《Panasonic-SAXR55P-avr-sm维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《Panasonic-SAXR55P-avr-sm维修电路原理图.pdf(129页珍藏版)》请在收音机爱好者资料库上搜索。
1、n AMPLIFIER SECTION Rated minimum sine wave RMS power output 20 Hz-20 kHz both channels driven 0.09 % total harmonic distortion100 W per channel (6 ) 1 kHz continuous power output both channels driven 0.09 % total harmonic distortion105 W per channel (6 ) Total harmonic distortion rated power at 20
2、Hz-20 kHz0.09 % (6 ) Power bandwidth both channels driven, -3 dB4 Hz-88 kHz (6 , 0.9 %) Power output each channel driven 0.9 % total harmonic distortion at 1kHz Front (L/R)100 W (6 ) Center100 W (6 ) Surround (L/R)100 W (6 ) Surround Back (L/R)100 W (6 ) Load impedance Front (L/R) A or B6-8 A and B6
3、-8 BI-WIRE6-8 Center6-8 Surround (L/R)6-8 Surround Back (L/R)6-8 Frequency response CD, TAPE, TV, DVD, DVD RECORDER, VCR1, VCR2 4 Hz-88 kHz, 3 dB DVD 6CH4 Hz-44 kHz, 3 dB 2005 Matsushita Electric Industrial Co. Ltd. All rightsreserved.Unauthorizedcopyingand distribution is a violation of law. SA-XR5
4、5P SA-XR55PC Colour (S).Silver Type (K).Black Type (P only) Input sensitivity CD, TAPE, TV, DVD, DVD RECORDER, VCR1, VCR2 27 mV (200mV, IHF 66) Input impedance CD, TAPE, TV, DVD, DVD RECORDER, VCR1, VCR2 22 k S/N (IHF A) CD, TV, DVD, DVD RECORDER (Digital Input) 85 dB (103 dB, IHF 66) Tone controls
5、BASS50 Hz, +10 to -10 dB TREBLE20 kHz, +10 to -10 dB Subwoofer frequency response (-6 dB)7 Hz-200 Hz n FM TUNER SECTION Frequency range87.9-107.9 MHz Sensitivity11.2 dBf (2 V, IHF 58) 50 dB quieting sensitivity MONO18.3 dBf (4.5 V, IHF 58) STEREO38.3 dBf (45 V, IHF 58) Total harmonic distortion MONO
6、0.2% STEREO0.3% S/N AV Control Receiver Specification ORDER NO. MD0504178C1 A1 RadioFans.CN 收音机爱 好者资料库 MONO73 dB STEREO67 dB Frequency response20 Hz-15 kHz, +1 dB, -2 dB Alternate channel selectivity65 dB Capture ratio1.5 dB Image rejection at 98 MHz40 dB Spurious response rejection at 98 MHz75 dB A
7、M suppression50 dB Stereo separation 1 kHz40 dB 10 kHz30 dB Antenna terminal75 (unbalanced) n AM TUNER SECTION Frequency range530-1710 kHz Sensitivity20 V, 330 V/m Selectivity55 dB IF rejection at 1000 kHz50 dB n VIDEO SECTION Output voltage at 1 V input (unbalanced)10.1 Vp-p Maximum input voltage1.
8、5 Vp-p Input/output impedance75 S-Video 1 SAFETY PRECAUTIONS 4 1.1. GENERAL GUIDELINES 4 2 Before Repair and Adjustment 5 3 Protection Circuitry 5 4 Handling the Lead-free Solder 5 4.1. About lead free solder (PbF) 5 5 Accessories 6 6 Operating Instructions 7 6.1. Main Unit 7 6.2. Remote Control 8 6
9、.3. Home Theater Connections 9 6.4. Other Connections 14 7 Disassembly and Main Component Replacement Procedures and Operational Check 17 7.1. Disassembly flow chart 17 7.2. P.C.B. Positions 18 7.3. Disassembly of Top Cabinet. 18 7.4. Checking for the DSP P.C.B. (Side A/B) and Main P.C.B. (Side A).
10、19 InputTV, DVD, DVD RECORDER OutputTV MONITOR Component Video InputTV, DVD, DVD RECORDER OutputTV MONITOR n GENERAL Power supplyAC 120 V, 60 Hz Power consumption135 W Dimensions (W H D)430 mm 107.5 mm 394 mm (16-15/16” 4-7/32” 15-1/2”) Mass4.6 kg (10.1 lb.) n DIN POWER 1 kHz, T.H. D 1%2 x 100 W (6
11、) Notes: 1.Specifications are subject to change without notice. Mass and dimensions are approximate. 2.Total harmonic distortion is measured by the digital spectrum analyzer. 7.5. Disassembly and Checking of Main P.C.B. (Side B) 20 7.6. Disassembly of Tuner Pack and Tuner Extent P.C.B. 20 7.7. Disas
12、sembly and Checking of Speaker P.C.B. 21 7.8. Disassembly and Checking of Component Video P.C.B. 21 7.9. Disassembly and Checking of Video Typically the melting point is 50 - 70F (30 - 40C) higher. Please use a high temperature soldering iron. In case of soldering iron with temperature control, plea
13、se set it to 700 20F (370 10C). Pb free solder will tend to splash when heated too high (about 1100F/600C). When soldering or unsoldering, please completely remove all of the solder on the pins or solder area, and be sure to heat the soldering points with the Pb free solder until it melts enough. 5
14、SA-XR55P / SA-XR55PC RadioFans.CN 收音机爱 好者资料库 5 Accessories Note : Refer to Packaging Materials the power cannot be turned on. Failure in the power circuit system of the unit. This may happen when the direct current electricity is supplied to speaker terminals. Check for the above and replace with ne
15、w parts if necessary. 8.3. Returning to Normal Display Press the POWER button on the unit to exit the function. The power is turned off. 8.4. Overload/Shutdown Detection intenal Condition It detects OVERLOAD, POWER MALFUNCTION with THRM_DET, SHORT_DET and DC_DET input port. It detects the following
16、condition depending on the input of the port as below table. (H: DC 5V / L: DC 0V) PROTDetection of malfunctionDisplay and operation SHORT_DETTHRM_DETDC_DET HLHNormal- LLHSpeaker Short, Malfunction of AmplifierOVERLOAD / POWER OFF LHHDetection of THERMAL PROTECTION -LDetection of POWER MALFUNCTION _
17、 _ _ F76 _ _ _ / POWER OFF 8.5. Overload/Thermal Detection Display When overload is detected, automatic POWER OFF will occur. But if any key on the remote control other than the POWER key is pressed before that (including the HELP key), the scroll display will show SWITCH_OFF_POWER. Then, 1 second a
18、fter display of message, OVERLOAD will be shown on the scroll display. 8.6. Activating Self Diagnosis Function (Servicing Mode) This mode can be used during servicing. 27 SA-XR55P / SA-XR55PC RadioFans.CN 收音机爱 好者资料库 1. Plug the AC adapter to the power source. Press and hold down the MULTI CONTROL bu
19、tton and the SPEAKERS A button, and then press the POWER button at the same time. 2. The message, SERVICE appears on the display for three seconds, and then disappears. Refer to Fig. 8.2. Fig. 8.2 3. When the TUNING DOWN button is pressed, the current program filing number (ex. M45_* for MA123_45) a
20、ppears. The * digit indicates the ROM checksum used for ROM collection, and if the unit is not loaded with ROM, NO appears. When the TUNING UP button is pressed, the sub micro computer program filing number (ex. 523_* for MA678_90) appears. The * digit indicates the ROM checksum used for ROM collect
21、ion, and if the unit is not loaded with ROM, NO appears. 8.7. Analog 6.1 CH Output Check Method When the SUBWOOFER button on the remote controller, the function is switched to Input Inspection Mode, which output analog input signals at L channel of VCR analog input to all channels. 8.8. Returning to
22、 Normal Display Press the POWER button on the unit to exit the function. The power is turned off. 8.9. Activating Self Diagnosis Function (Doctor Mode) This mode can be used during servicing. 1. Plug the AC adapter to the power source. Press and hold down the MULTI-SOURCE RE-MASTER button and the SP
23、EAKERS A button, and then press the POWER button at the same time. 2. Initialize all the setting and set the frequency “99.7MHz” to Tuner. The message, “_DOCTOR_” appears on the display for three seconds, and then disappears. Refer to Fig. 8.3. Fig. 8.3 3. Doctor mode function at some remote control
24、 codes as below table. Remote ControlTest Mode Function and settings SelectorSound Modeother settingsVol/Tone CH 1TUNERSTEREOFrequency : FM min-48dB/0dB CH 2TUNERSTEREOFrequency : FM max-48dB/0dB CH 3TUNERSTEREOFM 98.3MHz-18dB/0dB CH 4TUNERSTEREOFrequency : AM min-48dB/0dB CH 5TUNERSTEREOFrequency :
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Panasonic SAXR55P avr sm 维修 电路 原理图
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。
Panasonic-SAXR55P-avr-sm维修电路原理图.pdf



Pioneer-A90-Service-Manual电路原理图.pdf


