 gear (LE1) 7 leaf spring (LE) 5 lever (D) bracket (LEM) slider (R) 6 screw (+P 1.7 x 2.2) 8 screw (+M 1.7 x 2.5) qa screw (+M 1.7 x 2.5) qf two toothed lock screws (+M 1.4 ) qs screw (+M 1.7 x 2.5) 9 bearing (LEB) 0 woam (LEB) assy qg LE motor assy (M903) 1 Remove the solderi

38、ng. 3 CN2 5 claw 6 SERVO board 4 toothed lock screw (M 1.7) 1 Remove the eight solderings. 2 Remove the three solderings. 14 CDC-R304/X104EE/X204/X304/X444 3-1. IC PIN DESCRIPTIONS IC1 PD63712GC-8EU-A (RF AMP, DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR) (SERVO BOARD) Pin No.Pin NameI/OPin Description 1

39、LDOLaser diode ON/OFF control signal output (L: laser OFF, H: laser ON) 2PDIDimmer monitor input from optical pick-up laser diode. 3PNINot used. (Fixed at L in this set) 4AVDDAnalog power supply pin (+3.3 V) 5DGNDGround 6RFOKORFOK signal output to system control IC. 7INTQOCD text pack synchronizatio

40、n signal output to system control IC. 8RSTICD reset signal input from system control IC. 9A0I Command/parameter discrimination signal input from system control IC. (L: command transmission, H: parameter transmission) 10STBIData strobe signal input from system control IC. 11SCKISerial clock input fro

41、m system control IC. 12SOOSerial data output to system control IC. 13SIISerial data input from system control IC. 14DVDDPower supply pin (+3.3 V) 15DAVDDD/A converter power supply (+) pin (+3.3 V) 16ROUTOAnalog audio signal output (R-ch) 17DAGNDGround 18REGCCapacitor connection pin for SCF regulator

42、. 19DAGNDGround 20LOUTOAnalog audio signal output (L-ch) 21DAVDDD/A converter power supply (+) pin (+3.3 V) 22XVDDPower supply pin (+3.3 V) 23XTALOMain system clock output (16.9344 MHz) 24XTALIMain system clock input (16.9344 MHz) 25XGNDGround 26DVDDPower supply pin (+3.3 V) 27C1D1/FZDONot used. (Op

43、en) 28C1D2/TZDONot used. (Open) 29C2D1/RMUTEOCD R-ch data zero detection signal output 30C2D2/LMUTEOCD L-ch data zero detection signal output 31C2D3/SHOCK/SBSYONot used. (Open) 32LOCK/FRONot used. (Open) 33WFCK/MIRRONot used. (Open) 34RFCK/HOLDONot used. (Open) 35PLCKONot used. (Open) 36C16MONot use

44、d. (Open) 37DGNDGround 38TXONot used. (Open) 39EMPH/RAMOVERONot used. (Open) 40FLAGONot used. (Open) 41DVDDPower supply pin (+3.3 V) 42LIMITINot used. (Fixed at L in this set) 43XTALENI Oscillation circuit ON/OFF control signal input (L: ON, H: OFF) (Fixed at L in this set) 44DGNDGround 45DININot used. (