SONYst-se500 电路图 维修原理图.pdf

《SONYst-se500 电路图 维修原理图.pdf》由会员分享，可在线阅读，更多相关《SONYst-se500 电路图 维修原理图.pdf（52页珍藏版）》请在收音机爱好者资料库上搜索。

1、1GB FM Stereo FM-AM Tuner 1998 by Sony Corporation 3-865-570-31(1) Operating instructions Instrukcja obsugi GB PL RU ST-SE500 RadioFans.CN 2GB WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to q

2、ualified personnel only. Precautions On safety Should any liquid or solid object fall into the unit, unplug the unit and have the unit checked by qualified personnel before operating it any further. On power sources Before operating the unit, be sure that the operating voltage of your unit is identi

3、cal with that of your local power supply. Unplug the unit from the wall outlet if it is not to be used for an extended period of time. To disconnect the cord, pull it out by grasping the plug. Never pull the cord itself. AC power cord must be changed only at the qualified service shop. On placement

4、Place the unit in a location with adequate ventilation to prevent heat buildup and prolong the life of its components. Do not place the unit near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock. Do not place anything on top of the cabinet which might block

5、the ventilation holes and cause malfunctions. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. On cleaning the cabinet Clean the cabinet, panels and controls with a soft cloth lightly moistened with a mild detergent solution. Do not use any type of abrasive p

6、ad, scouring powder or solvent such as alcohol or benzine. On repacking Do not throw away the carton and the packing material. This makes an ideal container when transporting the unit. When shipping the unit, repack it as it was packed at the factory. If you have any question or problem concerning y

7、our unit that is not covered in this manual, please consult your nearest Sony dealer. RadioFans.CN 3GB TABLE OF CONTENTS Getting Started Unpacking 4 Hooking up the System 4 Selecting the German Display 6 Storing FM Stations Automatically (Auto-betical select) 6 Basic Operations Receiving Preset Stat

8、ions 7 Advanced Tuner Operations About the Menu Entry System 8 Customizing the Display 8 Receiving Broadcasts 9 Tips for Better FM Reception 10 Presetting Radio Stations 10 Naming the Preset Stations 11 Organizing the Preset Stations 12 Using the Radio Data System (RDS) 13 Additional Information Tro

9、ubleshooting 15 Specifications 15 Index 16 GB Welcome! Thank you for purchasing the Sony FM Stereo FM/AM Tuner. Before operating the unit, please read this manual thoroughly and retain it for future reference. Convention The following icon is used in this manual: Indicates hints and tips for making

10、the task easier. RadioFans.CN 4GB Unpacking Check that you received the following items with the tuner: Audio cord (1) AM loop aerial (1) FM wire aerial (1) EON connecting cord (1) Getting Started around the frame of the aerial. Be careful to unwrap only the braided section of the lead wire. Do not

11、unwrap more than 3 lengths of the lead wire. Also, be careful not to unbraid the lead wire. 3Assemble the supplied aerial as shown below. 4Connect the AM loop aerial to the AM terminals on the back of this unit. 5Adjust the aerial direction for the best reception. The AM loop aerial has a directivit

12、y which detects the signal from some angles more strongly than others. Set the aerial to the orientation which provides the best receiving condition. If a high pitched noise (beat noise) occurs when recording AM broadcasts, adjust the position of the AM loop aerial so that the noise disappears. If y

13、ou live in a building constructed of reinforced concrete, or with a steel frame, you may not be able to achieve good reception since the radio waves become weaker indoors. In this case, we recommend connecting an optional aerial such as the Sony AN-1. For stations that are difficult to receive Try r

14、epositioning the loop aerial while tuning. Placing the supplied AM loop aerial near a window will help improve reception quality. Hooking up the System Before you get started Turn off the power to all components before making any connections. Do not connect the mains lead until all of the connection

15、s are completed. Be sure to make connections firmly to avoid hum and noise. When connecting an audio cord, be sure to match the colour-coded pins to the appropriate jacks: White (left) to White; and Red (right) to Red. AM aerial hookups This section describes how to connect the supplied AM loop aeri

16、al. For the specific location of the AM ANTENNA terminals, see the illustration below. What will I need? AM loop aerial (supplied) (1) 1Before assembling the supplied aerial, pull the lead wire out from the slot in the aerial frame. 2Unwrap 3 lengths of the braided lead wire from AM loop aerial ANTE

17、NNA FM 75 COAXIAL AM y AM ANTENNA RadioFans.CN 5GB FM aerial hookups With an FM outdoor aerial, you can obtain a higher FM broadcast sound quality. We recommend that you use the supplied FM wire aerial only temporarily until you install an FM outdoor aerial. For the specific location of the FM ANTEN

18、NA terminal, see the illustration below. What will I need? FM wire aerial (supplied) (1) FM outdoor aerial (not supplied) (1) and 75-ohm coaxial cable with IEC female type connector (not supplied) (1) Connect the supplied FM wire aerial or an FM outdoor aerial (not supplied) to one of the FM termina

19、ls on the back of this unit. Connecting a ground wire If you connect an outdoor aerial, be sure to connect a earth lead (not supplied) to the AM ANTENNA y terminal (in addition to the AM loop aerial) for lightning protection. Getting Started FM ANTENNA IEC female type connector Amplifier hookups Con

20、nect the tuner to an amplifier. Be sure to turn off the power to both components before connection. For the specific location of the terminals, see the illustration below. What cables will I need? Audio cord (supplied) (1) Connect the white plugs to the white (L) jacks and the red plugs to the red (

21、R) jacks. Insert the plugs completely into the jacks; incomplete connections may cause noise. EON CONTROL Red (R) White (L)White (L) Red (R) TUNER IN RL RL LINE OUT Amplifier Tuner If you have a Sony amplifier equipped with an EON CONTROL IN terminal Use the supplied EON connecting cord to connect t

22、he EON CONTROL OUT terminal on the tuner to the EON CONTROL IN terminal on your amplifier. This lets you use the EON function (see page 13) when listening to other components. Mains lead hookup Connect the mains lead to a wall outlet after completing all of the previous connections. Amplifier Tuner

23、EON CONTROL OUT EON CONTROL IN / ANTENNA FM 75 COAXIAL AM y FM wire aerial ANTENNA FM 75 COAXIAL AM y FM outdoor aerial IEC female type connector LINE OUT to a wall outlet RadioFans.CN 6GB Storing FM Stations Automatically (Auto-betical select) With “Auto-betical select” you can automatically store

24、up to 30 FM and FM RDS stations in alphabetical order without redundancy. Additionally, “Auto-betical select” only stores the stations with the clearest signals. If you want to store FM or AM (MW and LW) stations one by one, see “Receiving Broadcasts” on page 9 and “Presetting Radio Stations” on pag

25、e 10. 1Press POWER to turn on the tuner. 2Turn on the amplifier and select the TUNER mode. 3Press AUTO-BETICAL SELECT. “Yes” and “No” appear in the display. 4Turn TUNING/SELECT to select “Yes”. 5Press AUTO-BETICAL SELECT again. The tuner scans and stores all the FM and FM RDS stations in the broadca

26、st area. For RDS stations, the tuner first checks for stations broadcasting the same programme, then stores only the one with the clearest signal. The selected RDS stations are sorted alphabetically by their Programme Service name, then assigned a two-character preset code. For more details on RDS,

27、see page 13. Regular FM stations are assigned two-character preset codes and stored after the RDS stations. To change the location of, or erase, a preset station See “Organizing the Preset Stations” on page 12. Notes If you move to another area, repeat this procedure to store stations in your new ar

28、ea. For details on tuning stored stations, see page 7. The FM MODE setting is also stored along with the station. If you move the aerial after storing stations using Auto- betical select, the stored settings may no longer be valid. If this happens, store the stations again. Getting Started Selecting

29、 the German Display You can choose either an English or a German language display. The factory preset language is English. To change the display to German, follow the steps below. 1Press POWER to turn off the tuner. 2While holding down the “2” button, press POWER to turn on the tuner . “Deutsch” app

30、ears in the display. To return to the English display Repeat this procedure. “English” appears in the display. POWER AUTO-BETICAL SELECT TUNING/SELECT POWER 2 RadioFans.CN 7GB Make sure youve hooked up the tuner and preset stations. (See pages 4 - 5 for hookups and page 6 or 10 for presetting.) Turn

31、 on the amplifier and select the TUNER mode. Press POWER to turn on the tuner. Press SHIFT to select A, B, or C. Press the preset number you want (1 - 0). Receiving Preset Stations This section shows you how to receive preset stations. To check broadcasts by scanning the preset stations 5 3 2 1 4 To

32、 tune in a non-preset station, see “Receiving Broadcasts” on page 9. Basic Operations POWER S EON Link System AUTO-BETICAL SELECT MEMORYFM MODEBAND TANEWS/INFOPTYDISPLAY EON SHIFT1234567890DIRECT MENURETURN CHARACTER TUNE MODE TUNING/ SELECT ENTER FM STEREO/FM-AM TUNER ST-SE500 3 45 1Press TUNE MODE

33、 repeatedly so that “PRESET” appears in the display. 2Turn TUNING/SELECT. Each time you turn TUNING/SELECT, a preset station is received and the settings (preset code, frequency, and station name, etc.) appear in the display. The signal meter indicates the strength of the broadcast signal. 0DIRECT M

34、ENURETURN CHARACTER TUNE MODE TUNING/ SELECT ENTER FM STEREO/FM-AM TUNER ST-SE5 00 TUNING/SELECTTUNE MODE RadioFans.CN 8GB About the Menu Entry System This tuner uses a menu entry system which allows you to operate various functions by following messages on the display. Use the following controls fo

35、r menu operation. Advanced Tuner Operations TUNING/SELECT ENTERMENU RETURN Use the MENU button TUNING/SELECT knob ENTER button RETURN button To: enter the menu mode. display different items or settings. select the currently displayed item or setting. return to a previous stage in the menu mode. Cust

36、omizing the Display You can choose the appearance of the display from one of the following four display modes. 1Press MENU, then turn TUNING/SELECT until “Disp-Mode” appears in the display. 2Press ENTER. “Select” appears in the display. 3Turn TUNING/SELECT to select a display mode. Full Display/Full

37、 Brightness . Full Display/Dimmed . Minimal Display/Full Brightness . Minimal Display/Dimmed 4Press ENTER. The setting remains in effect until you change it again. If you press one of the buttons on the main unit, the minimal display changes to the full display with the selected brightness. After ab

38、out 4 seconds, the display returns to the display mode you selected. TUNING/SELECT ENTERMENU RadioFans.CN 9GB Receiving Broadcasts This tuner lets you enter a stations frequency directly by using the numeric buttons (direct tuning). If you dont know the frequency of the station you want, see “Receiv

39、ing broadcasts by scanning stations (Automatic tuning)”. Before you begin, make sure you have: Connected an FM/AM aerial to the tuner as indicated on page 4. 1Press BAND to select FM, MW, or LW. 2Press DIRECT. 3Press the numeric buttons to enter the frequency. Example 1: FM 102.50 MHz Example 2: AM

40、1350 kHz To receive other stations Repeat Steps 1 to 3. When you tune in AM (MW and LW) stations Adjust the direction of the AM loop aerial for optimum reception. If the STEREO indicator remains off Press FM MODE when an FM stereo broadcast is received. If an FM stereo programme is distorted The STE

41、REO indicator flashes. Press FM MODE to change to monaural (MONO). You will not have the stereo effect but the distortion will be reduced. To return to stereo mode, press this button again. If you cannot tune in a station and the entered numbers are flashing Make sure youve entered the right frequen

42、cy. If not, press DIRECT and reenter the frequency you want. If the entered numbers still flash, the frequency is not used in your area. If you enter a frequency not covered by the tuning interval The entered value is automatically rounded up or down to the closest covered value. Tuning intervals fo

43、r direct tuning are: FM: 50 kHz intervals AM: 9 kHz intervals (MW), 1 kHz interval (LW) Receiving broadcasts by scanning stations (Automatic tuning) With automatic tuning you can quickly tune in a station without having to know its frequency. 1Press BAND to choose either FM, MW, or LW. 2Press TUNE M

44、ODE so that “AUTO TUNING” appears in the display. 3Turn TUNING/SELECT slightly and release it when the frequency numbers start changing. Turn the knob to the right for a higher frequency; turn it to the left for a lower frequency. When the tuner locates a station, it stops automatically, “TUNED” app

45、ears in the display. The signal meter indicates the strength of the broadcast signal. 4Repeat step 3 until you tune in the appropriate station. To store the station, see “Presetting Radio Stations” on page 10. If you cannot tune in the station you want(Manual Tuning) With manual tuning you can searc

46、h through all stations broadcasting on each band, and tune in stations with extremely weak signals that you might not be able to receive with automatic tuning. 1 Press BAND repeatedly to choose FM, MW, or LW. 2 Press TUNE MODE so that only “TUNING” appears in the display. “AUTO” should not appear in

47、 the display. 3 Turn TUNING/SELECT until you tune in the desired station. Turn the knob to the right for a higher frequency; turn it to the left for a lower frequency. The signal meter indicates the strength of the broadcast signal. Note When you reach the highest or lowest frequency of any band, tu

48、ning stops. Advanced Tuner Operations Numeric buttons BANDDIRECT 102501350 RadioFans.CN 10GB Advanced Tuner Operations Presetting Radio Stations This section shows you how to store up to 30 of your favorite FM or AM (MW and LW) stations manually onto preset codes made up of characters (A, B, or C) a

49、nd numbers (1-0), such as A7. You can store up to 10 stations on each of the 3 different letters. You can use these letters to classify stations according to music category or station band. 1Tune in the FM, MW, or LW station you wish to store. 2Press MEMORY. “MEMORY” appears along with the lowest vacant code to indicate that the tuner is ready to store the station. 3Press SHIFT to chose either A, B, or C. The letter you choose appears in the display. 4Press a numeric button (1-0). The tuner stores the station at the preset code you specified. 5Repeat