Inspire_VLF-3_user_2011.pdf

《Inspire_VLF-3_user_2011.pdf》由会员分享，可在线阅读，更多相关《Inspire_VLF-3_user_2011.pdf（18页珍藏版）》请在收音机爱好者资料库上搜索。

1、VLF-3 Assembly Instructions 1 INSPIRE VLF-3 Receiver Kit Assembly Instructions The following assembly instructions should be followed carefully. The INSPIRE VLF-3 receiver kit is NOT a simple electronic assembly. If you follow the instructions carefully you should be successful in building a receive

2、r that works. If you are not careful, you run the risk of having a problem that is very difficult to locate and fix. Be careful, take your time, and GOOD LUCK! TOOLS NEEDED: Philips head screwdriver Small standard screwdriver Wire cutters Wire stripper Soldering iron (15-25 watt, small tip) Light du

3、ty resin core solder (60/40) Sponge Magnifying glass Solder sucker or solder wick KIT CONTENTS: 1. Black plastic enclosure 2. Face Plate 3. Printed Circuit Board (PCB) 4. Four bags of components: Bag 1 resistors, inductors Bag 2 capacitors Bag 3 ICs, diodes, sockets Bag 4 switches, jacks, knobs, ant

4、enna terminal, wires, misc. hardware VLF-3 Assembly Instructions 2 Printed Circuit Board (PCB): Faceplate Front Control Panel Component Side / Battery Side All electronic components are inserted from this side and soldered on the other side. The battery holder is inserted from this side also. Switch

5、 Side The four DPDT slide switches, the two 10k pots and the two LEDs are inserted from this side and soldered on the other side. VLF-3 Assembly Instructions 3 R5 + VLF-3 Assembly Instructions 4 ASSEMBLY SEQUENCE 1. Solder components to PCB. 2. Assemble jacks subassembly, connect wires to antenna te

6、rminal. 3. Connect wires to PCB. 4. Final assembly of receiver. 5. Test receiver. (Check off boxes as each step is completed.) 1. Solder components to PCB. (NOTE: The transistor (Q1) and the field effect transistor (J-FET with ferrite bead) have been preinstalled.) 1a. Sort and install resistors. Re

7、move the resistors from Bag 1. Leave the inductors for later installation. The colored bands on the resistors indicate the resistance using a color code. This table indicates how to convert each color to its numerical equivalent. 0 black 1 brown 2 red 3 orange 4 yellow 5 green 6 blue 7 violet 8 gray

8、 9 white gold: 5% tolerance. To read a resistor code, first locate the gold band and read the colors in order from the other end. (All resistors in this kit have a gold band indicating 5% tolerance.) The first two bands indicate digits in the resistance, the third band (called the multiplier) indica

9、tes the number of zeroes to be added to the digits to obtain the resistance. (NOTE: 1000 = kilo = k ; 1,000,000 = mega = Meg) Bag 1 Contents Resistors: R1 560 k R2 10 R3 2.2 Meg R4 22 Meg R5 680 R6, R12 220 (R7, R26 10k pots in Bag #4) R8 43 k R9, R17 10 k R10, R13 2.2 k R11 470 R14 100 k R15, R16,

10、R20 20 k R18 15 k R19, R25, R27 100 R21, R22, R23, R24 1 k R28 270 k Inductors L1 3.9 mH L2 150 mH Band 2 Band 3 Band 4 (gold) Band 1 VLF-3 Assembly Instructions 5 What is the resistance for each of the following? Example 1 Example 2 Example 3 Example 4 Band 1 Band 2 Band 3 brown black brown yellow

11、violet orange red black green orange orange orange Band 1 Band 2 Band 3 1 0 1 4 7 3 2 0 5 3 3 3 Resistance 100 100 47000 47 k 2000000 2 Meg 33000 33 k Use the resistor code to identify and sort all of the resistors. One good way to keep them sorted is to tape one end to a piece of paper and write th

12、e resistance and component number (R1, R2, etc.). Once you have identified and sorted all of the resistors, you are ready to solder them to the PCB. To prepare a resistor for insertion into the board, bend the two leads so that they form a right angle to the resistor body. Resistor locations on the

13、component side of the PCB are indicated with the “R” number from the parts list between the two holes for insertion of the leads. Part of the PCB showing location of R1, R3, R4 and R6. To install, place the leads of the resistor through the appropriate holes and press the resistor down against the c

14、omponent side of the PCB. (There is no required orientation for resistors. Either lead may be inserted in either hole.) Turn the board over while holding the resistor in position and bend the leads slightly outward to hold the resistor in place and solder the leads to the circuit side. (NOTE: There

15、will be an empty resistor symbol on the PCB between R15 and R20. No part will be installed in this location.) VLF-3 Assembly Instructions 6 STEPS FOR SOLDERING RESISTORS, CAPACITORS AND WIRES: IMPORTANT: DO NOT leave a soldering iron plugged in for a long time without using it. NEVER leave a hot sol

16、dering iron unattended. . PCB TRIM PCB Finished solder joint Soldering iron PCB Touch solder to the side of the lead away from the soldering iron. PCB lead contact PCB Press soldering iron firmly down against the contact and to the side against the lead. 1. Clean the tip of the iron by wiping it on

17、the wet sponge. 2. Place a small amount of solder on the tip. 3. Press the tip down against the circuit contact and against the resistor lead and hold for 5 seconds. 4. After the lead and the contact have heated for 5 seconds, apply the solder to the lead and contact (NOT directly to the iron) until

18、 the solder melts and flows around the lead and into the contact. 5. Apply enough solder to allow it to run down along the lead. Do not apply so much solder that it runs across the PCB surface. 6. After enough solder has been applied (1- 2 seconds), remove the solder wire but hold the iron in place

19、for another 2-3 seconds. 7. Remove the iron, allow the joint to cool and inspect the joint. 8. Trim the excess lead wire just above the solder joint. Repeat this process for the remaining resistors. Leave soldering iron in place for 1-2 more seconds. VLF-3 Assembly Instructions 7 IMPORTANT Note for

20、New Soldering Irons: A new soldering iron must be “tinned” in order to work well. Follow these steps: 1. Plug in the iron. 2. When it first heats up, apply solder liberally to the tip. 3. Wipe off the excess solder and you are ready to go! 1b. Install the IC sockets. Remove the IC sockets and IC1 (L

21、M386) and IC2 (LM358) from Bag #3. When installing IC sockets and ICs, alignment is very important. One end of the IC symbol on the PCB has a half-hole at one end of the symbol. One end of the socket has a half-hole. The IC itself has a circular dot near one end. Install the sockets so that the half

22、-hole end coincides with the half-hole on the PCB. Press the sockets firmly against the component side of the PCB. Solder the 8 pins on the other side of the PCB taking care not to create any solder “bridges” between the pins. Install the IC so that the end with the dot is at the end of the socket w

23、ith the half-hole. Carefully fit the 8 pins in the socket holes and press the IC firmly into the socket. IC PCB HALF HOLE DOT Socket PCB VLF-3 Assembly Instructions 8 1c. Solder capacitors to the PCB. Capacitor Identification Guide The small-value ceramic capacitors may be installed in either orient

24、ation, but the larger-value cylindrical capacitors (C4, C8, C10, C14, C16, C18, C19) must be installed with the proper polarity. The polarity is indicated on the PCB by a “+” sign near one end of the capacitor location. The polarity is indicated on the body of the capacitor with a stripe with a minu

25、s (-) sign located on the negative side of the capacitor. Also, the shorter lead is the negative lead. To install a capacitor, insert the leads in the appropriate holes and press the capacitor down near the PCB. Solder using the same technique as used for resistors. The polarity is not marked on cap

26、acitor C 10. The proper polarity is indicated here: NOTE: There may be some variation in capacitor markings due to using different suppliers. Bag #2 Contents Capacitors: C1, C3 24 pF C2, C6, C7 .01 F C4, C10, C18 10 F C5, C9, C13, C15, C17, C21, C22 C8 1 F C11, C12 .001 F C14, C16 330 F C19 100 F C2

27、0 .15 F .1 F C11, C12 .001 F “102” C1, C3 24 pF “240J0” C2, C6, C7 .01 F “103” C4, C10, C18 10 F C8 1 F C5 C9 C13 C15 C17 C21 C22 .1 F “104” C14, C16 330 F C19 100 F C20 .15 F “154” C 10 + VLF-3 Assembly Instructions 9 !1d. Install the inductors (L1 and L2) The inductors are the two remaining parts

28、in Bag #1. Inductor L1 is marked “LH 239”. Inductor L2 is marked “LJ 415”. From the component side, press the inductor firmly down against the PCB and solder the other side. There is no required polarity for the inductors. !1e. Install the diodes from Bag #3. Polarity is very important in the instal

29、lation of diodes. D1 and D2 are black cylinders with a silver stripe near one end. On the PCB, the D1 and D2 locations are shown as a rectangle with a stripe near one end. Align the striped end of the diode with the striped end of the PCB symbol. Press the diode firmly against the component side of

30、the PCB and solder the other side. Z1 and Z2 are small components with a black stripe near one end. The symbol on the PCB is the same as for D1 and D2. As with D1 and D2, align the black stripe end with the striped end on the PCB. Press the diodes firmly against the PCB and solder the other side. Re

31、turn the LEDs to Bag #3. They will be installed later. D1 1N 4004 Remaining Bag #3 Contents D1, D2Z1, Z2 LED1, LED2 VLF-3 Assembly Instructions 10 1f. Install the battery holder. From Bag #4, take the following parts: 1. Battery holder 2 PCB standoff post 2 4-40 3/8 “ screw 4 4-40 1/4” screw 2 4-40

32、nuts 2 nylon washers 2 #4 washers The following diagram shows the assembly of the battery holder to the PCB: . 1. Place the battery holder leads through the PCB from the component side and press the holder firmly against the PCB. 2. Insert 1/4” screws through the holes nearest the leads, through the

33、 PCB and tighten the nuts on the switch side. 3. Insert 3/8” screws through the other two holes, through the PCB, through the nylon washers and tighten the standoffs on the switch side. 4. Solder the battery leads on either (or both) side of the PCB. 5. Temporarily insert 1/4” screws through the #4

34、washers in the other ends of the standoffs. These will be used later to attach to the face plate. VLF-3 Assembly Instructions 11 1f. Install the potentiometer and switches. From Bag #4, remove the two 10k pots (R7 and R26) and the four DPDT slide switches. Slide the three contacts for the pots throu

35、gh the holes provided from the switch side of the PCB. Push the switch firmly against the PCB and solder either (or both) sides. Insert the six contacts for each DPDT slide switch into position and press the switch firmly against the switch side of the PCB. Solder each contact on the component side.

36、 1g. Install the LEDs. R7, R26 DPDT Switches DPDT Switches Align the LED leads as shown with the shorter lead closest to the line in the PCB symbol. Carefully work the LED down as far as it will go toward the PCB. When in the proper position, the top of the LED will be even with the tab on the adjac

37、ent power switch. Solder the LED leads to either side of the PCB. Carefully trim the excess leads. THIS COMPLETES THE INSTALLATION OF ALL PARTS ON THE PCB! VLF-3 Assembly Instructions 12 2. Attach wires to the PCB. Bag #4 contains the following wires: 3” red 4” orange 4” yellow 3” blue 3” black 5” w

38、hite Make the following cuts on the wires: 1 red: 1”, 2” 1 orange: 2”, 2” 1 yellow: 2”, 2” 1 blue: 3” 1 black: 1”, 2” 1 white: 2”, 1.5”, 1.5” To prepare a wire for soldering, strip about 1/8” of insulation from each end. To solder a wire to the PCB: 1. insert the wire into the component side, 2. pre

39、ss the soldering iron to the wire and to the metal pad on the PCB for about 5 seconds to heat both the wire and the pad, 3. apply solder to the side away from the soldering iron making sure that the wire and pad melt the solder, not the soldering iron. Solder the 1” red wire to the ANT connection on

40、 the PCB. Solder the 1” black wire to the RTN connection on the PCB The wire connections to the PCB are numbered 1-7. Connect the following wires to the appropriate locations: Connection 1: 2” red wire Connection 2: 2” black wire and 2” white wire twisted together Connection 3: 2” orange wire Connec

41、tion 4: 2” orange wire Connection 5: 2” yellow wire Connection 6: 2” yellow wire Connection 7: 3” blue wire See also the photos on the following page. ANT RTN VLF-3 Assembly Instructions 13 Wires installed (component-side view) Wires installed (switch-side view) Close up of white and black wire twis

42、ted together prior to being soldered to location #2 on the PCB. VLF-3 Assembly Instructions 14 3. Install the jacks and connectors to the faceplate. Install the jacks and the external power connector to the faceplate by inserting them from the back side and tightening the knurled nut on the front si

43、de. Mount the 2-screw antenna terminal to the faceplate by placing the terminal in front of the faceplate and using the two remaining 4-40 1/4” screws and nuts. Mount the BNC connector by removing the nut and washer, inserting the connector from the front of the panel and tightening the nut over the

44、 washer. 4. Attach the PCB to the faceplate. Remove the nuts and washers from the standoffs and the nuts from the shafts of the 10k pots. Attach the faceplate to the PCB by fitting the faceplate over the switches and LEDs. Tighten the screws and washers to the standoffs. Tighten the nuts on the 10k

45、pot shafts. 5. Solder wires to jacks and connectors. To solder the wire to a jack contact: 1. insert the wire through the hole in the tab, 2. press the soldering iron to both the wire and the tab and heat for 5 seconds, 3. apply the solder to the side away from the soldering iron, making sure that t

46、he wire and tab melt the solder, not the iron. Use the following figure as a guide for wiring connections to the jacks and the external power connector. See also the photo on the next page. The monaural jack (white body) is the MIC jack. The blue wire connects to this jack. The center two are the Au

47、dio and Data jacks and are the black body stereo type. The round one is the external power connector. 2 White White White MIC AUDIO DATA POWER Yellow Blue Orange Orange Black Red Yellow NOTES: 1. The yellow and orange wires must cross to reach the correct jacks. 2. The white ground wire and the black wire both connect to Location 2. VLF-3 Assembly Instructions 15 Close-up showing wires soldered to the jack tabs. NOTE: The orange and yellow wires must cross to connect to the appropriate jacks. The microphone connector may be either white (as pictured) or black