Accuphase-A30-pwr-sm维修电路原理图.pdf

《Accuphase-A30-pwr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Accuphase-A30-pwr-sm维修电路原理图.pdf（4页珍藏版）》请在收音机爱好者资料库上搜索。

1、m Pure Class A operation delivers quality power: 30 watts 2 into 8 ohms m Power MOS-FET output stage features triple parallel push-pull configuration m Instrumentation amplifier principle m Further improved MCS+ circuit topology m Current feedback combines operation stability with outstanding sound

2、m Bridged mode allows upgrading to true monophonic amplifier m Massive transformer rated for 400 VA m 4-step gain control RadioFans.CN 收音机爱 好者资料库 Pure Class A power amplifier using power MOS-FET devices Fully balanced signal paths as found in high-quality instrumentation amplifiers. Further refined

3、MCS+ topology and current feedback design result in even better S/N ratio, distortion, and other performance parameters. Robust power supply and power MOS-FET devices in triple parallel push-pull configuration sustain an amazing 150 watts per channel into ultra-low 1-ohm impedance loads (with music

4、signals). Pure Class A power amplifiers from Accuphase have long been blending the purity of class A operation with the superior performance of power MOS-FETs. While building a string of outstanding amplifiers, Accuphase has accumulated a store of technical know-how that is second to none. The lates

5、t in this series, the A-30 is a pure class A stereo power amplifier based on the advanced technology of the model A-60. The A-30 employs the so-called instrumentation amplifier principle throughout. The signal handling stages feature further improved MCS+ topology and the renowned current feedback a

6、pproach. This has resulted in electrical characteristics that surpass even the demanding standards set by its predecessors. Employing only highest grade materials and strictly selected parts, the A-30 pursues the two most important goals of an amplifier: very low output impedance (Note 1) and consta

7、nt drive voltage (Note 2). The output stage of the A-30 features power MOS- FET devices renowned for their excellent sound and superior reliability. Because they have negative thermal characteristics, there is no danger of thermal “runaway” as exists with bipolar transistors. Operation remains total

8、ly stable even when the amplifier is running hot. Driving these devices in pure class A assures high-definition sound that brings out the finest nuances in the music. In pure class A operation, the power supply delivers a steady current, regardless of the presence or absence of a musical signal. Thi

9、s means that the amplifier remains unaffected by fluctuations in voltage and other external influences. On the other hand, it also means that the output stage generates considerable thermal energy. In the A-30, this is dissipated effectively by large heat sinks which provide ample capacity to remove

10、 the heat produced by the internal circuitry. The heavy-duty power supply easily sustains output levels of 120 watts into 2 ohms, 60 watts into 4 ohms, or 30 watts into 8 ohms (per channel). This linear progression demonstrates that the amplifier will be capable to drive even speakers with very low

11、impedance ratings or with pronounced impedance fluctuations. Stability remains excellent at all times. The amplifier also has the necessary reserves to handle musical transients that require considerable power in an instant. If even higher power is required, bridged mode turns the A-30 into a high-o

12、utput monophonic power amp. Output current (A) Output voltage (V) OUTPUT + B3 B3 INPUT +INPUT NFB NETWORK NFB NETWORK GAIN CONTROL CIRCUIT + + REGULATOR REGULATOR + B1 B1 B2 + B2 Q1 Q3 Q2 Q4 Q8 Q6 Q7 Q5Q9 Q17Q19 Q18Q20 Q21 Q22 Q23 Q24 Q25 Q26 Q13 Q11Q15 Q10Q14 Q12Q16 NFB NETWORK MCS+ Multiple Circui

13、t Summing ( ) Bias stabilizer circuit Bias stabilizer circuit Bias stabilizer circuit Bias stabilizer circuit Bias stabilizer circuit Fig. 1 Circuit diagram of amplifier section (one channel) Note 1:Low amplifier output impedance The load of a power amplifier, namely the loudspeaker, generates a cou

14、nterelectromotive force that can flow back into the amplifier via the NF loop. This phenomenon is influenced by fluctuations in speaker impedance and interferes with the drive performance of the amplifier. The output impedance of a power amplifier should therefore be made as low as possible by using

15、 output devices with high current capability. This absorbs the counterelectromotive force generated by the voice coil and prevents the occurrence of intermodulation distortion. Note 2:Constant drive voltage principle Even in the presence of a load with wildly fluctuating impedance, the ideal power a

16、mplifier should deliver a constant voltage signal to the load. Figure 2 shows the results of actual output voltage/output current measurements at different load impedances for the A-30. It can be clearly seen that output voltage is virtually constant at various loads, which means that current increa

17、ses in a linear fashion. Actual measurements of clipping power have yielded the following figures, which impressively demonstrate the more than ample performance of the A-30: 1 ohm: 175 watts, 2 ohms: 142 watts, 4 ohms: 94 watts, 8 ohms: 58 watts. 1-ohm rating is for music signals only. Fig. 2 Load

18、impedance vs. output power (Output voltage/output current) Instrumentation amp configuration allows fully balanced signal paths The A-30 features a new “instrumentation amplifier” principle whereby all signal paths from the inputs to the power amp stage are fully balanced. This results in excellent

19、CMRR (Common Mode Rejection Ratio) and minimal distortion. Another significant advantage is that external noise and other external influences are virtually shut out. The result is a drastic improvement in operation stability and reliability. Further refined MCS+ topology for even lower noise Accupha

20、ses original MCS (Multiple Circuit Summing) + INPUT NFB NETWORK GAIN CONTROL CIRCUIT NFB NETWORK OUTPUT +INPUT+ + Signal input stagePower amplifier stage Instrumentation amplifier configuration principle uses a number of identical circuits connected in parallel to achieve superior performance charac

21、teristics. MCS+ is a further refined version of this approach. Improvements in the bias circuitry of the input-stage buffer amplifier result in greater stability. This in turn makes it possible to extend the parallel operation approach to the class A drive stage of the current/voltage converter, the

22、reby further lowering the noise floor. Power MOS-FET output stage with triple parallel push-pull power units delivers 120 watts into 2 ohms, 60 watts into 4 ohms, or 30 watts into 8 ohms with outstanding linearity The output stage (Figure 1) uses power MOS-FETs. Three pairs of these devices are arra

23、nged in a parallel push-pull configuration for each channel. The result is stable operation with ideal power linearity even down to ultra-low impedances. The maximum power dissipation of one MOS-FET is 130 watts, but the actual power load per pair is much RadioFans.CN 收音机爱 好者资料库 lower, so that each

24、device is driven only in its low- power range where linearity is excellent. A music signal consists of a continuous succession of pulse waveforms. To prevent clipping on occasional momentary high-level pulses, the maximum clipping level of the A-30 is set to 50 watts per channel into 8 ohms (sine wa

25、ve output). Current feedback circuit topology assures excellent phase characteristics in high range In the A-30, the signal current rather than the more conventionally used voltage is used for feedback. Since the impedance at the current feedback point (current adder in Figure 3) is very low, there

26、is almost Buffer Current adder I-V converter Trans-impedance amplifier Amplifier Output Current NFB network Input Buffer + Input Gain(Large) (High)Frequency no phase shift. Phase compensation therefore can be kept at a minimum. A minimal amount of NFB results in maximum improvement of circuit parame

27、ters. The result is excellent transient response and superb sonic transparency, coupled with utterly natural e n e r g y b a l a n c e . Figure 4 shows f r e q u e n c y response for different gain settings of the c u r r e n t feedback amplifier. The graphs demonstrate that response remains uniform

28、 over a wide range. Robust power supply with large power transformer and high filtering capacity In any amplifier, the power supply plays a vital role since it acts as the original source for the output delivered to the speaker. The A-30 employs a large and highly efficient 400 VA power transformer.

29、 It is housed in an enclosure filled with a material that transmits heat and absorbs vibrations. This completely prevents any adverse influences on other circuit parts. Two aluminum e l e c t r o l y t i c capacitors rated for 47,000 F each serve to smooth out the pulsating direct current from the r

30、ectifier, providing more than ample filtering capacity. Fig. 3 Principle of current feedback amplifier Fig. 4 Frequency response with current feedback (Response remains uniform also when gain changes) n Power amplifier assembly with three parallel push-pull power MOS-FET pairs per channel mounted di

31、rectly to large heat sink, MCS+ circuitry, and current feedback amplifier Instrumentation amp type gain control minimizes residual noise The gain control switches gain in the first amplification stage that uses an instrumentation amp design. Four settings are available (MAX, 3 dB, 6 dB, 12 dB). With

32、 this approach, reducing gain also results in reduced noise. This is especially beneficial when using highly efficient speaker systems where the noise floor could be a problem. Bridged connection allows upgrading to a true monophonic amplifier with 300 watts into 2 ohms (music signals only), 240 wat

33、ts into 4 ohms, and 120 watts into 8 ohms Operation in bridged mode results in a monophonic amplifier with four times the power output than during stereo operation. This gives effortless dynamic power. Specifications and design subject to change without notice for improvements. K0405Y PRINTED IN JAP

34、AN 851-0139-00 (AD1) n n n n n Front panel n n n n n Rear panel GUARANTEED SPECIFICATIONS n Supplied accessories: AC power cord n n n n n Easy switching between dual mono/stereo/bridged mode In the dual mono position of the mode selector, the left-channel signal is supplied to both speaker terminals

35、, which can be used for bi- amping with dedicated low-range and high-range drivers. n n n n n Oversize speaker terminals also accept Y lugs and banana plugs The sturdy terminals can handle even very large gauge speaker cable. The connectors are made of extruded high- purity brass material and are go

36、ld-plated for ut- most reliability and mini- mum contact resistance. Y lugs and banana plugs can also be used. n n n n n Large analog power meters n n n n n Balanced connection prevents induced noise n n n n n PCB copper foil and all major signal path components are gold-plated n n n n n Buttons for

37、 meter on/off, meter sensitivity, and input selection Guaranteed specifications are measured according to EIA standard RS-490. m m m m m Continuous Average Output Power (20 - 20,000 Hz) Stereo operation150 watts per channel into 1 ohm () (both channels driven)120 watts per channel into 2 ohms 60 wat

38、ts per channel into 4 ohms 30 watts per channel into 8 ohms Monophonic operation300 watts into 2 ohms () (bridged connection)240 watts into 4 ohms 120 watts into 8 ohms Note: Load ratings marked () apply only to operation with music signals. m Total Harmonic DistortionStereo operation (both channels

39、 driven) 0.05%, with 2-ohm load 0.03%, with 4 to 16-ohm load Monophonic operation (bridged connection) 0.05%, with 4 to 16-ohm load m Intermodulation Distortion 0.005% m Frequency ResponseAt rated output:2020,000 Hz +0, 0.2 dB At 1 watt output:0.5160,000 Hz +0, 3.0 dB m Gain28.0 dB (GAIN selector in

40、 MAX position) (stereo and monophonic operation) m Gain SettingsMAX, 3 dB, 6 dB, 12 dB m Output Load ImpedanceStereo operation:2 to 16 ohms Monophonic operation: 4 to 16 ohms With music signals, load impedances of 1 (stereo) or 2 (mono) can be driven. m Damping Factor150 m Input Sensitivity (with 8-

41、ohm load, GAIN selector in MAX position) Stereo operation:0.57 V for rated continuous average output of 30 W 0.11V for 1 watt output Monophonic operation: 1.14Vfor rated continuous average output of 120 W 0.11V for 1 watt output m Input ImpedanceBalanced: 40 kilohmsUnbalanced: 20 kilohms m Signal-to

42、-Noise Ratio111 dB (GAIN selector in MAX position) (A-weighted, input shorted)118 dB (GAIN selector in 12 dB position) at rated output m Output Level Meters40 dB to +3 dB (dB/% scale) Logarithmic scale, with switching capability for meter operation and sensitivity m Power RequirementsAC 120 V/230 V

43、(Voltage as indicated on rear panel) 50/60 Hz m Power Consumption170 watts idle 260 watts accordance with IEC 60065 m Maximum DimensionsWidth465 mm(18-5/16”) Height170 mm(6-11/16”) Depth425 mm(16-3/4”) m Mass21.5 kg (47.4 lbs) net 26.0 kg (57.3 lbs) in shipping carton Unbalanced and balanced input c

44、onnectors Protection and meter circuit assembly High-quality, high-reliability parts ARight/left-channel output power meters (dB and % scale) BFunction indicators METER, 20 dB, UNBALANCED, BALANCED, BRIDGE CMeter operation/illumination switchONOFF DMeter sensitivity selector button (20 dB) EInput se

45、lector buttonUNBALANCEDBALANCED FPower switch GGain selector MAX3 dB6 dB12 dB HUnbalanced inputs IBalanced inputs a: Ground b: Inverted () c: Non-inverted (+) JMode selector DUAL MONONORMALBRIDGE KRight/left-channel speaker output terminals LAC power supply connector Remarks This product is available in versions for 120/230 V AC. Make sure that the voltage shown on the rear panel matches the AC line voltage in your area. The shape of the AC inlet and plug of the supplied power cord depends on the voltage rating and destination country.