Denon-AVR882-avr-sm维修电路原理图.pdf

《Denon-AVR882-avr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Denon-AVR882-avr-sm维修电路原理图.pdf（54页珍藏版）》请在收音机爱好者资料库上搜索。

1、Hi-Fi Component SERVICE MANUAL MODEL AVR-1802/882 AV SURROUND RECEIVER ? Some illustrations using in this service manual are slightly different from the actual set. For U.S.A., Canada, Europe, Asia, China, Hong Kong & Taiwan R.O.C. model 14-14, AKASAKA 4-CHOME, MINATO-KU, TOKYO 107-8011 JAPAN Teleph

2、one: 03 (3584) 8111 X0117 1174 NC 0109 RadioFans.CN 收音机爱 好者资料库 2 AVR-1802/882 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1)

3、 a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective. SPECIFICATIONS ? ? ? ? ? Audio section Power amplifier Rated output:Fron

4、t:80W + 80W(8/ohms, 20Hz 20kHz with 0.08% T.H.D) 115W + 115W (6/ohms, 1kHz with 0.7% T.H.D) (U.S.A., Canada & Europe Models) 130W + 130W (6/ohms, EIAJ) (Asia Model) Center:80W(8/ohms, 20Hz 20kHz with 0.08% T.H.D) 115W(6/ohms, 1kHz with 0.7% T.H.D) (U.S.A., Canada & Europe Models) 130W(6/ohms, EIAJ)

5、(Asia Model) Surround:80W + 80W(8/ohms, 20Hz 20kHz with 0.08% T.H.D) 115W + 115W (6/ohms, 1kHz with 0.7% T.H.D) (U.S.A., Canada & Europe Models) 130W + 130W (6/ohms, EIAJ) (Asia Model) Output terminals:Front:A or B 6 to 16/ohms A + B 12 to 16/ohms Center/Surround:6 to 16/ohms Analog LINE input - PRE

6、 OUT Input Sensitivity/input impedance:200mV/47k/kohms Frequency response:10Hz100kHz: + 1, 3dB (TONE DEFEAT ON) S/N ratio:100dB (IHF-A weighted) (TONE DEFEAT ON) ? ? ? ? ? Video section Standard video jacks Input/output level and impedance:1Vp-p, 75/ohms Frequency response:5Hz10MHz +1, 3dB S-video j

7、acks Input/output level and impedance:Y (brightness) signal 1Vp-p, 75/ohms C (color) signal 0.286Vp-p, 75/ohms Frequency response:5Hz10MHz +1, 3dB ? ? ? ? ? Tuner section Receiving range:FM (note: V at 75/ohms, 0dBf =1x10-15W)AM U.S.A. & Canada Models87.50MHz107.90MHz520kHz1710kHz Europe & Asia (for

8、 China) Models87.50MHz108.00MHz522kHz1611kHz Asia (for Multiple voltage) Models87.50MHz107.90MHz (0.2MHz steps)520kHz1710kHz (10kHz steps) 87.50MHz108.00MHz (0.05MHz steps)522kHz1611kHz (9kHz steps) Usable sensitivity:1.0 V (11.2dBf)18 V 50dB quieting sensitivity:MONO1.6 V (15.3dBf) STEREO23 V (38.5

9、dBf) S/N ratio:MONO80dB (IHF-A weighted) STEREO75dB (IHF-A weighted) Total harmonic distortion:MONO0.15% (1kHz) STEREO0.3% (1kHz) ? ? ? ? ? General Power supply: U.S.A., Canada ModelsAC120V, 60Hz Europe ModelAC230V, 50Hz Asia (for Multiple voltage) ModelAC115/230V, 50/60Hz Asia (for China) ModelAC22

10、0V, 50Hz Power consumption:4.5A (U.S.A. & Canada model), 230W (Europe & Asia model) Maximum external dimensions:434 (W) 171 (H) 417 (D)mm (17-3/32” 6-47/64” 16-7/16”) Mass:10.9kg (24lbs 0.5 oz) ? ? ? ? ? Remote control unit (RC-897) Batteries:R6P/AA Type(two batteries) External dimensions:54 (W) 172

11、.5 (H) 29 (D)mm (2-1/8” 6-51/64” 1-9/64”) Mass:120g (Approx. 4.2 oz) (including batteries) * For purposes of improvement, specifications and design are subject to change without notice. RadioFans.CN 收音机爱 好者资料库 3 AVR-1802/882 DISASSEMBLY (To reassemble reverse disassenbly) Top Cover Remove 6 screws 1

12、 and 3 screws 2, detach the Top Cover in the arrow direction. Top Cover Front Panel 1. Remove 2 screws 3. 2. Remove 4 screws 4. 3. Detach the Front Panel in the arrow direction. 2 1 1 Front Panel 3 3 4 Rear Panel 1. Remove cord bushing 5 from the Rear Panel. 2. Remove 36 screw 6. 3. Detach the Rear

13、Panel in the arrow direction. 5 6 6 6 Rear Panel 4 AVR-1802/882 ADJUSTMENT Tuner Section CONNECTION DIAGRAM OF MEASURING INSTRUMENTS ? FM STEREO MODULATOR FM SSG Digital Voltmeter 75ohm T402T403 IC402 VR402 TUNER BD R471 ? AM T402T403 IC402 TUNER BD R471 VR401 20+14 10dB FM ALIGNMENT InputOutputAdju

14、stment Step Alignment Item Tuning Frequency Setting TypeFrequency Input Level ModulationCouplingTypeConnect toPointsAdjust to 1 Center Adjustment 98.1MHz (98.0MHz) FM SSG98.1MHz60dB Antenna Terminal Digital Voltmeter R471T402 50mV 2Distortion 98.1MHz (98.0MHz) FM SSG98.1MHz60dB Mono 1kHz 100% Antenn

15、a Terminal Distortion Meter Output Terminal (L) T403 Minimum Distortion 3Repeat Steps 1 and 2 4Signal Level 98.1MHz (98.0MHz) FM SSG98.1MHz20dBOFF Antenna Terminal Light “TUNED” on FL Display VR402 AM ALIGNMENT OutputAdjustment Step Alignment Item FrequencyInput TypeConnect toPointsAdjust to Remarks

16、 1Signal Level 999 (1000) kHz AM SSGVR401 Light “TUNED” on FL Display SSG OUTPUT 74dB (EMF) 5 AVR-1802/882 Audio Section Idling Current Required measurement equipment : DC Voltmeter Preparation (1)Avoid direct blow from an air conditioner or an electric fan, and adjust the unit at normal room temper

17、eture 15 C 30 C (59 F 86 F). (2)Presetting G POWER (Power sourse switch)OFF G SPEAKER (Speaker terminal)No load (Do not connect speaker, dummy resistor, etc.) Adjustment (1)Remove top cover and set VR101, VR102, VR103, VR104, VR105 on Amp. Unit at full counterclockwise ( ) position. (2)Connect DC Vo

18、ltmeter to test points (FRONT-Lch: TP104, FRONT-Rch: TP105, CENTER ch: TP103, SURROUND-Lch: TP101, SURROUND-Rch: TP102). (3)Connect power cord to AC Line, and turn power switch ON. (4)Presetting.MASTER VOLUME : - counterclockwise ( min.) MODE: 5CH STEREO FUNCTION: CD (5)Within 2 minutes after the po

19、wer on, turn VR101 clockwise ( ) to adjust the TEST POINT voltage to 1.5 mV 0.5 mV DC. (6)After 10 minutes from the preset above, turn VR101 to set the voltage to 2.5 mV 0.5 mV DC. (7)Adjust the Variable Resistors of other channels in the same way. 87654321 A B C D E AVR-1802/882 6 LEVEL DIAGRAM 7 A

20、VR-1802/882 123456 7 8 9 10 11 33 32 31 30 29 282726252423 34 35 36 37 38 39 4041424344 17 16 15 14 13 12 18 19 20 21 22 A1,SCDIN RD,R/W,EMOE,GPIO11 WR,DS,EMWR,GPIO10 AUDATA3,XMT958 DGND1 VD1 MCLK SCLK LRCLK AUDATA0 AUDATA1 AUDATA2 DC DD RESET AGND VA FILT1 FILT2 CLKSEL CLKIN CMPREQ,LRCLKN2 CS SCDIO

21、,SCDOUT,PSEL,GPIO9 ABOOT,INTREQ EXTMEM,GPIO8 SDATAN1 VD3 DGND3 SCLKN1,STCCLK2 LRCLKN1 CMPDAT,SDATAN2,RCV958 CMPCLK,SCLKN2 A0,SCCLK DATA7,EMAD7,GPIO7 DATA6,EMAD6,GPIO6 DATA5,EMAD5,GPIO5 DATA4,EMAD4,GPIO4 VD2 DGND2 DATA3,EMAD3,GPIO3 DATA2,EMAD2,GPIO2 DATA1,EMAD1,GPIO1 DATA0,EMAD0,GPIO0 SEMICONDUCTORS

22、? ? ? ? ? ICs CS493263-CL (AU: IC812) CS493263-CL Terminal Function 1VD1Digital positive supply 2DGND1Digital supply ground 3AUDATA3, XMT958SPDIF transmitter output, Digital audio output 3 4WR, DS, EMWR, GPIO10Host write strobe or host data strobe or external memory write enable or general purpose i

23、nput & output number 10 5RD, R/W, EMOE, GPIO11Host parallel output enable or host parallel R/W or external memory output enable or general purpose input & output number11 6A1, SCDINHost address bit one or SPI serial control data input 7A0, SCCLKHost parallel address bit zero or serial control port c

24、lock 8DATA7, EMAD7, GPIO7 9DATA6, EMAD6, GPIO6 10DATA5, EMAD5, GPIO5 11DATA4, EMAD4, GPIO4 12VD2Digital positive supply 13DGND2Digital supply ground 14DATA3, EMAD3, GPIO3 15DATA2, EMAD2, GPIO2 16DATA1, EMAD1, GPIO1 17DATA0, EMAD0, GPIO0 18CSHost parallel chip select, host serial SPI chip select 19SC

25、DIO, SCDOUT, PSEL, GPIO9Serial control port data input and output, parallel port type select 20INTREQ, ABOOTControl port interrupt request, automatic boot enable 21EXTMEM, GPIO8External memory chip select or general purpose input & output number 8 22SDATAN1PCM audio data input number one 23VD3Digita

26、l positive supply 24DGND3Digital supply ground 25SCLKN1, STCCLK2PCM audio input bit clock 26LRCLKN1PCM audio input sample rate clock 27CMPDAT, SDATAN2, RCV958PCM audio data input number two 28CMPCLK, SCLKN2PCM audio input bit clock 29CMPREQ, LRCLKN2PCM audio input sample rate clock 30CLKINMaster clo

27、ck input 31CLKSELDSP clock select 32FILT2Phase locked loop filter 33FILT1Phase locked loop filter 34VAAnalog positive supply 35AGNDAnalog supply ground 36RESETMaster reset input 37DDReserved 38DCReserved 39AUDATA2Digital audio output 2 40AUDATA1Digital audio output 1 41AUDATA0Digital audio output 0

28、42LRCLKAudio output sample rate clock 43SCLKAudio output bit clock 44MCLKAudio master clock Pin No. Pin NameFunction 8 AVR-1802/882 LC89055W (IC810) LC89055W Terminal Function 1DISELIData input terminal (select input pin of DIN0, DIN1) 2DOUTOInput bi-phase data through output terminal 3DIN0IAmp buil

29、t-in coaxial/optical input correspond data input terminal 4DIN1IAmp built-in coaxial/optical input correspond data input terminal 5DIN2IOptical input correspond data input terminal 6DGNDDigital GND 7DVDDDigital power supply 8RIVCO gain control input terminal 9VINIVCO free-run frequency setting input

30、 terminal 10LPFOPLL loop filter setting terminal 11AVDDAnalog power supply 12AGNDAnalog GND 13CKOUTOClock output terminal (256fs, 384fs, 512fs, Xtal osc., VCO free-run osc.) 14BCKO64fs clock output terminal 15LRCKOfs clock output terminal (L: Rch, H: Lch, I2S: Reverse) 16DATAOOData output terminal 1

31、7XSTATEOInput data detecting result output terminal 18DGNDDigital GND 19DVDDDigital power supply 20XMCKOXtal osc. clock output terminal (24.576MHz or 12.288MHz) 21XOUTOXtal osc. connection output terminal 22XINIXtal osc. connection input terminal, external signal input possible (24.576MHz or 12.288M

32、Hz) 23EMPHAOEmphasis information output terminal of channel status 24AUDIOOBit1 output terminal of channel status 25CSFLAGOTop 40bit revise flag output terminal of channel status 26F0/P0/C0OInput fs cal. sig. out/data type out/input word inf. output terminal 27F1/P1/C1OInput fs cal. sig. out/data ty

33、pe out/input word inf. output terminal 28F2/P2/C2OInput fs cal. sig. out/data type out/input word inf. output terminal 29VF/P3/C3OValidity flag out/data type out/input word inf. output terminal 30DVDDDigital power supply 31DGNDDigital GND 32AUTOONon PCM burst data transfer detect sig. output termina

34、l 33BPSYNCONon PCM burst data preamble Pa, Pb, Pc, Pd sync sig. output terminal 34ERROROPLL lock error, data error flag output terminal 35DOOCPU/IFD read data output terminal 36DIICPU I/F write data input terminal 37CEICPU I/F chip enable input terminal 38CLICPU I/F chip enable input terminal 39XSEL

35、IFrequency select input pin of XIN Xtal osc. (24.576MHz or 12.288MHz) 40MODE0IMode setting input terminal 41MODE1IMode setting input terminal 42DGNDDigital GND 43DVDDDigital power supply 44DOSEL0IData output format select input terminal 45DOSEL1IData output format select input terminal 46CKSEL0IOutp

36、ut clock select input terminal 47CKSEL1IOutput clock select input terminal 48XMODEIReset input terminal Pin No. Pin NameFunctionI/O ? For latch-up countermeasure, set digital (DVDD) and analog (AVDD) power on/off in the same timing. 9 AVR-1802/882 AK4527BVQ (IC813) AK4527BVQ Terminal Function 1 2 3

37、4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 33 32 31 30 29 28 27 26 25 24 23 44 43 42 41 40 39 38 37 36 35 34 SDOS I2C SMUTE BICK L RCK SDTI1 DAUX DFS DZ F2/ OV F RIN+ RIN ROUT1 L 0OP1 L 0OP0/ SDA/ CDTI DIF1/ SCL / CCL K DIF0/ CSN P/ S MCL K DZ F1 AV SS AV DD V REFH V COM NC TV DD PDN TST CAD

38、1 L IN+ L IN L OUT1 ROUT2 L OUT2 ROUT3 L OUT3 SDTI2 SDTI3 SDTO DZ FE DV DD DV SS NC ADIF CAD0 Top View AK4527BVQ Pin No. Pin NameI/OFunction 1SDOSISDTO source select pin, L: Internal ADC output, H: DAUX input 2I2CISerial control mode select pin, L: 3-core serial, H: I 2C bus 3SMUTEISoft mute pin, H:

39、 Soft mute start, L: Release 4BICKIAudio serial data clock pin 5LRCKIInput channel clock pin 6SDTI1IDAC1 audio serial data input pin 7SDTI2IDAC2 audio serial data input pin 8SDTI3IDAC3 audio serial data input pin 9SDTOOAudio serial data output pin 10DAUXIAuxiliary audio serial data input pin 11DFSID

40、ouble speed sampling mode pin, L: Normal, H: Double 12NCNo Connect, No internal bonding 13DZFEIZero input detect enable pin 14TVDDPower pin for output buffer, 2.7V5.5V 15DVDDDigital power pin, 4.5V5.5V 16DVssDigital GND pin, 0V 17PDNIPower down & reset pin, L: Powered-down and register initialized,

41、Reset with PDN when switching CAD0-1 18TSTITest pin, connected to DVSS 19NCNo Connect, No internal bonding 20ADIFIAnalog Input Format Select pin 21CAD1IChip address-1 pin 22CAD0IChip address-0 pin 23LOUT3ODAC3L channel analog out pin 24ROUT3ODAC3R channel analog out pin 25LOUT2ODAC2L channel analog

42、out pin 26ROUT2ODAC2R channel analog out pin 27LOUT1ODAC1L channel analog out pin 28ROUT1ODAC1R channel analog out pin 29LIN-IL-ch analog inverted input pin 30LIN+IL-ch analog non-inverted input pin 31RIN-IR-ch analog inverted input pin 32RIN+IR-ch analog non-inverted input pin 33DZF2/OVFO0 input de

43、tect 2 pin/Analog input overflow detect pin 34VCOMOCommon V-out pin, AVDD/2, connect large capacitor to avoid noise 35VREFHIRef. V input pin, AVDD 36AVDDAnalog GND pin, 4.5V5.5V 37AVssAnalog GND pin, 0V 38DZF1O0 input detect pin, H: Input data of G1 is 8192 times “0” in a raw or RSTN bit “0”, L: Whe

44、n P/S= “0” 39MCLKIMaster clock input pin 40P/SIParallel/Serial select pin, L: Serial control DIF0IAudio data I/F format 0 pin (parallel control) 41 CSNIChip select pin (3-wire serial control), connect to DVDD when I 2C bus control DIFIIAudio data I/F format 1 pin (parallel control) 42 SCL/CCLKIContr

45、ol data clock pin (serial control), I 2C=”L”: CCLK (3-wire serial), I2C=”H”: SCL (I2C bus) LOOP0ILoop back mode 0 pin (parallel control), effects digital loop back ADC to all DAC 43 SDA/CDTII/OControl data input pin (serial control), I 2C=”L”: CCTI (3-wire serial), I2C=”H” SDA (I2C bus) 44LOOP1ILoop

46、 back mode 1 pin, from SDT1 to all DAC 10 AVR-1802/882 1 2 3 4 5 6 7 8 18 17 16 15 14 13 12 11Q3 VDD OE Q7 Q8 Q11 Q10 Q9 Q6 VSS DATA CLOCK LCK Q0 Q1 Q2 910Q4Q5 CONTROL CIRCUIT 12-bit SHIFT RESISTER 12-bit STRAGE RESISTER OUTPUT BUFFER (OPEN DRAIN) BU2090F (IC302, 602) 1 MM74LCX244 (IC818,819) RC1117

47、S25T (IC820) RC1117S33ST (IC811) 2 3 2 ADJ/GND OUT IN MM74HC151 (IC832) VOUT FRONT VIEW LA1266 (IC402) 10 4 13 8 19 15 17 18 14 21 22 ? ? ? ? ? ? 511 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 2 ? ? ? ? ? ? ? 6 ? ? ? ? 7 ? ? ? 23 ? ? ? ? ? ? ? ? ? ? ? ? 24 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 16 ? ? ? ? ? ?

48、 ? ? ? ? ? ? ? 12 20 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 9 13 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 201918171615141312 987561 21 LA3401 (IC403) 22 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?

49、 ? ? ? ? ? ? ? ? ? ? ? ! ? ? # ? ? ? ? ? ? ! ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? $ ? ? ? ? ? % 234 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? % 1011 LC72131 (IC401) # & ! & # ? # ? # ( ) # * * # ) ( # ? # ? # & # !# # ? ? ? ? ? ? ? ? ? ? ? ? ? # ? ? & ? ? ? ? ? ? ? # ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? & ? ? ? ? ? + + ? ? ? ? TDA7330BD (IC202) TOP VIEW PORMUXIN TMVREF FSELCOMP T2FIL