Onkyo-BDSP809-br-sm维修电路原理图.pdf

《Onkyo-BDSP809-br-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Onkyo-BDSP809-br-sm维修电路原理图.pdf（69页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL Ref. No. 4303 082011 BLU-RAY DISC PLAYER MODEL BD-SP809 Black model B CDC1AN120V AC, 60Hz RC-818DV SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK COMPONENTS IDENTIFIED BY MARK #ON THE SCHEMATIC DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR RISK OF FIRE AND ELECTRIC S

2、HOCK. REPLACE THESE COMPONENTS WITH ONKYO PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL. MAKE LEAKAGE-CURRENT OR RESISTANCE MEASUREMENTS TO DETERMINE THAT EXPOSED PARTS ARE ACCEPTABLY INSULATED FROM THE SUPPLY CIRCUIT BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER. ON THE SCHEMATIC DIAGRAM

3、 AND IN THE PARTS LIST ARE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. REPLACE THESE COMPONENTS WITH ONKYO PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL. MAKE LEAKAGE-CURRENT OR RESISTANCE MEASUREMENTS TO DETERMINE THAT EXPOSED PARTS ARE ACCEPTABLY INSULATED FROM THE SUPPLY CIRCUIT BEFOR

4、E RETURNING THE APPLIANCE TO THE CUSTOMER. BD-SP809 RadioFans.CN 收音机爱 好者资料库 TABLE OF CONTENTS Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1-1 Laser Beam Safety Precautions . . . .

5、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2-1 Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3-1 Standard Notes for Servic

6、ing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4-1 Cabinet Disassembly Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5-1 How to Initi

7、alize the BLU-RAY Disc Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6-1 Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-7-1 Adju

8、stment Instructions for BD Main CBA or BD Mechanism Assembly Replacement . . . . . . . . . . . . . . . . . .1-8-1 Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-9-1 Home Network (DLNA) E

9、rror Code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-10-1 Block Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-11-1 Schemat

10、ic Diagrams / CBA and Test Points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-12-1 Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-13

11、-1 Mechanical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-14-1 Electrical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12、 . . . . . . . . . . . .1-15-1 Precautions on 3D video images This unit supports Blu-ray 3D. When servicing problems related to 3D image output, the following equipments are needed. - 3D capable TV - 3D compatible HDMI cable - 3D glasses - Blu-ray 3D disc Manufactured under license from Dolby Labora

13、tories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. RadioFans.CN 收音机爱 好者资料库 1-1-1E5WB0SP SPECIFICATIONS General Signal systemNTSC Color Power requirementsAC120 V, 60 Hz Power consumption22 W (standby: 0.5 W) Dimensions (width x height x depth)17-1/8 x 4-1/8 x 12-5/16 inches (

14、435 x 104 x 313 mm) Weight10.4 lbs (4.7 kg) Operating temperature 41 F(5 C) to 104 F(40 C) Operating humidityLess than 80 % (no condensation) Audio BD Linear Audio4 Hz88 kHz (192 kHz) DVD Linear Audio4 Hz44 kHz (96 kHz), 4 Hz22 kHz (48 kHz) Audio CD4 Hz20 kHz (44.1 kHz) Signal to Noise Ratio100 dB A

15、udio Dynamic Range98 dB THD (Total Harmonic Distortion)0.005 % (1 kHz) Terminals USB input TYPE A USB 2.0 Bus power current: MAX. 500 mA Audio output (Analog) RCA jack x 2L/R: 2 Vrms (output impedance: more than 1 k?) Video output RCA jack x 11Vp-p (75?) Component video output RCA jack x 3 Y: 1 Vp-p

16、 (75 ?) PB: 700 mVp-p (75 ?) PR: 700 mVp-p (75 ?) Audio output (Digital) RCA jack x 1 Optical jack x 1 500 mVp-p (75 ?) Digital connector HDMI output HDMI jack x 2Video: 480i, 480p, 720p, 1080i, 1080p, 1080p24 / Audio ETHERNET terminal10BASE-T/100BASE-TX D Note The specifications and design of this

17、product are subject to change without notice. 1-2-1B4NLBSP LASER BEAM SAFETY PRECAUTIONS This BD player uses a pickup that emits a laser beam. The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 11.8 inches (30 cm) away f

18、rom the pickup lens when the diode is turned on. Do not look directly at the laser beam. CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result in hazardous radiation exposure. Location: Inside Top of BD mechanism. Do not look directly at the lase

19、r beam coming from the pickup or allow it to strike against your skin. Drive Mechanism Assembly Laser Beam Radiation Laser Pickup Turntable 1-3-1BDN_ISP IMPORTANT SAFETY PRECAUTIONS Product Safety Notice Some electrical and mechanical parts have special safety-related characteristics which are often

20、 not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by a # on schematics and in parts lists. Use of a substitute replaceme

21、nt that does not have the same safety characteristics as the recommended replacement part might create shock, fire, and/or other hazards. The Products Safety is under review continuously and new instructions are issued whenever appropriate. Prior to shipment from the factory, our products are carefu

22、lly inspected to confirm with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced. Precautions during Servicing A.

23、Parts identified by the # symbol are critical for safety. Replace only with part number specified. B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements. Example

24、s: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc. C. Use specified internal wiring. Note especially: 1) Wires covered with PVC tubing 2) Double insulated wires 3) High voltage leads D. Use specified insulating materials for hazardous live parts. Note especially

25、: 1) Insulation tape 2) PVC tubing 3) Spacers 4) Insulators for transistors E. When replacing AC primary side components (transformers, power cord, etc.), wrap ends of wires securely about the terminals before soldering. F.Observe that the wires do not contact heat producing parts (heat sinks, oxide

26、 metal film resistors, fusible resistors, etc.). G. Check that replaced wires do not contact sharp edges or pointed parts. H. When a power cord has been replaced, check that 1113 lb (56 kg) of force in any direction will not loosen it. I.Also check areas surrounding repaired locations. J.Be careful

27、that foreign objects (screws, solder droplets, etc.) do not remain inside the set. K. When connecting or disconnecting the internal connectors, first, disconnect the AC plug from the AC outlet. L.When reassembling, be sure to use the original screws or specified screws listed in the parts list. M. T

28、his unit is classified as a CLASS 1 LASER PRODUCT. 1-3-2BDN_ISP Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, and wires have been returned to their original positions. Afterwards, do the following tests and co

29、nfirm the specified values to verify compliance with safety standards. 1. Clearance Distance When replacing primary circuit components, confirm specified clearance distance (d) and (d) between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1) Table 1: Ratings for

30、 selected area Note:This table is unofficial and for reference only. Be sure to confirm the precise values. 2. Leakage Current Test Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna termina

31、ls, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below. Measuring Method (Power ON): Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to m

32、easure across the terminals of load Z. See Fig. 2 and the following table. Table 2: Leakage current ratings for selected areas Note:This table is unofficial and for reference only. Be sure to confirm the precise values. AC Line VoltageClearance Distance (d), (d) 120 V 3mm(d) 4mm(d) AC Line VoltageLo

33、ad ZLeakage Current (i) One side of power cord plug prongs (B) to: 120 V 2k RES. Connected in parallel i0.7mA AC Peak i2mA DC RF or Antenna terminals 50k RES. Connected in parallel i0.7mA AC Peak i2mA DC A/V Input, Output Chassis or Secondary Conductor Primary Circuit Fig. 1 dd Fig. 2 AC Voltmeter (

34、High Impedance) Exposed Accessible Part B One side of Power Cord Plug Prongs Z 1-4-1BDN_SN STANDARD NOTES FOR SERVICING Circuit Board Indications 1.The output pin of the 3 pin Regulator ICs is indicated as shown. 2.For other ICs, pin 1 and every fifth pin are indicated as shown. 3.The 1st pin of eve

35、ry male connector is indicated as shown. Instructions for Connectors 1.When you connect or disconnect the FFC (Flexible Foil Connector) cable, be sure to first disconnect the AC cord. 2.FFC (Flexible Foil Connector) cable should be inserted parallel into the connector, not at an angle. Pb (Lead) Fre

36、e Solder When soldering, be sure to use the Pb free solder. How to Remove / Install Flat Pack-IC 1. Removal With Hot-Air Flat Pack-IC Desoldering Machine: 1.Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1) 2.Remove the

37、flat pack-IC with tweezers while applying the hot air. 3.Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) 4.Release the flat pack-IC from

38、the CBA using tweezers. (Fig. S-1-6) CAUTION: 1.The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC. 2.Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage

39、to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2) Top View OutIn Bottom View Input 5 10 Pin 1 Pin 1 FFC Cable Connector CBA * Be careful to avoid a short circuit. Fig. S-1-1 1-4-2BDN_SN 3.The flat pack-IC on the CBA is affixed with

40、 glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it. With Soldering Iron: 1.Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can

41、remove it easily. (Fig. S-1-3) 2.Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4) 3.Bottom of the flat pack-IC is fixed with

42、 glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) 4.Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) Hot-air Flat Pack-IC Desoldering Machine CBA Flat Pack-IC Tw

43、eezers Masking Tape Fig. S-1-2 Flat Pack-IC Desoldering Braid Soldering Iron Fig. S-1-3 Fine Tip Soldering Iron Sharp Pin Fig. S-1-4 1-4-3BDN_SN With Iron Wire: 1.Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of th

44、e flat pack-IC, you can remove it easily. (Fig. S-1-3) 2.Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5. 3.While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pad

45、s as shown in Fig. S-1-5. 4.Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) 5.Release the flat pack-IC from the CBA using tweezers. (Fig.

46、 S-1-6) Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied. 2. Installation 1.Using desoldering braid, remove the solder from th

47、e foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily. 2.The “ I ” mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the pin 1 on the PCB when positioning for installation. Then presolder the four corners of th

48、e flat pack-IC. (See Fig. S-1-8.) 3.Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges. To Solid Mounting Point Soldering Iron Iron Wire or Hot Air Blower Fig. S-1-5 Fine Tip Soldering Iron CBA Flat Pack-IC Tweezers Fig. S-1-6 Example : Pin 1 of the Flat Pack-IC i

49、s indicated by a mark. Fig. S-1-7 Presolder CBA Flat Pack-IC Fig. S-1-8 1-4-4BDN_SN Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 M) that is properly grounded to remove any static electricity that may be charged on the body. 2. Ground for Workbench Be sure to place a conductive sheet or copper plate with proper grounding (1 M) on the workbench or