IC-R1500_user.pdf

《IC-R1500_user.pdf》由会员分享，可在线阅读，更多相关《IC-R1500_user.pdf（56页珍藏版）》请在收音机爱好者资料库上搜索。

1、INSTRUCTION MANUAL iR1500 COMMUNICATIONS RECEIVER i FOREWORD Thank you for purchasing this Icom receiver. The IC-R1500 COMMUNICATIONS RECEIVERis designed and built with Icoms state of the art technology and craftsmanship. With proper care, this receiver should provide you with years of trouble- free

2、 operation. We want to take a couple of moments of your time to thank you for making the IC-R1500 your radio of choice, and hope you agree with Icoms philosophy of “technology fi rst.” Many hours of research and development went into the design of your IC-R1500. DDFEATURES Wide frequency coverage wi

3、th all-mode re- ceive Both Remote controller operation and PC control application are available ANF and NR functions are available(Only when the optional DSP unit is installed.) IF shift function IMPORTANT READ ALL INSTRUCTIONScarefully and completely before using the receiver. SAVE THIS INSTRUCTION

4、 MANUALThis in- struction manual contains important operating instructions for the IC-R1500. EXPLICIT DEFINITIONS WORDDEFINITION R WARNING! CAUTION NOTE Personal injury, fi re hazard or electric shock may occur. Equipment damage may occur. Recommended for optimum use. No risk of personal injury, fi

5、re or electric shock. Icom, Icom Inc. and the logo are registered trademarks of Icom Incor- porated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. ii RWARNING! NEVERconnect the receiver via the OPC-254L to an AC outlet. This may pose a fi re

6、hazard or re- sult in an electric shock. RWARNING! NEVERoperate the receiver while dri- ving a vehicle. Safe driving requires your full attention any- thing less may result in an accident. NEVERconnect the receiver to a power source of more than 14 V DC. This will damage the receiver. NEVERconnect t

7、he receiver to a power source using re- verse polarity. This will damage the receiver. NEVERcut the DC power cable between the DC plug and fuse holder. If an incorrect connection is made after cutting, the receiver may be damaged. DO NOTleave the main unit powered ON and connected to a vehicles elec

8、trical system. The main unit draws approx. 550 mA. This will eventually drain the vehicles battery. NEVERexpose the receiver to rain, snow or any liquids. The receiver may be damaged. NEVERoperate or touch the receiver with wet hands. This may result in an electric shock or damage the receiver. NEVE

9、Rplace the receiver where normal operation of the vehicle may be hindered or where it could cause bodily injury. NEVERlet objects impede the operation of the cooling fan on the rear panel. AVOIDusing or placing the receiver in direct sunlight or in areas with temperatures below 10C (+14F) or above +

10、60C (+140F). BE CAREFUL!The receiver will become hot when op- erating it continuously for long periods. AVOIDsetting the receiver in a place without adequate ventilation. Heat dissipation may be affected, and the receiver may be damaged. AVOIDthe use of chemical agents such as benzine or al- cohol w

11、hen cleaning, as they can damage the receivers sur- faces. For U.S.A. only CAUTION: Changes or modifi cations to this device, not ex- pressly approved by Icom Inc., could void your authority to operate this device under FCC regulations. PRECAUTIONS iii TABLE OF CONTENTS FOREWORD . i IMPORTANT . i EX

12、PLICIT DEFINITIONS . i PRECAUTIONS . ii SUPPLIED ACCESSORIES . iii SPECIFICATIONS . iii TABLE OF CONTENTS . iii OPTIONS . iv 1 CONNECTION . 12 Rear panel connection. 1 Antenna installation . 2 2 PANEL DESCRIPTION . 37 Front panelcontroller . 3 Function displaycontroller . 5 Rear panelmain unit . 7 3

13、 SETTING A FREQUENCY . 810 Turning power ON/OFF . 8 Mode selection . 8 Tuning step selection . 9 Setting a frequency . 9 Receive mode selection . 10 4 BASIC OPERATION . 1115 Receiving . 11 Monitor function . 11 Lock function . 11 Attenuator function. 12 NB function . 12 AGC function . 12 SPECIFICATI

14、ONS Specifi cations are provided in the IC-PCR1500/IC-PCR2500s Instruction manual. SUPPLIED ACCESSORIES q Antenna 1 w AC adapter* 1 e USB cable 1 r CD 1 t Foot pad sheet 1 y Cable hanger 1 *Not supplied with some versions. y t re qw iv 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 AFC function . 13 VSC fun

15、ction . 13 IF fi lter selection . 14 IF shift function . 14 Duplex operation . 15 5 MEMORY OPERATION . 1624 General description . 16 Memory channel selection . 16 Programming a memory channel . 17 Programming channel names . 18 Copying memory contents . 19 Memory clearing . 21 Memory bank setting .

16、22 Memory bank selection . 23 Transferring bank contents . 23 6 SCAN OPERATION . 2529 Scan types . 25 Scan start/stop . 26 Scan edges programming . 27 Skip scan . 28 Scan resume condition . 29 7 PRIORITY WATCH . 30 Priority watch types . 30 Priority watch operation . 30 8 POCKET BEEP AND TONE SQUELC

17、H . 3134 Pocket beep operation . 31 Tone/DTCS squelch operation . 33 Tone scan . 34 9 SET MODE . 3543 General . 35 Set mode items . 35 10 OTHER FUNCTIONS . 4448 Weather channel operation . 44 DSP operation . 45 DATA cloning . 46 Partial reset. 47 All reset. 47 Internal audio switch. 48 11 TROUBLESHO

18、OTING . 49 12 DOC . 50 OPTIONS UT-106* DSP UNIT Provides AF DSP functions such as noise reduction and auto notch. CP-12LCIGARETTE LIGHTER CABLES For operation and charging via a 12 V cigarette lighter socket. OPC-254LDC POWER CABLES For operation and charging via an external power supply. SP-10 EXTE

19、RNAL SPEAKER For all-round mobile operation. Cable length: 1.5 m; 4.9 ft OPC-1156 SEPARATION CABLE For extended separate installation. 3.5 m; 11.5 ft *: UT-106 installation is described in the IC-PCR1500/IC-PCR2500s Instruction manual. 1 CONNECTION1 Rear panel connection D DC power supply connection

20、 Use a 12 V DC power supply with at least 4 A capacity. Make sure the ground terminal of the DC power supply is grounded. CONNECTING TO A DC POWER SUPPLY OPC-254L (optional) black white R CAUTION! NEVER remove the fuse- holders from the DC power cable. Connect to a 12 V DC battery. Pay attention to

21、polarities. NEVER connect to a 24 V bat- tery. This could dam- age the receiver. Solder Crimp NOTE: Use the terminals as shown below for the cable connections. D Fuse replacement Receiver Fuses (4 A) DC power supply 12 V to an AC outlet ? Ferrite core Controller CP-12L (optional) To a cigarette ligh

22、ter socket Fuse (4 A) Or Receiver To ground Supplied antenna The antenna holder is backed with double-sided tape. Remove the protective paper when the antenna is fixed to any place. To AC adapter 2 1CONNECTION 1 DD OPC-1156 connection q Connect the controller plug to the OPC-1156 jack. w Detach the

23、ferrite core from the controller cable, then at- tach it to the OPC-1156 as shown below. Make sure to wind the cable on the ferrite core. e Connect the OPC-1156 plug to the CONTROLLER con- nector of the receiver. Antenna installation D Antenna location To obtain maximum performance from the receiver

24、, select a high-quality antenna and mount it in a good location. It is not necessary to use radials on a magnetic mount (“mag mount”) antenna. Receiver OPC-1156 Controller Jack Ferrite core 3 PANEL DESCRIPTION2 q SETLOCK KEY SETLOCK Push to enter set mode. (p. 35) Push and hold for 1 sec. to turn th

25、e lock function ON and OFF. (p. 11) w TUNING STEP/MODE KEY TSMODE Push to enter tuning step selection mode. (p. 9) Rotate DIAL to select the desired tuning step. Push and hold for 1 sec. to enter receive mode selec- tion mode. (p. 10) Rotate DIAL to select the desired operating mode. e VOLUME CONTRO

26、L VOL (p. 11) Adjusts the audio level. r POWER KEY FOR CONTROLLER PWR Push to turn the controller power ON when its OFF. Push and hold for 1 sec. to turn the controller power OFF when its ON. t SQUELCH CONTROL SQL Varies the squelch level. (p. 11) S E T L O C K S . M W M W rewq !2!1!0oiuyt Function

27、display (p. 5) Front panelcontroller 4 2PANEL DESCRIPTION 2 y MONITORTONETONE SCAN KEY MONIT/T-SCAN Push to turn the monitor function ON and OFF. (p. 11) Push and hold for 1 sec. to enter tone squelch selection mode. (pgs. 31, 33) Tone squelch, pocket beep (CTCSS), tone squelch reverse action, DTCS

28、squelch, pocket beep (DTCS), DTCS squelch reverse action or tone function OFF can be selected. Push and hold for 1 sec. during tone squelch selection mode to start the tone scan. (p. 34) u NOISE BLANKER/AUTOMATIC GAIN CONTROL KEY NBAGC Push to turn the NB (Noise Blanker) function ON and OFF. (p. 12)

29、 The noise blanker function cannot be used in FM/WFM modes. Push and hold for 1 sec. to select the AGC (Automatic Gain Control) function Slow and Fast. (p. 12) While in FM or WFM mode, the AGC function is fi xed as Fast and AGC Slow cannot be selected. i ATTENUATOR/PRIORITY KEY ATTPRIO Push to turn

30、the ATT (Attenuator) function ON and OFF. (p. 12) Starts priority watch when pushed and held for 1 sec. (p. 30) o MEMORY/SKIP KEY MRSKIP Push to select the memory channel, memory bank or weather channel* modes. (pgs. 16, 23, 44) *Weather channels are available for USA/CANADA versions only. Push and

31、hold for 1 sec. to turn the channel skip setting ON and OFF for memory/frequency skip scan operation. (p. 28) !0 VFO/MHz TUNINGSCAN KEY V/MHzSCAN Selects and toggles VFO mode and band selection, 1 MHz or 10 MHz tuning when pushed. (p. 9) Starts scan when pushed and held for 1 sec. (p. 26) Cancels a

32、scan when pushed during scan. !1 TUNING DIAL DIAL Selects the operating frequency (p. 9), memory channel (p. 16), the setting of the set mode item (p. 35) and the scanning direction (p. 26). !2 MEMORY WRITE KEY S.MWMW (pgs. 17, 18, 21) Selects a memory channel for programming when pushed. Programs t

33、he selected memory channel when pushed and held for 1 sec. !3 POWER SWITCH FOR RECEIVER POWER Turns the receiver power ON and OFF. !3 5 2PANEL DESCRIPTION qAFC INDICATOR Appears when the AFC function is in use. (p. 13) wFM CENTER INDICATORS “” or “” appears when the received signal is not tuned to its center frequency; or the squelch is closed. “” appears when the received signal is tuned to its center frequency. eRECEIVE MODE INDICATORS Shows the selected receive mode. SSB (LSB/USB