Rotel-RSX-03-OM 电路图 维修手册.pdf

《Rotel-RSX-03-OM 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Rotel-RSX-03-OM 电路图 维修手册.pdf（44页珍藏版）》请在收音机爱好者资料库上搜索。

1、Owners manual RSX-03 Surround Sound Receiver STANDBY BAND RSX-03 TUNING VIDEO2PHONO 2CH VIDEO1 MULTI INPUT TAPE DSP VIDEO3 MUTE VIDEO4 REC TUNER DTS Neo:6 CD DOLBY PLII/3ST RadioFans.CN 收音机爱 好者资料库 This symbol means that this unit is double insulated. An earth or ground connection is not required. Ro

2、tel products are designed to comply with international directives on the Re- striction of Hazardous Substances (RoHS) in electrical and electronic equipment and the disposal of Waste Electrical and Electronic Equipment (WEEE). The crossed wheelie bin symbol indicates compliance and that the products

3、 must be appropriately recycled or processed in accordance with these directives. RadioFans.CN 收音机爱 好者资料库 Notice The COMPUTER I/O connection should be handled by authorized person only. FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, p

4、ursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer- ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in ac- cordance with the instruction, may

5、 cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a par- ticular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the us

6、er is encouraged to try to correct the inter- ference by one or more of the following measures: Reorient or relocate the receiving antenna.(TV, radio, etc.) Increase the separation between the equipment and receiver Connect the equipment to an outlet on circuit different from that to which the recei

7、ver is connected. Consult the dealer or an experienced radio/TV technician for addi- tional help. Caution This device complies with part 15 of the FCC Rules operation is subject to the following to conditions: (1) This device may not cause harmful interference, and (2) this device must accept any in

8、terference received, including interference that may cause undesired operation. NOTE TO CATV SYSTEM INSTALLER: Call the CATV system or antenna installers attention to Article 820-40 of the NEC. This provides guidelines for proper grounding and, in particular, specifi es that the cable ground shall b

9、e connected to the grounding system of the building, as close to the point of cable entry as practical. See installation diagram. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

10、provide reasonable protection against interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause interference to radio or TV communications. There is no guarantee that inter

11、ference will not occur in a particular in- stallation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, try to correct the interference by one or more of the following measures: Reorient or relocate the receiving

12、 antenna. Increase the separation between the unit and the television tuner. Connect the unit to an AC power outlet on a different electrical cir- cuit. Consult your authorized Rotel retailer for assistance. Important Safety Instructions WARNING: There are no user serviceable parts inside. Refer all

13、 servic- ing to qualifi ed service personnel. WARNING: To reduce the risk of fi re or electric shock, do not expose the unit to moisture or water. Do not expose the unit to dripping or splash- ing. Do not place objects fi lled with liquids, such as vases, on the unit. Do not allow foreign objects to

14、 get into the enclosure. If the unit is exposed to moisture, or a foreign object gets into the enclosure, immediately dis- connect the power cord from the wall. Take the unit to a qualifi ed service person for inspection and necessary repairs. Read all the instructions before connecting or operating

15、 the component. Keep this manual so you can refer to these safety instructions. Heed all warnings and safety information in these instructions and on the product itself. Follow all operating instructions. Clean the enclosure only with a dry cloth or a vacuum cleaner. Do not use this unit near water.

16、 You must allow a minimum 10 cm or 4 inches of unobstructed clearance around the unit. Do not place the unit on a bed, sofa, rug, or similar surface that could block the ventilation openings. If the unit is placed in a bookcase or cabinet, there must be ventilation of the cabinet to allow proper coo

17、ling. Keep the component away from radiators, heat registers, stoves, or any other appliance that produces heat. The unit must be connected to a power supply only of the type and voltage specifi ed on the rear panel. (USA: 120 V/60Hz, EC: 230V/50Hz) Connect the component to the power outlet only wit

18、h the supplied power supply cable or an exact equivalent. Do not modify the supplied cable. A polarized plug has two blades, with one wider than the other. A grounding plug has two blades plus a third grounding prong. These are provided for your safety. Do not defeat grounding and/or polarization sa

19、fety provisions. If the supplied plug does not fi t your outlet, please consult an electrician for replacement of the obsolete outlet. Do not use extension cords. The main plug of the power cordset is a disconnect device of the appa- ratus. In order to completely disconnect the apparatus from the su

20、pply mains, the main plug of the power cordset should be unplugged from the mains (AC) outlet. The stand-by LED indicator will not be lit up to show the power cord is unplugged. Do not route the power cord where it will be crushed, pinched, bent, ex- posed to heat, or damaged in any way. Pay particu

21、lar attention to the power cord at the plug and where the cord exits the back of the unit. The power cord should be unplugged from the wall outlet during a lightning storm or if the unit is to be left unused for a long period of time. Use only accessories specifi ed by the manufacturer. Use only wit

22、h a cart, stand, rack, bracket or shelf system recommended by Rotel. Use caution when moving the unit in a stand or rack to avoid injury from a tip-over. Use Class 2 wiring for speaker connections to ensure proper installation and minimize the risk of electrical shock. Immediately stop using the com

23、ponent and have it inspected and/or ser- viced by a qualifi ed service agency if: The power supply cord or plug has been damaged. Objects have fallen or liquid has been spilled into the unit. The unit has been exposed to rain. The unit shows signs of improper operation The unit has been dropped or d

24、amaged in any way WARNING: The master power switch is located on the rear panel. The unit must be located in the open area allowing unobstructed access to the main power switch. RadioFans.CN 收音机爱 好者资料库 4RSX-03 Surround Sound Receiver 1: Controls and Connections OFF ON POWER STANDBY BAND RSX-03 TUNIN

25、G VIDEO2PHONO 2CH VIDEO1 MULTI INPUT TAPE DSP VIDEO3 MUTE VIDEO4 REC TUNER DTS Neo:6 CD DOLBY PLII/3ST DIGITAL INPUT Y PR PB 21 2 1 L R L R 1 35 5English 2: RR-1060 Remote 123 456 789 +100X CM SR ENT FRQ DIRECT MENUGUIDE TUNEPRESET FM MONOBAND CTR SUBSUR SEARCH-SEARCH+ OSD ONOFF SMTMUTE CHVOL POWER

26、SMART MEM AUDCDTUNTAPEEXT V1V2V3V4V5 DEVICE / INPUT RR-1060 LIGHT DVD RESUME REPEATSLOWGOTOA - B INPUT 1INPUT 2RECORDTV/VCRINPUT 3 ASPECTDISPOUTPUTPOPPIP 123 456 789 +100X ONOFF SMTMUTE CM SR ENT FRQ DIRECT MENUGUIDE TUNEPRESET FM MONOBAND CTR SUBSUR SEARCH-SEARCH+ OSD CD DISC2DISC1DISC3DISC4DISC5 P

27、ROGRANDOM REPEATDISC-DISC+ DISPLAYAUDIOZOOMSBTITLEANGLE DISPTAPE2PHONOTONED-SLT EQDYNRECZONESUR+ 2CHPL M5CH7CHPL C CHVOL POWER SMART MEM DIGESTOPENP-SCANTITLE SCANPTYP-TUNTPTA POWERSETUP 6RSX-03 Surround Sound Receiver 3: Connecting the Speakers SUBWOOFER INPUT OFF ON POWER DIGITAL INPUT Y PR PB 21

28、2 1 L R L R 7English 4: Connecting the TV 5: Connecting Cable, Satellite, or HDTV OFF ON POWER DIGITAL INPUT Y PR PB 21 2 1 L R L R OFF ON POWER DIGITAL INPUT Y PR PB 21 2 1 L R L R 8RSX-03 Surround Sound Receiver 6: Connecting a VCR 7: Connecting a CD Player/CDR Recorder and Turntable OFF ON POWER

29、DIGITAL INPUT Y PR PB 21 2 1 L R L R OFF ON POWER DIGITAL INPUT Y PR PB 21 2 1 L R L R 9English 8: Connecting an Audio Recorder 9: Connecting a DVD Player OFF ON POWER DIGITAL INPUT Y PR PB 21 2 1 L R L R OFF ON POWER DIGITAL INPUT Y PR PB 21 2 1 L R L R 10RSX-03 Surround Sound Receiver 11: Connecti

30、ng AM and FM antennae 10: Connecting a DVD-A or SACD Player OFF ON POWER DIGITAL INPUT Y PR PB 21 2 1 L R L R OFF ON POWER DIGITAL INPUT Y PR PB 21 2 1 L R L R 11English 12: On-Screen Menus 12RSX-03 Surround Sound Receiver Contents Boxed numbers refer to RSX-03 illustration. Boxed letters refer to R

31、R-1060 illustration. Important Safety Instructions .3 1: Controls and Connections .4 2: RR-1060 Remote .5 3: Connecting the Speakers .6 4: Connecting the TV .7 5: Connecting Cable, Satellite, or HDTV .7 6: Connecting a VCR .8 7: Connecting a CD Player/CDR Recorder and Turntable .8 8: Connecting an A

32、udio Recorder .9 9: Connecting a DVD Player .9 10: Connecting a DVD-A or SACD Player .10 11: Connecting AM and FM antennae .10 12: On-Screen Menus .11 About Rotel .14 Getting Started .14 Key Features .14 Unpacking .14 Placement .14 CONNECTIONS 15 Analog Audio Inputs however, S-Video connections prov

33、ide better picture quality. Component Video con- nections are required for HDTV or progressive scanned DVD video. Consider the following for your system confi guration: On Screen Display: The RSX-03 OSD menus are available on the TV only with com- posite video or S-Video connections from the TV MONI

34、TOR outputs to the TV set. NOTE: When using a progressive scan or 1080i video signal, the TV monitor cannot display the OSD menus. Many digital HDTV monitors adjust scan rates and other video parameters depending on the type of input connection. You may wish to make multiple connections between the

35、RSX-03 and the TV monitor, switching inputs on the TV to take advantage of these features. VIDEO 14 Composite Video Inputs Four inputs accepts standard composite video signals from source components using stan- dard 75 ohm RCA video cables. COMPOSITE Video Output An RCA jack, labeled COMPOSITE OUT,

36、sends a composite video signal for recording to a VCR or other recording device. NOTE: The RSX-03 cannot convert S-Video or Component Video to composite video. There- fore, only signals from the composite video inputs are available at these outputs. VIDEO 14 S-Video Inputs Four inputs, labeled S-VID

37、EO IN 14 ac- cept S-Video input signals from source com- ponents. S-VIDEO Video Output An S-VIDEO jack, labeled S-VIDEO OUT, sends an S-Video signal for recording to a VCR or other recording device. NOTE: The RSX-03 cannot convert composite video or Component Video signals to S-Vid- eo. Only signals

38、 received at the S-Video in- puts are available at these outputs. VIDEO 12 Component Video Inputs Component Video connections split the video into three signals luminance (Y) and chro- minance (CBPB and CRPR) signals, allowing delivery of a reference quality picture with high defi nition signals. Co

39、mponent Video connections should be used for progressive scan DVD players and high-defi nition televi- sion receivers. Each of these signals is car- ried by a separate 75 ohm video cable with RCA connectors. Two sets of inputs, labeled COMPONENT VIDEO IN 12 accept Component video signals from source

40、 components. TV Monitor Outputs The TV MONITOR outputs of the RSX-03 send the video signal to your TV monitor. Three types of video output connections are provided RCA composite video, S-Video, and Component Video. The composite video output only sends signals from composite video inputs to the TV m

41、onitor. The S-Video output only sends signals from S-Video video inputs to the TV. The Component Video outputs only send signals from Compo- nent Video source inputs to the TV. If you have connected all of your source com- ponents with the same type of connection, then you only need to make one conn

42、ection from the RSX-03 to the TV monitor, using that same type of connection. If you have a mix- ture of composite video, S-Video, and Com- ponent Video components, you will need to make multiple connections from the RSX-03 to the TV monitor. Digital Audio Input oth- erwise the RSX-03 will not be ab

43、le to decode these formats. Digital Inputs The RSX-03 accepts digital inputs from source components such as CD players, satellite TV tuners, and DVD players. The built-in digital processor senses the correct digital sampling rate and decodes the signal. There are four digital inputs on the rear pane

44、l, two coaxial and two optical. These digital inputs can be assigned to any of the input sources using the INPUT SETUP screen during the setup process. For example, you can as- sign the COAXIAL 1 digital input connector to the VIDEO 1 source and the OPTICAL 2 digital input to the VIDEO 3 source. NOT

45、E: When using digital connections, you should also make the analog audio input connections described previously. The analog connection is necessary to record to an ana- log recorder in some circumstances. Digital Outputs The RSX-03 has two digital outputs (one co- axial and one optical) to send the digital sig- nal from any of the digital inputs to a digital recorder or o