Rotel-RDV-1040-OM 电路图 维修手册.pdf

《Rotel-RDV-1040-OM 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Rotel-RDV-1040-OM 电路图 维修手册.pdf（30页珍藏版）》请在收音机爱好者资料库上搜索。

1、The Rotel Co. Ltd. 10-10 Shinsen-Cho Shibuya-Ku Tokyo 150-0045 Japan Phone: +81 3-5458-5325 Fax: +81 3-5458-5310 Rotel of America 54 Concord Street North Reading, MA 01864-2699 USA Phone: +1 978-664-3820 Fax: +1 978-664-4109 Rotel Europe Dale Road Worthing, West Sussex BN11 2BH England Phone: +44 (0

2、)1903 221 600 Fax: +44 (0)1903 221 525 Rotel Deutschland Kleine Heide 12 D-33790 Halle/Westf. Germany Phone: +49 05201-87170 Fax: +49 05201-73370 2 RDV-1040 DVD Player RDV-1040 DVD Player Owners Manual 082 OMRDV-1040 120103 English CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE

3、 SLOT. INSERT FULLY. APPLICABLE FOR USA, CANADA OR WHERE APPROVED FOR THE USAGE ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU AU FOND. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE

4、THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Important Safety Instructions WARNING: There are no user serviceable parts inside. Refer all servicing to qualified service personnel. WARNING: To reduce the risk of fire

5、 or electric shock, do not expose the unit to moisture or water. Do not allow foreign objects to get into the enclosure. If the unit is exposed to moisture, or a foreign object gets into the enclosure, immedi- ately disconnect the power cord from the wall. Take the unit to a qualified ser- vice pers

6、on for inspection and necessary repairs. Read all the instructions before connecting or operating the component. Keep this manual so you can refer to these safety instructions. Heed all warnings and safety information in these instructions and on the product itself. Fol- low all operating instructio

7、ns. Clean the enclosure only with a dry cloth or a vacuum cleaner. Do not use benzene, thinner or other organic solvents and disinfectants. These may cause deformation or discoloring. You must allow 15 cm (6 inches) of clearance behind, 3 cm (1.25 inches) to the sides and 5 cm (2 inches) above the u

8、nit. Do not place the unit on a bed, sofa, rug, or similar surface that could block the ventilation slots. If the component is placed in a bookcase or cabinet, there must be ventilation of the cabinet to allow proper cooling. Keep the component away from radiators, heat registers, stoves, or any oth

9、er appliance that produces heat. The unit must be connected to a power supply only of the type and voltage specified on the rear panel of the unit. Connect the component to the power outlet only with the supplied power supply cable or an exact equivalent. Do not modify the supplied cable in any way.

10、 Do not attempt to defeat grounding and/or polarization provisions. Do not use extension cords. Do not route the power cord where it will be crushed, pinched, bent at severe angles, exposed to heat, or damaged in any way. Pay particular attention to the power cord at the plug and where it exits the

11、back of the unit. The power cord should be unplugged from the wall outlet if the unit is to be left unused for a long period of time. Immediately stop using the component and have it inspected and/or serviced by a qualified service agency if: The power supply cord or plug has been damaged. Objects h

12、ave fallen or liquid has been spilled into the unit. The unit has been exposed to rain. The unit shows signs of improper operation The unit has been dropped or damaged in any way Place the unit on a fixed, level surface strong enough to support its weight. Do not place it on a moveable cart that cou

13、ld tip over. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec- tion against harmful interference in a residential installation. This equipment gene rates, uses

14、 and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio commu- nications. However, there is no guarantee that interference will not occur in a particular instal- lation. If this equipment does cause harmful i

15、nterference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to cor- rect the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment a

16、nd receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. IMPORTANT FOR LASER PRODUCTS 1. CLASS 1 LASER PRODUCT 2. DANGER: Visible laser radiation when open and interlock f

17、ailed or bypassed. Avoid direct exposure to beam. 3. CAUTION: Do not open the top cover. There are no user serviceable parts inside the player; leave all servicing to qualified service personnel. WARNING! To reduce the risk of electrical shock, fires, etc.: 1. Do not remove screws, covers or cabinet

18、. 2. Do not expose the unit to rain or moisture. 3. Do not touch the power cord or plug with wet hands. RadioFans.CN 收音机爱 好者资料库 The Rotel Co. Ltd. 10-10 Shinsen-Cho Shibuya-Ku Tokyo 150-0045 Japan Phone: +81 3-5458-5325 Fax: +81 3-5458-5310 Rotel of America 54 Concord Street North Reading, MA 01864-

19、2699 USA Phone: +1 978-664-3820 Fax: +1 978-664-4109 Rotel Europe Dale Road Worthing, West Sussex BN11 2BH England Phone: +44 (0)1903 221 600 Fax: +44 (0)1903 221 525 Rotel Deutschland Kleine Heide 12 D-33790 Halle/Westf. Germany Phone: +49 05201-87170 Fax: +49 05201-73370 2 RDV-1040 DVD Player RDV-

20、1040 DVD Player Owners Manual 082 OMRDV-1040 120103 English CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT. INSERT FULLY. APPLICABLE FOR USA, CANADA OR WHERE APPROVED FOR THE USAGE ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE D

21、ANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU AU FOND. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Important Safety Instructions WARNING: The

22、re are no user serviceable parts inside. Refer all servicing to qualified service personnel. WARNING: To reduce the risk of fire or electric shock, do not expose the unit to moisture or water. Do not allow foreign objects to get into the enclosure. If the unit is exposed to moisture, or a foreign ob

23、ject gets into the enclosure, immedi- ately disconnect the power cord from the wall. Take the unit to a qualified ser- vice person for inspection and necessary repairs. Read all the instructions before connecting or operating the component. Keep this manual so you can refer to these safety instructi

24、ons. Heed all warnings and safety information in these instructions and on the product itself. Fol- low all operating instructions. Clean the enclosure only with a dry cloth or a vacuum cleaner. Do not use benzene, thinner or other organic solvents and disinfectants. These may cause deformation or d

25、iscoloring. You must allow 15 cm (6 inches) of clearance behind, 3 cm (1.25 inches) to the sides and 5 cm (2 inches) above the unit. Do not place the unit on a bed, sofa, rug, or similar surface that could block the ventilation slots. If the component is placed in a bookcase or cabinet, there must b

26、e ventilation of the cabinet to allow proper cooling. Keep the component away from radiators, heat registers, stoves, or any other appliance that produces heat. The unit must be connected to a power supply only of the type and voltage specified on the rear panel of the unit. Connect the component to

27、 the power outlet only with the supplied power supply cable or an exact equivalent. Do not modify the supplied cable in any way. Do not attempt to defeat grounding and/or polarization provisions. Do not use extension cords. Do not route the power cord where it will be crushed, pinched, bent at sever

28、e angles, exposed to heat, or damaged in any way. Pay particular attention to the power cord at the plug and where it exits the back of the unit. The power cord should be unplugged from the wall outlet if the unit is to be left unused for a long period of time. Immediately stop using the component a

29、nd have it inspected and/or serviced by a qualified service agency if: The power supply cord or plug has been damaged. Objects have fallen or liquid has been spilled into the unit. The unit has been exposed to rain. The unit shows signs of improper operation The unit has been dropped or damaged in a

30、ny way Place the unit on a fixed, level surface strong enough to support its weight. Do not place it on a moveable cart that could tip over. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designe

31、d to provide reasonable protec- tion against harmful interference in a residential installation. This equipment gene rates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio commu- nications. Howeve

32、r, there is no guarantee that interference will not occur in a particular instal- lation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to cor- rect the interference by on

33、e or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technic

34、ian for help. IMPORTANT FOR LASER PRODUCTS 1. CLASS 1 LASER PRODUCT 2. DANGER: Visible laser radiation when open and interlock failed or bypassed. Avoid direct exposure to beam. 3. CAUTION: Do not open the top cover. There are no user serviceable parts inside the player; leave all servicing to quali

35、fied service personnel. WARNING! To reduce the risk of electrical shock, fires, etc.: 1. Do not remove screws, covers or cabinet. 2. Do not expose the unit to rain or moisture. 3. Do not touch the power cord or plug with wet hands. RadioFans.CN 收音机爱 好者资料库 34RDV-1040 DVD Player#English 1 2 3 4 5 TV /

36、 DVD switch OPEN/CLOSE button REPEAT button Numeric buttons SUB TITLE button ANGLE button TITLE / GROUP button / PREVIOUS button (STOP) / CLEAR button / SLOW button TOP MENU button VOLUME / CURSOR button CHANNEL / CURSOR button CHOICE button 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 3

37、4 Infrared output window DVD POWER button TV POWER button RETURN button DIMMER button VSS button +10 / MUTING button TV/VIDEO / CANCEL button AUDIO / fs/RATE button ZOOM button VFP / PROG SCAN button / NEXT button (PAUSE) button (PLAY)/ SELECT button / SLOW + button MENU button CHANNEL + / CURSOR bu

38、tton VOLUME + / CURSOR button ON SCREEN button ENTER button 6 7 8 9 10 11 12 13 14 Figure 1: RR-DV96 Remote Control 1 TV/DVD switch Switches the RDV-1040 between TV control mode and the DVD player control mode. 2OPEN/CLOSE button Opens and closes the disc tray. 3Repeat button Switches the RDV-1040 a

39、mong “no repeat” mode, “repeat 1” mode and to “repeat all” mode. 4Numeric buttons In DVD/CD mode use these to select a title or track number, to enter a time for the Time search. In TV mode they are used to select a TV channel. 5SUBTITLE button Used to activate the on-screen subtitle selection displ

40、ay and to turn the subtitle on or off (for DVD VIDEO). 6ANGLE button Changes camera angles during playback of a DVD VIDEO disc containing multiple camera angles. 7TITLE/GROUP button Displays the title menu of a DVD Video disc on the TV screen. Group function not used. 8 /PREVIOUS button Skips back a

41、 chapter, title or track. Also used for the page selection of a menu screen (for DVD VIDEO/Video CD). Holding down this button dur- ing playback rapidly scans to earlier scenes. 9 (STOP)/CLEAR button Stops playback. Also used to erase all the pro- grammed tracks for the program play. 10/SLOW button

42、During playback lets you reverse disc play at 1.5 to 60 times normal speed. When disc play is paused press to reverse disc play at 1/2 to 1/32 normal speed. 11TOP MENU button Press to display a menu to select specific scenes on a disc. 12VOLUME /CURSOR ? Button When in TV mode press to reduce volume

43、. When in DVD mode press to select an item from a menu or on-screen display, or to change the setting of an item in the on-screen display. 13CHANNEL /CURSOR ? Button When in TV mode press to go to a lower chan- nel. When in DVD mode press to select an item from a menu or on-screen display, or to cha

44、nge the setting of an item in the on-screen display. 14CHOICE button Displays the DVD set-up menu. Is also used when selecting parental lock settings 15Infrared signal output window Point this toward the remote sensor on the front panel when pressing buttons. 16DVD POWER button 17TV POWER button Pre

45、ss to turn the RDV-1040 or your TV on or off (standby). 18RETURN button Returns to the previous menu (for SVCD/Video CD). 19DIMMER button Adjusts the brightness or turns off the display. 20VSS button Turn on/off the simulated Virtual Surround Sound system. 21+10/MUTING button Used when selecting or

46、programming numbered tracks or scenes above 10. During disc play press to mute sound. 22TV/VIDEO/CANCEL button Used to switch inputs when controlling the TV. Used to remove selected items when setting up pro- grammed track play. ALso used when setting up the RR-DV96 to control the TV. 23AUDIO/fs/RAT

47、E button Selects various audio options during disc play. fs/ RATE function is not used. 24ZOOM button When viewing video discs allows the image on the screen to be enlarged from 1.8 to 64 times normal size. 25VFP/PROG SCAN button The VFP function is used to set video play prop- erties. Progressive S

48、can function is used to select interlaced or progressive scan output when the Video Signal Selector switch is set to Remote. See the Audio/Video Connections section. 26/NEXT button Skips forward a chapter, title or track. Holding down this button during playback advances play- back rapidly. 27II (PA

49、USE) button Pauses playback. 28? (PLAY)/SELECT button Starts playback.SELECT function is not used. 29/SLOW button During playback lets you advance disc play at 1.5 to 60 times normal speed. When disc play is paused press to advance disc play at 1/2 to 1/32 normal speed. 30MENU button Displays various menus that let you select items from the disc. 31CHANNEL +/CURSOR ? Button When in TV mode press to go to a higher chan- nel. When in DVD mode press to select an item from a menu or on-screen display, or to change the setting of an item in the on-screen disp