Philips-DVDR-5350-H-Service-Manual(1) 电路图 维修手册.pdf

《Philips-DVDR-5350-H-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Philips-DVDR-5350-H-Service-Manual(1) 电路图 维修手册.pdf（14页珍藏版）》请在收音机爱好者资料库上搜索。

1、Published by KC-TE 0541 AV Systems Printed in the Netherlands Subject to modifi cation EN 3139 785 31540 DVDR5350H & DVDR7300HHDD & DVD Recorder Service Instruction CLASS 1 LASER PRODUCT Contents Page 1 Technical Specifi cations and Connection Facilities 2 2 Test Disc & Repair Hints 5 3 Firmware Upg

2、rading 6 4 Service Flow chart 7 5 Directions For Use 12 Copyright 2005 Philips Consumer Electronics B.V. Eindhoven, The Netherlands. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, p

3、hotocopying, or otherwise without the prior permission of Philips. Version 1.0 DVDR5350H/02/19 & DVDR7300H/02/05/19 The 2005 range DVD Recorder products are repaired centrally. Defective sets must be identifi ed, labelled and stored for pick-up. This document gives full instructions for a functional

4、 check. Technical information to repair faulty sets is therefore not provided in this document. To test in-coming sets the following must be performed: 1. Verify / Reproduce the customers problem 2. Verify that set has latest Firmware (see chapter 3) and upgrade if it is not the latest version. 3. F

5、ull functional check RadioFans.CN 收音机爱 好者资料库 EN 23139 785 315401. Technical Specifi cations and Connection Facilities 1. Technical Specifi cations and Connection Facilities 1.1 General: Mains voltage : 220V 240V Mains frequency : 50 Hz Power consumption (record) : 40 W Standby Power Consumption : 4

6、W Eco standby : 3 W 1.2 RF Tuner Test equipment: Fluke 54200 TV Signal generator Test streams: PAL BG Philips Standard test pattern 1.2.1 System PAL B/G, PAL D/K, SECAM L/L, PAL I 1.2.2 RF - Loop Through: Frequency range : 45 MHz 860 MHz Gain: (ANT IN - ANT OUT) : -6dB to 0dB 1.2.3 Receiver: PLL tun

7、ing with AFC for optimum reception Frequency range : 45.25 MHz 857 MHz Sensitivity at 40dB S/N (video unweighted) : 60dBV at 75 1.2.4 Video Performance: Channel 25 / 503,25 MHz, Test pattern: PAL BG PHILIPS standard test pattern, RF Level 74dBV, Measured on SCART 1 Frequency response : 0.1 MHz 4 MHz

8、 3dB Group delay (0.1 MHz - 4.4 MHz) : 0 nsec 150 nsec 1.2.5 Audio Performance: Audio Performance Analogue - HiFi: Frequency response at SCART 1 (L+R) output : 100 Hz 12 kHz / 0 3dB S/N Ratio (20Hz 20kHz) unweighted : 50dB Harmonic distortion (1 kHz, 25 kHz deviation) : 1.5% Audio Performance NICAM:

9、 Frequency response at SCART 1 (L+R) output : 40 Hz 15 kHz / 0 3dB S/N Ratio (20Hz 20kHz) unweighted : 60dB Harmonic distortion (1kHz, 25 kHz deviation) : 0.5% 1.2.6 Tuning Automatic Search Tuning Scanning time without RF signal : 3min. typical Stop level (vision carrier) : 37dB/V Maximum tuning err

10、or of a recalled program : 100 kHz Maximum tuning error (drift) during operation : 100 kHz Tuning Principle: Automatic B, G, I, DK and L/L detection Manual selection in “STORE” mode 1.3 Analog Inputs / Outputs 1.3.1 SCART 1 (Connected to TV) Pin Signals: 1 Audio-out R 1.8V RMS 2 Audio-in R 3 Audio-o

11、ut L 1.8V RMS 4 Audio GND 5 Blue / Chroma GND 6 Audio-in L 7 Blue-out 0.7Vpp 0.1V into 75 8 Function switch 4.5V / 9.5V / 12V = asp. Ratio 4:3 DVD 9 Green GND 10 P50 control not use 11 Green out 0.7Vpp 0.1V into 75 12 NC 13 Red / Chroma GND 14 Fast switch GND 15 Red-out / 0.7Vpp 0.1V into 75 Chroma-

12、out 300mVpp 3dB 16 Fast switch RGB / CVBS or Y out 1V / 10k Video - Cinch Input voltage : 1Vpp 3dB Input impedance : 75 Video - YC (Hosiden) According to IEC 933-5 Superimposed DC-level on pin 4 (load 100k) 3.5V is detected as 16:9 aspect ratio Input voltage Y : 1Vpp 3dB Input impedance Y : 75 Input

13、 voltage C : 300mVpp 3dB Input impedance C : 75 1.3.4 Out 1 Component Video Cinch Y/Pb/Pr according EIO-770-I-A, EIA-770-2 Audio - Cinch Output voltage : 2Vrms max. Output impedance : 10k 1.3.5 Out 2 Audio - Cinch Output voltage : 2Vrms max. Output impedance : 10k Video - Cinch Output voltage : 1Vpp

14、 3dB Output impedance : 75 Video - YC (Hosiden) According to IEC 933-5 Superimposed DC-level on pin 4 (load 100k) 3.5V is detected as 16:9 aspect ratio Output voltage Y : 1Vpp 3dB Input impedance : 75 Output voltage C : 300mVpp 3dB Input impedance : 75 1.4 Digital Inputs / Outputs 1.4.1 Digital Outp

15、ut Digital Audio Coaxial / Optical LCM : according IEC 60958 MPEG 1, MPEG 2, AC3 : according IEC 61937 DTS : according IEC 61937 + addendum 1.4.2 HDMI Output Type A connector (19 pins) 1.4.3 Digital Video Input (IEEE 1394) Implementation Standard according: IEEE Std 1394-1995 IEC61883 - Part1 IEC618

16、83 - Part 2 SD-DVCR (02-01-1997) Specifi cation of consumer use digital VCRs using 6.3mm magnetic tape dec.1994 Mechanical connection according to Annex of IEC 61883-1 1.4.4 G-Link (for IR-remote transmitting device) Output voltage : 5 0.5V (high level) 0.4 0.3V (low level) Output impedance : 150 1.

17、5 Video Performance All outputs loaded with 75 SNR measurements over full bandwidth without weighting. 1.5.1 SCART (RGB) SNR : 55dB on all output Bandwidth : 4.8MHz -3dB 1.6 Audio Performance 1.6.1 Cinch Output Rear Output voltage 2 channel mode : 2Vrms 2dB Channel unbalance (1kHz) : 100dB Crosstalk

18、 16Hz-20kHz : 87dB Frequency response 20Hz-20kHz : 0.5dB Signal to noise ratio (unweighted) : 85dB Dynamic range 1kHz : 83dB Distortion and noise 1kHz : 83dB Distortion and noise 16Hz-20kHz : 75dB Intermodulation distortion : 70dB Mute : 95dB 1.6.2 Scart Audio Output voltage 2 channel mode : 1.6Vrms

19、 2dB Channel unbalance (1kHz) : 85dB Crosstalk 16Hz-20kHz : 70dB Frequency response 20Hz-20kHz : 0.5dB Signal to noise ratio (unweighted) : 80dB Dynamic range 1kHz : 75dB Distortion and noise 1kHz : 75dB Distortion and noise 16Hz-20kHz : 50dB Intermodulation distortion : 70dB Mute : 80dB 1.7 Dimensi

20、ons and Weight Height of feet : 5.5mm Apparatus tray closed : WxDxH:435x335x76mm Apparatus tray open : WxDxH:435x472x76mm Weight without packaging : 5kg Weight with packaging : 8kg 1.8 Laser Output Power & Wavelength 1.8.1 DVD Output power during reading : 0.8mW Output power during writing : 20mW Wa

21、velength : 650nm 1.8.2 CD Output power : 0.3mW Wavelength : 780nm RadioFans.CN 收音机爱 好者资料库 EN 43139 785 315401. Technical Specifi cations and Connection Facilities 1.9 Read / Write Speed Type of Disc (Function)Disc Rotation Speed Read Speed CD7X CAV Read Speed DVD4X CAV Write Speed DVD+R/+RW2.4X ZCAV

22、 Write Speed DVD-R/-RW2X 1.10 Commercial Difference DVDR5350HDVDR7300H HDD capacity160GB250GB HDMIx 1.11 Playability DVDR5350HDVDR7300H Video Playback 1.Disc Media: CD-R/-RW, MP3- CD, VCD/SVCD, DVD-Video, DVD+R/+RW, DVD-R/-RW xx 2.Compression Format: MPEG1, MPEG2 xx Audio Playback 1.Disc Media: CD,

23、CD-R/-RW, MP3-CD xx 2.Compression Format: Dolby Digital, MP3, MPEG2 Multi- channel, PCM xx 3.MP3 bit rates: 32- 256 kbps and VBR xx Still Picture Playback 1.Disc Media: Picture CD xx 2.Picture Compression Format: JPEG xx EN 53139 785 315402.Test Disc & Repair Hints 2. Test Disc & Repair Hints 2.1 Te

24、st Disc 1) 7104 099 96611 CD-RW printed Audio Disc 2) 9965 000 25728 DVD Player Test Pack 3) - Blank DVD+RW 4) - Blank DVD-RW 2.2 Open the DVD Tray manually Note: This procedure needs to be performed on condition that: - a customers Disc is jammed in the DVD Tray - the DVD Tray cannot be open via th

25、e normal open/close button on the set. 1) Place the set on the table with the bottom faced upwards as shown below. 2) Insert a screw driver into the slot and open the DVD Tray by sliding the screw driver in the direction shown. Figure 2-1 1 2 EN 63139 785 315403.Firmware Upgrading 3. Firmware Upgrad

26、ing 3.1 Firmware Upgrading A. Preparation to upgrade fi rmware: 1. Unzip the zip-archive fi le 2. Start the CD Burning software and create a new CD project (data disc) with the following settings: File system : Joliet Format : MODE 2: CDROM XA Recording mode : SINGLE SESSION (TRACK-AT-ONCE), FINALIZ

27、ED CD Note: Long fi le name is necessary for the preparation of the upgrade disc 3. Place the content of the zip-archive into the root directory of the new CD project. 4. Burn the data onto a blank CDR or CD-RW B. Procedure to apply the fi rmware upgrade: 1. Hold the + buttons down and Power up the

28、set. 2. The tray opens and set will display: DOWNLOAD .INSERT DISC 3. Insert the prepared Upgrade CDROM and close the tray. 4. The set will display: INIT DISC DOWNLOAD . The whole process takes less than 10 minutes Note: Do not press any buttons or interrupt the mains supply during the upgrading pro

29、cess, otherwise the set may becomes defective. 5. When the upgrade is completed the tray will open automatically and the set will display: REMOVE DISC 6. Close the tray and the set will display: DONE 7. The set will go into Standby mode. C. How to read out the fi rmware version to confi rm set has b

30、een upgraded: 1. Power up the set. 2. Press button on the Remote control and select Setup option 3. Press button to select System 4. The set will prompt you about clearing the Time Shift Buffer 5. Select Yes and press button 6. Press button several times to select Version info 7. Press button 8. The

31、 TV connected to the set will display: DIF05_5/56299AN SV11201 BE 43.2.13 ASP1,18,1,10FP SIT5300-FNAC6-S3_299-F536_B1 20050909-1857 dev sxc EPG:DPMS:P_DPM 9. Press button to exit EN 73139 785 315404.Service Flow Chart 4. Service Flow Chart 4.1 Start Process Start A (Verification Test) Is it a Hardwa

32、re problem ? Upgrade to latest Firmware Is it a known complaint ? Is Firmware solution available ? Yes No Yes No Yes No Is the complaint solved ? Return set to Customer with Report on action done Yes No Is the complaint documented ? Yes No Service W/S to contact the Trade / Customer to work out an a

33、ction plan. Examples: - explain them that the Firmware solution is not ready - Upgrade disc will be send to them the moment a solution is ready - etc. Does the set pass the Dealer Test ? Pass Fail Perform built-in Dealer Test (Press & hold Play button on Front Panel down + Power-up the set) Send ref

34、urbished set from pool stock to Trade / customer - Attached Defect Description Report and Proof of Purchase. - Pack defective set - Store defective set for pick-up EN 83139 785 315404.Service Flow Chart 4.2 Verifi cation Process * If complaint is related to System Menu setting Connect up the Recorde

35、r to TV antenna, TV set and an External source Check the Firmware version on the set Can the set Start-up ? Yes No A (Verification Test) B Recording Check C Playback Check D * System Menu Send refurbished set from pool stock to Trade / customer Return set to Customer with Report on action done - Att

36、ached Defect Description Report and Proof of Purchase. - Pack defective set - Store defective set for pick-up No Yes Is Firmware the last released version ? Upgrade to latest Firmware Are the checks result ok ? Yes No EN 93139 785 315404.Service Flow Chart 4.3 Recording Process Manual Recording with

37、 TSBHDD: Manual Recording Copy to DVD Recordable discTimer Recording Does Timer recording functions ? Yes No Does manual recording functions ? Yes No B Recording Check Make a Timer recording with: - VPS/PDC on and off - Guide Plus+ System - Show View System - manual recording Playback the recorded t

38、itle from HDD browser Are Timer edit & delete feature working ? Yes No Make a manual recording to the HDD using different recording source: - Cam 1 (Front CVBS/S-Video) - Cam 2 (DV-in) - Tuner - Rear Ext 1/2 (external Cable Box/Satellite Receiver/VCR/DVD) From the HDD browser select the recorded tit

39、le and check the following: - edit title feature - play the title Does the TSB feature works ? 1) Switch the Recorder to Tuner source - The active Tuner channel will be recorded into the TSB (time shift buffer), a temporary HDD storage area. 2) By pressing the INFO button the Time shift bar appears

40、on the screen, check the following features: - search forward / backward - instant replay, pause, etc. on the live TV function 1) Make a short recording (1 minute) by selecting a portion in the TSB to be recorded. 2) Playback the recorded title from the HDD browser Does the recording functions ? Con

41、tinue Continue Yes No Yes No Send refurbished set from pool stock to Trade / customer - Attached Defect Description Report and Proof of Purchase. - Pack defective set - Store defective set for pick-up 1) Insert a DVD+RW disc 2) In the HDD browser select the recorded title for copy to recordable DVD

42、3) From the Disc Menu select the copied title and check the following: - edit (Disc/Title) feature - play the title 4) Repeat with DVD-RW Does copy function ? Yes No Is the Disc Library feature working ? Yes No EN 103139 785 315404.Service Flow Chart 4.4 Playback Process HDD playback CheckDisc playb

43、ack Check Yes No C Playback Check Playing other type of disc: 1) Use discs of DVD PLAYER TEST PACK for: - (Super) Video CD - MP3 disc - Picture disc (slide show) - special DVD playback check by layer change test using DVD disc of this package 2) For AUDIO CD use of CD-RW printed Audio Disc to check:

44、 - Track 3 finger print - Track 8: 600u black dot (max. after 1 min.) From the DVD Menu play a DVD video disc title and check the following: - Pause, Jump functions & Next / Previous chapter - Edit features (for DVD+RW) - T/C tools - Toolbar options Yes No Does the set work ? From the HDD browser ch

45、eck the following features: - Sorting - Delete, Copy,Child Lock & Protect - Edit features Does the set work ? ContinueContinue Yes No Send refurbished set from pool stock to Trade / customer - Attached Defect Description Report and Proof of Purchase. - Pack defective set - Store defective set for pi

46、ck-up Does the set work ? Play a title from the HDD browser and check the following features: - Pause, Jump functions & Next / Previous chapter - Editing features - Yes NoDoes the set work ? EN 113139 785 31540 4.5 System Menu Process 4.Service Flow Chart D System Menu Check Does the set work ? Cont

47、inue Yes No Toolbar - check the following features: - Option Setup - check the following features: - System - Time-date - Analogue Ch - Video output - Audio output - Audio input - Language Preference - check the following features: - Recording - DV Specials - Sound - Disc - Access - Features Send re

48、furbished set from pool stock to Trade / customer - Attached Defect Description Report and Proof of Purchase. - Pack defective set - Store defective set for pick-up EN 123139 785 31540 5. Directions For Use The following except of the Quick Use Guide serves as an introduction to the set. The Complete Direction for the Use can be downloaded in different languages from the internet site of Philips Customer care Center: 5.Directions For Use COPY PAUSE BROWSER BACK Record Mode HQ SP SPP LP EP SLP SEP Hours of recordings can be stored on the HDD or an empty DVD recordable disc. 1 2 2.5 3