HarmanKardon-DVD29.230-cd-sm维修电路原理图.pdf

《HarmanKardon-DVD29.230-cd-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-DVD29.230-cd-sm维修电路原理图.pdf（55页珍藏版）》请在收音机爱好者资料库上搜索。

1、 harman/kardon Service Manual DVD 29/230 DVD player CONTENTS TECHNICAL SPECIFICATIONS 2 TROUBLESHOOTING GUIDE 3 FRONT PANEL CONTROLS 4 FRONT PANEL DISPLAY 5 REAR PANEL CONNECTIONS 6 SETUP AND CONNECTIONS 7 EXPLODED VIEW 9 PARTS LIST 10 SEMICONDUCTOR PINOUTS 24 WIRING DIAGRAM 50 SCHEMATIC DIAGRAMS 51

2、 Released EU2008 harman/kardon, Inc. Rev 0, 10/2008 250 Crossways Park Dr. Woodbury, New York, 11797 RadioFans.CN ENGLISH Technical Specifications Applicable Disc:Disc formats: 5 inch (12 cm) or 3 inch (8 cm) DVD Video, DVD-Audio, Standard conforming DVD+RW, DVD+R, DVD-R, DVD-RW, DivX,VCD, CD, CD-R,

3、 MP3,WMA, JPEG or CD-RW discs, Regio code: DVD Movie disc with Code 2 or 0 only. DVD-Layers: Single Side/Single Layer, Single Side/Dual Layer, Dual Side/Single Layer, Dual Side/Dual Layer Audio formats: DVD-Audio MLP lossless, Linear PCM, MPEG,Windows Media9, Dolby Digital or DTS Audio discs Still-i

4、mage format: JPEG Video Signal System:PAL/NTSC HDMIOutput:Video: 576p, 720p, 1080i HDMI Version 1.0-compliant HDCP Version 1.1-compliant Composite Video Output:1 Vp-p/75 Ohms, sync negative polarity S Video Output:Y/Luminance: 1 Vp-p/75 Ohms, sync negative polarity C/Chrominance: 0.286 Vp-p Componen

5、t Video Output:Y: 1 Vp-p/75 Ohms, sync negative polarity Cr: 0.7 Vp-p/75 Ohms Cb: 0.7 Vp-p/75 Ohms Analog Audio Output:2 Vrms max Frequency Response:DVD (Linear PCM):2Hz - 22kHz (48kHz sampling) 2Hz - 44kHz (96kHz sampling) CD:2Hz - 20kHz Signal/Noise Ratio (SNR):105 dB (A-weighted) Dynamic Range:DV

6、D: 100dB (18 Bit) / 105dB (20 Bit) CD/DVD: 96dB (16 Bit) THD/1kHz:DVD/CD: 0.0025 % Wow align the disc with the guides and place it in its proper position. Incorrect disc type Check to see that disc is CD, CD-R, CD-RW, DivX,VCD, MP3,WMA, JPEG, DVD-R, DVD-RW, DVD+R, DVD+RW (standard conforming), DVD-A

7、udio or DVD-Video; other types will not play. Invalid Region Code Use Region 2 or Open Region (0) disc only. Rating is above parental preset Enter password to override or change rating settings. No picture Intermittent connections Check all video connections. Wrong input Check input selection of TV

8、or receiver. Progressive Scan output selected Use Progressive Scan mode only with compatible TV. If needed, press the Progressive Scan/Interlaced ButtonLto toggle to the correct mode. Video Off feature active Press Video Off ButtonQto reactivate video circuitry (see page 23) HDMI Output?is connected

9、 to a The HDMI Output?may not be used with video displays that are not video display that is not HDCP-compliantHDCP-compliant. Unplug the cable and select another audio and video connection (see pages 11 through 12). No sound Intermittent connections Check all audio connections. Incorrect digital au

10、dio selection Check digital audio settings. DVD disc is in fast or slow mode There is no audio playback on DVD discs during fast or slow modes. Surround receiver not compatible Use analog audio outputs. with 96kHz PCM audio DVD Audio disc is loaded without Use 6-Channel Audio Outputs?or Analog Audio

11、 Outputs?. using analog audio connection Picture is distorted or jumps during MPEG-2 decoding It is a normal artifact of DVD playback for pictures to jump or show fast forward or reverse playsome distortion during rapid play. Some remote buttons do not operate Function not permitted at this time Wit

12、h most discs, some functions are not permitted at certain during DVD play; prohibited symbol times (e.g.,Track Skip) or at all (e.g., direct audio track selection). appears (see below) The OSD menu is in a foreign language Incorrect OSD language Change the display language selection. The symbol appe

13、ars Requested function not available at Certain functions may be disabled by the DVD itself during this timepassages of a disc. Picture is displayed in the Incorrect match of aspect ratio settings Change aspect ratio settings. wrong aspect ratioto disc Remote control inoperative Weak batteries Chang

14、e both batteries. Sensor is blocked Clear path to sensor or use optional outboard remote sensor. Disc will not copy to VCR Copy protection Many DVDs are encoded with copy protection to prevent copying to VCR. Password not accepted Incorrect password being used or Stop play of disc. Press and hold th

15、e Clear Button?until the display password has been forgottenblinks.This resets the password and all settings to their defaults. 33908_DVD29_ENG 18/07/07 16:43 Side 26 RadioFans.CN Front Panel Controls ?Main Information Display:This display delivers messages and status indications to help you operate

16、 the DVD player. 1Power On/Off (Standby): Press the button once to turn the DVD player on, press it again to put the unit in the Standby mode. 2Open/Close: Press this button to open or close the Disc Tray. 3Play/Pause: Press to initiate playback or to resume playback after Pause has been pressed. Pr

17、ess this button to momentarily pause play- back.To resume playback, press the button again. If a DVD is playing, action will freeze and a still picture will be displayed when the button is pressed. 4SETUP: Press this button to use the DVD 29s on-screen menu system to adjust the players configuration

18、 settings. Note that the Info ButtonAmust be pressed to access the DVD 29s Player Information menu to obtain detailed disc information, and to configure the playback mode of the disc. 5Stop: Press this button once to place the disc in the Resume mode, which means that playback will stop, but as long

19、 as the tray is not opened or the disc changed, DVD playback will continue from the same point on the disc when the Play Button is pressed again. Resume will also work if the unit was turned off.To stop a disc and have play start from the beginning, press the button twice. 6Skip/Search (Previous): P

20、ress this button to move backward through the music tracks on a CD disc or the chapters on a DVD disc. Keep the button pressed to search backwards at one of the available speeds. 7Skip/Search (Next): Press to move forward through the music tracks on a CD or the chapters on a DVD disc. Keep the butto

21、n pressed to search forwards at one of the available speeds. 8Dimmer: Press this button to reduce the brightness of the Information Display by 50% or to turn the display off completely in the following order: FULL BRIGHTNESS HALF BRIGHTNESS OFF FULL BRIGHTNESS. 9ARROW buttons (M/N): Use to move the

22、cursor in the OSD. AENTER: Press this button to activate a setting or option. BARROW buttons (K/L): Use to move the cursor in the OSD. ?Main Information Display 1Power On/Off (Standby) 2Open/Close 3Play/Pause 4Setup 5Stop 6Skip/Search (Previous) 7Skip/Search (Next) 8Dimmer 9Arrows left and right AEn

23、ter BArrows up and down 139AB45678 2? 33908_DVD29_ENG 18/07/07 16:43 Side 6 harman/kardonDVD 29/230 Service Manual Page 4 of 55 ENGLISH Front Panel Information Display A L B C DEF GHIJ KMNO A Disc Type Indicators B Playback-Mode Indicators CAudio Bitstream Indicators D Chapter/Track Number Indicator

24、s ETime Indicators FTitle Indicators GV-OFF Indicator H Repeat Indicators IVCD Playback Control Indicator J Random Indicator KA-B Repeat Indicator L Program Indicator MAngle Indicator N Parental Lock Indicator OVideo Output Indicators A Disc Type Indicators: The CD, DVD, DVD- Audio,VCD, MP3,WMA or J

25、PEG indicator will illuminate to show the type of disc currently being played. B Playback-Mode Indicators:These indicators light to show the current playback mode: BLights when a disc is playing in the normal mode HLights when the disc is in the Fast Search Forward mode.The on-screen banner display

26、indicates the selected speed (x2, x4, x8, x20, x100). 1 Lights when the disc is paused. GLights when the disc is in the Fast Search Reverse mode.The on-screen banner display indicates the selected speed (x2, x4, x8, x20, x100). C Audio Bitstream Indicators:When a DolbyDigital, DTSor linear PCM digit

27、al audio signal is present on the disc, one of these indicators will light. DVD-Audio, MP3 and WMA bitstreams will be indicated by the Disc Type Indicator A. D Chapter/Track Number Indicators:When a DVD disc is playing, these two positions in the display will show the current chapter.When a CD disc

28、is playing they will show the current track number. E Time Indicators:These positions in the indicator will show the running time of a DVD in play.When a CD is playing, these indicators will show the current track time, time remaining in the current track, or the total remaining time on the disc. NO

29、TE: The Indicators DEF will also display text messages about the DVDs status, including LOADINGwhen a disc is loading, POWER OFFwhen the unit is turned off, and DISC ERRORwhen a disc not compatible with the DVD is put into the play position. F Title Indicators: These two positions in the display wil

30、l show the current title number when a DVD disc is playing. G V-OFF Indicator: This indicator lights when the units video output has been turned off by pressing the V-OFF button on the remote control. H Repeat Indicators:These indicators light when any of the Repeat functions are in use. I VCD Playb

31、ack Control Indicator:This indicator lights when the playback control function is turned on with VCDs. J Random Indicator: This indicator lights when the unit is in the Random Play mode. K A-B Repeat Indicator:This indicator lights when a specific passage for repeat playback has been selected. L Pro

32、gram Indicator:This indicator lights when the programming functions are in use. M Angle Indicator: This indicator blinks when alternative viewing angles are available on the DVD currently playing. N Parental Lock Indicator:This indicator lights when the parental-lock system is engaged in order to pr

33、event anyone from changing the rating level without a code. O Video Output Indicators:When the DVD 29 is connected to a video display using the HDMI Output?, the display sends infor- mation to the DVD 29 indicating the highest video resolution it is capable of handling, and the DVD 29 automatically

34、sets the video output to match it.That resolution is displayed here. You may use the HD Mode Selector?to manually select a lower video output resolution. 33908_DVD29_ENG 18/07/07 16:43 Side 7 harman/kardonDVD 29/230 Service Manual Page 5 of 55 Rear Panel Connections ? ? ? ? ? ? ? ? ? ? ?Optical Digi

35、tal Output ?Coaxial Digital Output ?AC Power Cord ?Composite Video Output ?S-Video Output ?Component Video Outputs ?Scart TV Output ?Remote Control Output ?Remote Control Input ?Analog Audio Output ?HDMI Output ?6-Channel Audio Outputs ?Optical Digital Output: Connect this jack to the optical digita

36、l input of an A/V receiver or surround processor for Dolby Digital, DTS or PCM audio playback. ?Coaxial Digital Output: Connect this jack to the coaxial digital input of an A/V receiver or surround processor for Dolby Digital, DTS or PCM audio playback. NOTE:The coaxial digital output should only be

37、 connected to a digital input. Even though it is the same RCA-type connector as standard analog audio connections, DO NOT connect it to a conventional analog input jack. Connect either the Optical Digital Audio Output?or the Coaxial Digital Audio Output?to a corresponding digital audio input on your

38、 receiver or processor, but not both. ?AC Power Cord: Connect this plug to an AC outlet. If the outlet is controlled by a switch, make certain that it is in the ON position. ?Composite Video Output: Connect this jack to the video input on a television or video projector, or to a video input on an A/

39、V receiver or processor if you are using that type of device for video input switching. ?S-Video Output: Connect this jack to the S-Video input on a television or video projector, or to an S-Video input on an A/V receiver or processor if you are using that type of device for S-Video input switching.

40、 ?Component Video Outputs: These out- puts carry the component video signals for connection to display monitors with component video inputs. For standard analog TVs or projectors with inputs marked Y/Pr/Pb or Y/Cr/Cb, connect these outputs to the correspon- ding inputs. If you have a high-definition

41、 televi- sion or projector that is compatible with high scan rate progressive video, connect these jacks to the “HD Component” inputs. Note that if you are using a progressive scan display device, then ”Progressive” must be selected in the Video Set- up Menu in order to take advantage of the progres

42、sive scan circuitry. See page 19 for more information on progressive scan video. IMPORTANT:These jacks should NOT be connected to standard composite video inputs. ?SCART OUT (TV): If your TV has a SCART socket, you can connect a SCART cable to your TV and to your DVD Player for improved video qualit

43、y.The SCART cable carries both audio and video.You can select Composite Video or RGB video for that SCART connectors video output signal. ?Remote Control Output: Connect this jack to the infrared (IR) input jack of another compatible Harman Kardon remote controlled product to have the built-in Remot

44、e Sensor on the DVD provide IR signals to other compatible products. ?Remote Control Input: Connect the output of a remote infrared sensor, or the remote control output of another compatible Harman Kardon product, to this jack.This will enable the remote control to operate even when the front panel

45、Remote Sensor on the DVD is blocked.This jack may also be used with compatible IR remote control-based automation systems. ?Analog Audio Output: Connect these jacks to an audio input on an A/V receiver or surround processor for analog audio playback. ?HDMI Output: If you have an HDMI-com- patible re

46、ceiver or video display device, connect this output to an HDMI input on the receiver or video display for the highest-quality uncom- pressed digital audio and video available. Even if your receiver is not capable of processing audio in the HDMI format, you may still experience the superb reproductio

47、n of HDMI video. If your video display has a DVI input, you may use an optional HDMI-to-DVI cable or adapter for the connection to the display. In all cases, the video display must be HDCP-compliant in order to use the HDMI output. For best results, we do not recommend HDMI connections in excess of

48、ten feet. The following audio formats may be output via the HDMI connection: Audio CD 2-Channel PCM or 5.1-channel DTS DVD-Audio 2-Channel PCM DVD-Video Up to 5.1-channel Dolby Digital or DTS Note:To hear the high-resolution surround sound recorded on DVD-Audio discs, you need to connect the 6-Chann

49、el Audio Outputs? to the corresponding input jacks on your receiver or processor.These formats are not output digi- tally. ?6-Channel Audio Outputs: Connect these outputs to the matching 6-channel analog audio inputs on your receiver or surround sound processor.This connection is required to listen to the multichannel tracks on DVD-Audio discs. If the disc also contains a linear PCM, Dolby Digital or DTS track, yo