Denon-AVR2800-avr-sm维修电路图 手册.pdf

《Denon-AVR2800-avr-sm维修电路图 手册.pdf》由会员分享，可在线阅读，更多相关《Denon-AVR2800-avr-sm维修电路图 手册.pdf（130页珍藏版）》请在收音机爱好者资料库上搜索。

1、2 AVR-2802/982 SPECIFICATIONS ? ? ? ? ? AUDIO SECTION ? ? ? ? ? Power Amplifier Rated output:Front:90W + 90W (8/ohms, 20Hz 20kHz with 0.05% T.H.D.) 135W + 135W (6/ohms, 1kHz with 0.7% T.H.D.) 150W + 150W (6/ohms, EIAJ) Center:90W (8/ohms, 20Hz 20kHz with 0.05% T.H.D.) 135W (6/ohms, 1kHz with 0.7% T.

2、H.D.) 150W (6/ohms, EIAJ) Surround:90W + 90W (8/ohms, 20Hz 20kHz with 0.05% T.H.D.) 135W + 135W (6/ohms, 1kHz with 0.7% T.H.D.) 150W + 150W (6/ohms, EIAJ) Surround Back: 90W (8/ohms, 20 Hz 20kHz with 0.05% T.H.D.) 135W (6/ohms, 1kHz with 0.7% T.H.D.) 150W (6/ohms, EIAJ) Dynamic power:120W 2ch (8/ohm

3、s) 170W 2ch (4/ohms) 200W 2ch (2/ohms) Output terminals:Front:A or B 6 16/ohms A + B 8 16/ohms Center, Surround, Surr.Back: 6 16/ohms ? ? ? ? ? Analog Input sensitivity/input impedance:200mV/47k/kohms Frequency response:10Hz 100kHz: +0, 3dB (DIRECT mode) S/N:102dB (DIRECT mode) Distortion:0.005% (20

4、Hz 20kHz) (DIRECT mode) Rated output:1.2V ? ? ? ? ? Digital D/A output:Rated output 2V (at 0dB playback) Total harmonic distortion 0.008% (1 kHz, at 0 dB) S/N ratio 102dB Dynamic range 96dB Digital input:Format Digital audio interface ? ? ? ? ? Phono equalizer (PHONO input REC OUT) Input sensitivity

5、:2.5mV RIAA deviation:1dB (20Hz to 20kHz) Signal-to-noise ratio:74dB (A weighting, with 5mV input) Rated output/Maximum output:150mV/7V Distortion factor:0.03% (1kHz, 3V) ? ? ? ? ? VIDEO SECTION ? ? ? ? ? Standard video jacks Input/output level and impedance:1Vp-p, 75/ohms Frequency response:5Hz 10M

6、Hz +0, 3dB ? ? ? ? ? S-video jacks Input/output level and impedance:Y (brightness) signal 1Vp-p, 75/ohms C (color) signal 0.286Vp-p, 75/ohms Frequency response:5Hz 10MHz +0, 3dB ? ? ? ? ? Color component video jacks Input/output level and impedance:Y (brightness) signal 1Vp-p, 75/ohms PB/CB (blue) s

7、ignal 0.7Vp-p, 75/ohms PR/CR (red) signal 0.7Vp-p, 75/ohms Frequency response:5Hz 27MHz +0, 3dB ? ? ? ? ? TUNER SECTION FM (note: V at 75/ohms, 0dBf=1 10-15 W)AM Receiving Range:87.50MHz 107.90MHz520kHz 1710kHz (for U.S.A., Canada and multiple voltage models)(for U.S.A., Canada and Multiple voltage

8、models) 87.50MHz 108.00MHz522kHz 1611kHz (for Europe, Asia, China, Hong Kong, Taiwan R.O.C. and Multiple voltage models)(for Europe, Asia, China, Hong Kong, Taiwan R.O.C. and multiple voltage models) Usable Sensitivity:1.0V (11.2dBf)18V 50dB Quieting Sensitivity:MONO: 1.6V (15.3dBf) STEREO: 23V (38.

9、5dBf) S/N (IHF-A):MONO: 77dB STEREO: 72dB Total Harmonic Distortion (at 1kHz):MONO: 0.15% STEREO: 0.3% ? ? ? ? ? GENERAL Power supply:AC120V, 60Hz (for U.S.A., Canada and Taiwan R.O.C. models) AC230V, 50Hz (for Europe model) AC220V, 50Hz (for China model) AC115V/230V, 50/60Hz (for Asia, Hong Kong an

10、d Multiple voltage models) Power consumption:5.0A (for U.S.A. Edge detection is “Ed”; Detection by both shifting is “E Serial data detection is “S” (Serial data output is also “S”). Res:State at reset. “H”= Outputs High Level at reset “L”= Outputs Low Level at reset “Z”= Becomes High impedance mode

11、at reset Ini:Initial output state. Function:Function and logical level explanation of signals to be interface. RadioFans.CN TMP93CS40F (AU: IC301) NameFunction TMP93CS40F Terminal Function Pin No. 1V REFLA/D ref. GND 2A VssA/D GND 3A VccAD +5V 4_NMIINot used (fixed to H) 5P70/TI0C15OCEdLLFixed to L

12、(DSP ROM address cont. out bit 15, not used) 6P71/TO1C16OCEdLLDSP program ROM address cont. out bit 16 7P72/TO2C17OCEdLLDSP program ROM address cont. out bit 17 8P73/TO3ROM/RAMOCEdLLROM/RAM switching control terminal (L:ROM) 9P80/INT4/TI4_INTREQ OUTI/OCEuE&LZDSP request input and cont. output (L:Rq

13、& cont.) 10P81/INT5/TI5B.DOWNIEuE&LZPower down detect (H: Detected) 11P82/TO4OCLL 12P83/TO5_REQOCEuHL MAIN-SUB CPU comm. control output (L: Comm. request from sub) 13P84/INT6/TI6_ACKIEuE&LMAIN-SUB CPU comm. control input (L: Ack. return from main) 14P85/INT7/TI7ERRIE&LDIR control input terminal (LC8

14、9055Q)( H: ERR) 15P86/TO6ILvZ(GND) 16P97/INT0_CSIEdE&L DIR control input terminal (LC89055Q), when CH status change LH 17P90/TXD0SIOCMAIN-SUB CPU comm. control terminal (data output) 18P91/RXD0SOIMAIN-SUB CPU comm. control terminal (data input) 19P92/_CTS0/SCLK0CLKI/OCMAIN-SUB CPU comm. control term

15、inal (I2C clock in/output) 20P93/TXD1OCZL 21P94/RXD1OCZL 22P95/SCLK1OCZL 23AM8/_16Fixed to +5V 24CLKOCEu 25Vcc+5V 26VssI/O1GND 27X1XinIXtal connection 28X2XoutOXtal connection 29_EAFixed to +5V 30_RESETRESET2_IEuLvLReset input (controlled by main CPU) 31P96/XT1A/D RESETONEuHHA/D control terminal (L:

16、 Reset) 32P97/XT2OCEdLL 33TEST1IConnected to TEST2 34TEST2IConnected to TEST1 35PA0DINAOCEdLLDigital input switching control output 36PA1DINBOCEdLLDigital input switching control output 37PA2OCLL 38PA3DINCOCEdLLDigital input switching control output 39PA4DOUTAOCEdLLDigital output switching control o

17、utput 40PA5DOUTBOCEdLLDigital output switching control output SymbolI/OTypeOpDetResInit NameFunction Pin No. 41PA6DEEMPOCEdLLDAC de-emphasis filter cont. out terminal (H:ON) 42PA7/SCOUT96k-DACOCLLDAC control terminal (H: Sample frequency 96kHz) 43ALEOCLL(Address latch enable) 44Vcc+5V 45P00/AD0(AD0)

18、I/OCZL(EPROM data in D0 / address out A0) 46P01/AD1(AD1)I/OCZL(EPROM data in D1 / address out A1) 47P02/AD2(AD2)I/OCZL(EPROM data in D2 / address out A2) 48P03/AD3(AD3)I/OCZL(EPROM data in D3 / address out A3) 49P04/AD4(AD4)I/OCZL(EPROM data in D4 / address out A4) 50P05/AD5(AD5)I/OCZL(EPROM data in

19、 D5 / address out A5) 51P06/AD6(AD6)I/OCZL(EPROM data in D6 / address out A6) 52P07/AD7(AD7)I/OCZL(EPROM data in D7 / address out A7) 53P10/AD8/A8(A8)OCZL(EPROM address out A8) 54P11/AD9/A9(A9)OCZL(EPROM address out A9) 55P12/AD10/A10(A10)OCZL(EPROM address out A10) 56P13/AD11/A11(A11)OCZL(EPROM add

20、ress out A11) 57P14/AD12/A12(A12)OCZL(EPROM address out A12) 58P15/AD13/A13(A13)OCZL(EPROM address out A13) 59P16/AD14/A14(A14)OCZL(EPROM address out A14) 60P17/AD15/A15(A15)OCZL(EPROM address out A15) 61_WDTOUTOCZHWatch dog output 62VssGND 63Vcc+5V 64P20/A0/A16(A16)OCZL(EPROM address out A16) 65P21

21、/A1/A17DIR CLKOCZLDIR control terminal (LC89055Q) control clock output 66P22/A2/A18DIR CEOCZLDIR control terminal (LC89055Q) control chip enable output 67P23/A3/A19DIR MOSIOCZLDIR control terminal (LC89055Q) control data output 68P24/A4/A20DIR MOSOILvDIR control terminal (LC89055Q) control data inpu

22、t 69P25/A5/A21FGAINOCEdLLFRONT ch GAIN switching control output (H: SW=NO) 70P26/A6/A22DAC-RESETOCEdLHDAC control terminal (L: Power down mode, (rising edge) Reset) 71P27/A7/A23SEL CKOCZLADC/DIR data clock switching control terminal (L: ADC) 72P30/_RD(_RD)OCZL(Flash memory control terminal) 73P31/_W

23、R(_WR)OCZL(Flash memory control terminal) 74P32/_HWRCSIILvDIR control input terminal (L: PCM) 75P33/_WAITERR MUTE_OCEdLLPop noise preventive mute control output (L: Mute) 76P34/_BUSRQILvZGND 77P35/_BUSRQDIG.(AC3) MUTEOCEdZLDigital mute control output (L: AC-3 or DTS decode enable) 78P36/_R/WILvZGND

24、79P37/_RASDIR RESETOCZLDIR control output (LC89055Q) (L: Reset) 80P40/_CS0/_CAS0OCZL 81P41/_CS1/_CAS1OCZL 82P42/_CS2/_CAS2(_CS0)OCZL(Flash memory control terminal) 83P60/PG00DSP. RESETOCZLDSP reset output terminal (L:Reset) 84P61/PG01I/02 SCD OUTICLvZDSP status data input terminal 85P62/PG02I/03 DSP

25、. CSOZLDSP chip select cont.output (L:Data out) 86P63/PG03I/04 DSP. CLKOCZLDSP data clock output terminal 87P64/PG10I/05 SCD INOCZLDSP data output terminal 88P65/PG11I/06 4527_CEOCZLAD control terminal (AK4527), Chip enable output 89P66/PG12I/07 4527_CLKOCZLAD control terminal (AK4527), Data clock o

26、utput 90P67/PG13I/08 4527_DINOCZLAD control terminal (AK4527), Data output 91VssGND 92P50/AN0INTTREQ INIEuLvZ 93P51/AN1IEuLvZ 94P52/AN2EMPILvH: EMP on 95P53/AN396K DETILv96k signal detect input, H: 96k 96P54/AN4IEuLvZ 97P55/AN5IEuLvZ 98P56/AN6ACC ON/OFFIEuLvZ 99P57/AN7IEuLvZ 100V REFHAD ref. +5V Sym

27、bolI/OTypeOpDetResInit? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 16 AVR-2802/982 RadioFans.CN AVR-2802/982 17 1,12,23VD1,2,3Digital power supply (+) 2,13,24DGND1,2,3Digital GND 3AUDATA3, XMT958SPDIF transmitter output, Digital audio output 3 4WR, DS, EMWR, GPIO10 Host write strobe, Host data strobe, External m

28、emory write enable, General purpose in/output 10 5RD, R/W, EMOE,GPIO11 Host parallel output enable, Host parallel R/W, External memory write enable, General purpose in/output 11 6A1,SCDINHost address bit 1, SPI serial control data input 7A0,SCCLKHost address bit 0, Serial control port clock 8DATA7,

29、EMAD7, GPIO7Bidirectional data bus 7, External memory address 7, General purpose in/output 7 9DATA6, EMAD6, GPIO6Bidirectional data bus 6, External memory address 6, General purpose in/output 6 10DATA5, EMAD5, GPIO5Bidirectional data bus 5, External memory address 5, General purpose in/output 5 11DA

30、TA4, EMAD4, GPIO4Bidirectional data bus 4, External memory address 4, General purpose in/output 4 14DATA3, EMAD3, GPIO3Bidirectional data bus 3, External memory address 3, General purpose in/output 3 15DATA2, EMAD2, GPIO2Bidirectional data bus 2, External memory address 2, General purpose in/output

31、2 16DATA1, EMAD1, GPIO1Bidirectional data bus 1, External memory address 1, General purpose in/output 1 17DATA0, EMAD0, GPIO0Bidirectional data bus 0, External memory address 0, General purpose in/output 0 18CSHost parallel chip select, Host serial SPI chip select 19SCDIO, SCDOUT, PSEL,GPIO9Serial c

32、ontrol port data in/output, Parallel port type select, General purpose in/output 9 20INTREQ, ABOOTControl port interrupt request, Automatic boot enable 21EXTMEM, GPIO8External memory chip select, General purpose in/output 8 22SDATAN1PCM audio data input 1 25SCLKN1, STCCLK2PCM audio input bit clock 2

33、6LRCLKN1PCM audio input sample rate clock 27CMPDAT, SDATAN2PCM audio data input 2 28CMPCLK, SCLKN2PCM audio input bit clock 29CMPREQ, LRCLKN2PCM audio input sample rate clock 30CLKINMaster clock input 31CLKSELDSP clock select 32FILT2PLL filter 33FILT1PLL filter 34VAAnalog power supply (+) 35AGNDAnal

34、og GND 36RESETMaster reset input 37DDReserved 38DCReserved 39AUDATA2Digital audio output 2 40AUDATA1Digital audio output 1 41AUDATA0Digital audio output 0 42LRCLKAudio output sample rate clock 43SCLKAudio output bit clock 44MCLKAudio master clock A0, SCCLK7 DATA7, EMAD7, GPIO78 DATA6, EMAD6, GPIO69

35、DATA5, EMAD5, GPIO510 DATA4, EMAD4, GPIO411 VD212 DGND213 DATA3, EMAD3, GPIO314 DATA2, EMAD2, GPIO215 DATA1, EMAD1, GPIO116 DATA0, EMAD0, GPIO0 AUDATA2 DC DD RESET AGND VA FILT1 FILT2 CLKSEL CLKIN CMPREQ, LRCLKN217 CS18 SCDIO, SCDOUT,PSEL, GPIO919 ABOOT, INTREQ20 EXTMEM, GPIO821 SDATAN122 VD323 DGND

36、324 SCLKN1, STCCLK225 LRCLKN126 CMPDAT,SDATAN2, RCV95827 CMPCLK, SCLKN228 39 38 37 36 35 34 33 32 31 30 29 A1, SCDIN RD, R/W, EMOE, GPIO11 WR/DS/EMWR, GPIO10 AUDATA3, XMT958 DGND1 VD1 MCLK SCLK LRCLK AUDATA0 AUDATA1 6 5 4 3 2 1 44 43 42 41 40 Top View CS493292-CL (AU: IC814) ? CS493292-CL Terminal F

37、untion Port NameFunctionPin No. RadioFans.CN 18 AVR-2802/982 LC89055W (AU: IC800) Pin NameFunction LC89055W Terminal Function Pin No. 1DISELIData input terminal (select input pin of DIN0, DIN1) 2DOUTOInput bi-phase data through output terminal 3DIN0IAmp built-in coaxial/optical input correspond data

38、 input terminal 4DIN1IAmp built-in coaxial/optical input correspond data input terminal 5DIN2IOptical input correspond data input terminal 6DGNDDigital GND 7DVDDDigital power supply 8RIVCO gain control input terminal 9VINIVCO free-run frequency setting input terminal 10LPFOPLL loop filter setting te

39、rminal 11AVDDAnalog power supply 12AGNDAnalog GND 13CKOUTOClock output terminal (256fs, 384fs, 512fs, Xtal osc., VCO free-run osc.) 14BCKO64fs clock output terminal 15LRCKOfs clock output terminal (L: Rch, H: Lch, I2S: Reverse) 16DATAOOData output terminal 17XSTATEOInput data detecting result output

40、 terminal 18DGNDDigital GND 19DVDDDigital power supply 20XMCKOXtal osc. clock output terminal (24.576MHz or 12.288MHz) 21XOUTOXtal osc. connection output terminal 22XINIXtal osc. connection input terminal, external signal input possible (24.576MHz or 12.288MHz) 23EMPHAOEmphasis information output te

41、rminal of channel status 24AUDIOOBit1 output terminal of channel status 25CSFLAGOTop 40bit revise flag output terminal of channel status 26F0/P0/C0OInput fs cal. sig. out / data type out / input word inf. output terminal 27F1/P1/C1OInput fs cal. sig. out / data type out / input word inf. output term

42、inal 28F2/P2/C2OInput fs cal. sig. out / data type out / input word inf. output terminal 29VF/P3/C3OValidity flag out / data type out / input word inf. output terminal 30DVDDDigital power supply 31DGNDDigital GND 32AUTOONon PCM burst data transfer detect sig. output terminal 33BPSYNCONon PCM burst d

43、ata preamble Pa, Pb, Pc, Pd sync sig. output terminal 34ERROROPLL lock error, data error flag output terminal 35DOOCPU I/F read data output terminal 36DIICPU I/F write data input terminal 37CEICPU I/F chip enable input terminal 38CLICPU I/F clock input terminal 39XSELIFrequency select input pin of X

44、IN Xtal osc. (24.576MHz or 12.288MHz) 40MODE0IMode setting input terminal 41MODE1IMode setting input terminal 42DGNDDigital GND 43DVDDDigital power supply 44DOSEL0IData output format select input terminal 45DOSEL1IData output format select input terminal 46CKSEL0IOutput clock select input terminal 4

45、7CKSEL1IOutput clock select input terminal 48XMODEIReset input terminal I/O * For latch-up countermeasure, set digital (DVDD) and analog (AVDD) power on/off in the same timing. ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?

46、 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?

47、 ? ? ? ? RadioFans.CN 19 AVR-2802/982 M35015-210SP Terminal Function Pin No.SymbolNameI/OFunction 1OSC1Osc. circuit ext.IExternal terminal for indication oscillator circuit. Standard OSC. freq. is approx. 7MHz. 2OSC2terminal.OWith this OSC. freq., decides horizontal indicatin and character width. 3C

48、SChip select inputI Chip select terminal and turns to “L” when transfer serial data. Hysteresis input. Pull up resistor is built-in. 4SCKSerial clock inputI Takes in serial data of SIN at SCK rise when CS terminal is in “L”. Hysteresis input. Pull up rersist is built-in. 5SINSerial data inputI Seria

49、l input of register for indication control and data, and address for indication data memory. Hysteresis input. Pull up rersistor is built-in. 6ACAuto-clear inputI Resets internal circuit of IC at “L” mode. Hysteresi input. Pull up resistor is built-in. 7VDD2Power supply?Power supply terminal of analog system. Connect to +5V. 8CVIDEO Combined video output O Output terminal of combined video signal. Outputs 2Vp-p combined signal. Character output, etc. Overlap CVIN signal and outputs at superimpose. 9LECHA Character level input I Input terminal d