Marantz-SR-6005-Service-Manual 电路图 维修手册.pdf

《Marantz-SR-6005-Service-Manual 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Marantz-SR-6005-Service-Manual 电路图 维修手册.pdf（189页珍藏版）》请在收音机爱好者资料库上搜索。

1、Service Manual Some illustrations using in this service manual are slightly different from the actual set. Please use this service manual with referring to the operating instructions without fail. For purposes of improvement, specifi cations and design are subject to change without notice. AV Surrou

2、nd Receiver SR6005 /N1SG/N1B/U1B/K1B SR6005 SR6005 S0159-1V02DM/DG1010Copyright 2010 D&M Holdings Inc. All rights reserved. WARNING: Violators will be prosecuted to the maximum extent possible. Ver. 2 Please refer to the MODIFICATION NOTICE. RadioFans.CN 收音机爱 好者资料库 2 MARANTZ DESIGN AND SERVICE Using

3、 superior design and selected high grade components, MARANTZ company has created the ultimate in stereo sound. Only original MARANTZ parts can insure that your MARANTZ product will continue to perform to the specifi cations for which it is famous. Parts for your MARANTZ equipment are generally avail

4、able to our National Marantz Subsidiary or Agent. ORDERING PARTS : Parts can be ordered either by mail or by Fax. In both cases, the correct part number has to be specifi ed. The following information must be supplied to eliminate delays in processing your order : 1. Complete address 2. Complete par

5、t numbers and quantities required 3. Description of parts 4. Model number for which part is required 5. Way of shipment 6. Signature : any order form or Fax. must be signed, otherwise such part order will be considered as null and void. In case of diffi culties, do not hesitate to contact the Techni

6、cal Department at above mentioned address. 091105DM/DG USA MARANTZ AMERICA, INC 100 CORPORATE DRIVE MAHWAH, NEW JERSEY 07430 USA EUROPE / TRADING D&M EUROPE B. V. P. O. BOX 8744, BUILDING SILVERPOINT BEEMDSTRAAT 11, 5653 MA EINDHOVEN THE NETHERLANDS PHONE : +31 - 40 - 2507844 FAX : +31 - 40 - 250786

7、0 KOREA D&M SALES AND MARKETING KOREA LTD. 2F,YEON BLDG., 88-5, BANPO-DONG, SEOCHO-GU, SEOUL KOREA PHONE : +82 - 2 - 715 - 9041 FAX : +82 - 2 - 715 - 9040 CANADA D&M Canada Inc. 5-505 APPLE CREEK BLVD. MARKHAM, ONTARIO L3R 5B1 CANADA PHONE : 905 - 415 - 9292 FAX : 905 - 475 - 4159 JAPAN D&M BUILDING

8、, 2-1 NISSHIN-CHO, KAWASAKI-KU, KAWASAKI-SHI, KANAGAWA, 210-8569 JAPAN D&M Holdings Inc. CHINA D&M SALES AND MARKETING SHANGHAI LTD. ROOM.808 SHANGHAI AIRPORT CITY TERMINAL NO.1600 NANJING (WEST) ROAD, SHANGHAI, CHINA. 200040 TEL : 021 - 6248 - 5151 FAX : 021 - 6248 - 4434 SHOCK, FIRE HAZARD SERVICE

9、 TEST : CAUTION : After servicing this appliance and prior to returning to customer, measure the resistance between either primary AC cord connector pins (with unit NOT connected to AC mains and its Power switch ON), and the face or Front Panel of product and controls and chassis bottom. Any resista

10、nce measurement less than 1 Megohms should cause unit to be repaired or corrected before AC power is applied, and verifi ed before it is return to the user/customer. Ref. UL Standard No. 60065. NOTE ON SAFETY : Symbol z Fire or electrical shock hazard. Only original parts should be used to replaced

11、any part marked with symbol z . Any other component substitution (other than original type), may increase risk of fi re or electrical shock hazard. 安全上注意： z部品、安全上重要部品。必指定部品番号部品使用下。 RadioFans.CN 收音机爱 好者资料库 3 SAFETY PRECAUTIONS The following check should be performed for the continued protection of th

12、e customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. if the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the p

13、ower cord is less than 460 kohms, the unit is defective. Be sure to test for leakage current with the AC plug in both polarities, in addition, in each power ON, OFF and STANDBY mode, if applicable. CAUTION Please heed the points listed below during servicing and inspection. Heed the cautions! Spots

14、requiring particular attention when servicing, such as the cabinet, parts, chassis,etc., have cautions indicated on labels. be sure to heed these causions and the cautions indicated in the handling instructions. Caution concerning electric shock! (1) An AC voltage is impressed on this set, so touchi

15、ng internal metal parts when the set is energized could cause electric shock. Take care to avoid electric shock, by for example using an isolating transformer and gloves when servicing while the set is energized, unplugging the power cord when replacing parts, etc. (2) Tere are high voltage parts in

16、side. Handle with extra care when the set is energized. Caution concerning disassembly and assembly! Through great care is taken when manufacturing parts from sheet metal, there may in some rare cases be burrs on the edges of parts which could cause injury if fi ngers are moved across them. Use glov

17、es to protect your hands. Only use designated parts! The sets parts have specific safety properties (fire resistance, voltage resistance, etc.). For replacement parts, be sure to use parts which have the same poroperties. In particular, for the important safety parts that are marked z on wiring diag

18、rams and parts lists, be sure to use the designated parts. Be sure to mount parts and arrange the wires as they were originally! For safety seasons, some parts use tape, tubes or other insulating materials, and some parts are mounted away from the surface of printed circuit boards. Care is also take

19、n with the positions of the wores omsode amd clamps are used to keep wires away from heating and high voltage parts, so be sure to set everything back as it was originally. Inspect for safety after servicing! Check that all screws, parts and wires removed or disconnected for servicing have been put

20、back in their original positions, inspect that no parts around the area that has been serviced have been negatively affected, conduct an inslation check on the external metal connectors and between the blades of the power plug, and otherwise check that safety is ensured. (Insulation check procedure)

21、 Unplug the power cord from the power outlet, disconnect the antenna, plugs, etc., and turn the power switch on. Using a 500V insulation resistance tester, check that the inplug and the externally exposed metal parts (antenna terminal, headphones terminal, input terminal, etc.) is 1M or greater. If

22、it is less, the set must be inspected and repaired. Many of the electric and structural parts used in the set have special safety properties. In most cases these properties are difficult to distinguish by sight, and using replacement parts with higher ratings (rated power and withstand voltage) does

23、 not necessarily guarantee that safety performance will be poreserved. Parts with safety properties are indicated as shown below on the wiring diagrams and parts lists is this service manual. Be sure to replace them with parts with the designated part number. (1) Schematic diagrams .Indicated by the

24、 z mark. (2) Parts lists .Indicated by the z mark. Using parts other than the designated parts could result in electric shock, fi res or other dangerous situations. CAUTION Concerning important safety parts RadioFans.CN 收音机爱 好者资料库 4 NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts marked with this symbol z

25、 have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the res

26、istance from chassis to either side of the power cord is less than 460 kohms, the unit is defective. WARNING: DO NOT return the unit to the customer until the problem is located and corrected. NOTICE: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM / M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD.

27、P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASURED AT NO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts for which nsp is indicated on this table cannot be supplied. When ordering of part, clearly indicate 1 and I (i) to avoid mis-supplying. Orderin

28、g part without stating its part number can not be supplied. Not including General-purpose Carbon Chip Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.) Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by the m

29、anufacturer. Not including General-purpose Carbon Film Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.) Part indicated with the mark is not illustrated in the exploded view. WARNING: 1. 2. 3. 4. 5. 6. Resistors RD:Carbon RC:Composition RS :Metal oxide film RW:w

30、inding RN:Metal film RK :Metal mixture P:Pulse-resistant type NL :Low noise type NB :Non-burning type FR :Fuse-resistor F:Lead wire forming 2B :1/8 W 2E :1/4 W 2H :1/2 W 3A :1 W 3D :2 W 3F :3 W 3H :5 W F:1% G:2% J:5% K:10% M :20% Ex.:RN Type 14K Shape and per- formance 2E Power 182 Resist- ance G Al

31、lowable error FR Others * Resistance 1800ohm=1.8kohm1 82 Indicates number of zeros after effective number. 2-digit effective number. 1.2ohm1 R2 2-digit effective number, decimal point indicated by R. 1-digit effective number. : Units: ohm Capacitors CE :Aluminum foil electrolytic CA :Aluminium solid

32、 electrolytic CS :Tantalum electrolytic CQ:Film CK :Ceramic CC:Ceramic CP :Oil CM:Mica CF :Metallized CH:Metallized HS :High stability type BP :Non-polar type HR:Ripple-resistant type DL :For change and discharge HF :For assuring high requency U:UL part C:CSA part W :UL-CSA part F:Lead wire forming

33、0J :6.3 V 1A :10 V 1C :16 V 1E :25 V 1V :35 V 1H :50 V 2A :100 V 2B :125 V 2C :160 V 2D :200 V 2E :250 V 2H :500 V 2J :630 V F:1% G:2% J:5% K:10% M :20% Z:80% :- 20% P:+100% C:0.25pF D:0.5pF =:Others Ex.:CE Type 04W Shape and per- formance 1H Dielectric strength 3R2 Capacity M Allowable error BP Oth

34、ers Units:F. 2200F2 22 Indicates number of zeros after effective number. 2-digit effective number. Units:F. 2.2F2 R2 2-digit effective number, decimal point indicated by R 1-digit effective number. *Capacity (electrolyte only) When the dielectric strength is indicated in AC,AC is included after the

35、dieelectric strength value. *Capacity (except electrolyte) Units:pF 2200pF=0.0022F2 22 Indicates number of zeros after efective number. (More than 2) 2-digit effective number. Units:pF 220pF2 21 2-digit effective number. Indicates number of zeros after effective numver. (0 or 1) NOTE FOR PARTS LIST

36、5 TECHNICAL SPECIFICATIONS n Audio Section Power amplifi er Rated output : Front : 110 W + 110 W (8 , 20 Hz 20 kHz with 0.08 % T.H.D.) 190 W + 190 W (6 , 1 kHz with 10 % T.H.D.) Center : 110 W (8 , 20 Hz 20 kHz with 0.08 % T.H.D.) 190 W (6 , 1 kHz with 10 % T.H.D.) Surround : 110 W + 110 W (8 , 20 H

37、z 20 kHz with 0.08 % T.H.D.) 190 W + 190 W (6 , 1 kHz with 10 % T.H.D.) Surround Back : 110 W + 110 W (8 , 20 Hz 20 kHz with 0.08 % T.H.D.) 190 W + 190 W (6 , 1 kHz with 10 % T.H.D.) Output connectors : 6 8 (SPEAKER A + B : 8 ) Analog Input sensitivity/Input impedance : 175 mV/50 k Frequency respons

38、e : 10 Hz 100 kHz 3 dB (Source Direct mode) S/N : 98 dB (IHFA weighted, Source Direct mode) n Video Section Standard video connectors Input/output level and impedance : 1 Vp-p, 75 Frequency response : 5 Hz 10 MHz +1, 3 dB Standard video connectors Input/output level and impedance : Y (brightness) si

39、gnal 1 Vp-p, 75 PB / CB signal 0.7 Vp-p, 75 PR / CR signal 0.7 Vp-p, 75 Frequency response : 5 Hz 60 MHz +0, 3 dB n Tuner section FM(Note: V at 75 , 0 dBf = 1 x 1015 W) Receiving Range (for U) : FM 87.5 MHz 107.9 MHz AM520 kHz 1710 kHz Receiving Range (for N,K) : FM 87.5 MHz 108.0 MHz AM522 kHz 1611

40、 kHz Usable Sensitivity : FM1.2 V (12.8 dBf) AM18 V 50 dB Quieting Sensitivity (for U) : FMMONO 2.8 V (20.2 dBf) 50 dB Quieting Sensitivity (for N,K) : FMMONO 2.0 V (17.3 dBf) STEREO 42 V (34.5 dBf) S/N (IHF-A) : FMMONO 70 dB STEREO 67 dB Total harmonic Distortion (at 1 kHz) (for U) : FMMONO 0.7 % S

41、TEREO 1.0 % Total harmonic Distortion (at 1 kHz) (for N,K) : FMMONO 0.3 % STEREO 0.7 % n General Power supply (for U) : AC 120 V, 60 Hz Power supply (for K) : AC 220 V, 50 Hz Power supply (for N) : AC 230 V, 50 Hz Power consumption : 650 W 0.2 W (Standby) 3 W (CEC standby) Maximum external dimension

42、s : 440 (W) x 161 (H) x 389 (D) mm Weight : 11.8 kg n Remote Control Unit (RC011SR) Batteries : R03/AAA Type (two batteries) DIMENSION 348.517.522.5 389 30.58630.0 53.5245 440 146.5 344 214.564.0 14.5 161 6 CAUTION IN SERVICING Initializing AV SURROUND RECEIVER AV SURROUND RECEIVER initialization sh

43、ould be performed when the com, peripheral parts of com, and Digital P.W.B. are replaced. 1. Turn off the power using ON/STANDBY button. 2. Press ON/STANDBY button while simultaneously pressing SURR.MODE and AUTO buttons. 3. Check that the entire display is fl ashing with an interval of about 1 seco

44、nd, and release your fi ngers from the 2 buttons and the microprocessor will be initialized. Service Jigs When you repair the printing board, you can use the following JIG (Extension cable kit). Please order to marantz Offi cial Service Distributor in your region if necessary. 8U-110084S : EXTENSION

45、 UNIT KIT : 1 Set (Refer to JIG FOR SERVICING.) Note: If step 3 does not work, start over from step 1. All user settings will be lost and this factory setting will be recovered when this initialization mode. So make sure to memorize your setting for restoring after the initialization. ON/STANDBY SUR

46、R.MODE AUTO DISASSEMBLY Disassemble in order of the arrow of the fi gure of following fl ow. In the case of the re-assembling, assemble it in order of the reverse of the following fl ow. In the case of the re-assembling, observe attention of assembling it. If wire bundles are untied or moved to perf

47、orm adjustment or parts replacement etc., be sure to rearrange them neatly as they were originally bundled or placed afterward. Otherwise, incorrect arrangement can be a cause of noise generation. FRONT PANEL ASSY Refer to DISASSEMBLY 1. FRONT PANEL ASSY and EXPLODED VIEW PCB FRONT (Ref. No. of EXPL

48、ODED VIEW : 26) PCB USB (Ref. No. of EXPLODED VIEW : 59-1) PCB PCB MIC_H/P (Ref. No. of EXPLODED VIEW : 59-2) RADIATOR ASSY Refer to DISASSEMBLY 2. RADIATOR ASSY and EXPLODED VIEW PCB 7CH_AMP ASSY (Ref. No. of EXPLODED VIEW : 50) PCB GUIDE_L (Ref. No. of EXPLODED VIEW : 60) PCB H/S GUIDE (Ref. No. o

49、f EXPLODED VIEW : 61) PCB GUIDE_R (Ref. No. of EXPLODED VIEW : 62) PCB REG CNT/PCB REG Refer to DISASSEMBLY 3. PCB REG CNT/PCB REG and EXPLODED VIEW PCB REG (Ref. No. of EXPLODED VIEW : 53) PCB REG_CNT (Ref. No. of EXPLODED VIEW : 54) CABINET TOP HDMI UNIT ASSY Refer to DISASSEMBLY 4. HDMI UNIT ASSY and EXPLODED VIEW PCB FRONT_CNT (Ref. No. of EXPLODED VIEW : 55) PCB SIDE_CNT (Ref. No. of EXPLODED VIEW : 56) PCB RS232 (Ref. No. of EXPLODED VIEW : 57) PCB SIRIUS (Ref. No. of EXPLODE